Monitor Cap Kits
racergiant:
Started by Mark -
Zanen Monitor Repair Kits
Monitor Get Well Kits
Save time and money on monitor repairs
Monitor repair kits take care of picture warping, blacking out, smearing, low brightness and brightness problems, poor voltage regulation, jail bars, vertical shrinking, etc. Call for free technical help with your monitor problems. All kits come with complete instructions and are easy to install.
Zanen Electronics
5023 52nd Street
Lubbock, TX 7914
Phone: 806 793 6337
Fax: 806 793 9136
EDITED FOR NEW ADDRESS SEE REPLY #16 FOR CURRENT INFO. CAPTAINHAPPY 7-20-06
Visa and Mastercard accepted.
Discount! Buy any 10 kits and take $1.00 off each kit.
Free shipping for orders over $25.00
Monitor repair kits which are currently available:
101 For Electrohome G07-CBO 19" color monitor.
Includes 17 parts. $7.95 ea.
102 For Electrohome G07-FBO 13" color monitor.
Includes 16 parts. $7.95 ea.
103 For Electrohome G19-411 13" color monitor.
Includes 21 parts. $7.95 ea.
104 For Electrohome G802/805 19" B&W X-Y monitor.
Includes 9 parts. $4.95 ea.
105 For Electrohome G19-CC0 13" and 19" color monitor.
Includes 20 parts. $7.95 ea.
110 For Electrohome G08-003 19" X-Y color monitor.
Includes 4 deflection trans. 19 parts. $8.95 ea.
[NOTE: The kit contains 4 2N3716's. These are NOT the correct
deflection transistors for this monitor]
201A For Wells-Gardner K4600 series 19" color monitor.
Includes brightness control. 21 parts. $6.95 ea.
202 For Wells-Gardner K4900 series 19" color monitor.
Includes 16 parts. $7.95 ea.
203 For Wells-Gardner K4800 series 13" color monitor.
Includes 16 parts. $7.95 ea.
204 For Wells-Gardner K7000 series 13", 19", and 25" color monitors.
Includes 15 parts. $6.95 ea.
206 For Wells-Gardner 19K6100 X-Y 19" color monitor.
Includes 30 parts. Includes 6 deflection transistors. $14.95 ea.
207 For Wells-Gardner K4500 series color monitor.
Includes 18 parts. $6.95 ea.
208 For Wells-Garder 19V2000 19" B-W X-Y monitor.
Includes 11 parts. $4.95
301 For Nintendo Sanyo 20-ezv(r-b,v) 19" color monitor.
Includes 16 parts. $6.95 ea.
302 For Nintendo Sharp XM-1801N or XM-2001N 19" color monitor.
Includes 24 parts. $7.95 ea.
303 For Sanyo 14" color monitor.
Includes 14 parts. $6.95 ea.
401 For Atari Disco 2090DT-2B 19" color monitor.
Includes 14 parts. $6.95 ea.
402 For Atari Disco AGM20M 19" medium resolution color monitor.
Includes 21 parts. $7.95 ea.
501 For WICO Videomaster 10" and 19" color monitors.
Includes 22 parts. $7.95 ea.
510 For Imperial 13" #44-4013 and 19" #44-4019.
Includes 21 parts. $7.95 ea.
530 For Ceronix model 1492 19" color monitor.
Includes 16 parts. $6.95 ea.
601 For Korean Telcom AK901 9" and 13" color monitors.
Includes 24 parts. $9.95 ea.
602 For Sharp Image OC-1411 13" and 19" color monitors.
Includes 19 parts. $7.95 ea.
603 For Sega MC-2000 13" and 19" color monitors.
Includes 24 parts. $7.95 ea.
604 For Sampo model KGR-1901 19" monitor.
Includes 20 parts. $7.95 ea.
605 For QNIC model CGM-2500 25" color monitor.
Includes 21 parts. $7.95 ea.
606 For Sharp Image model 0C-2022 19" color monitor.
Includes 25 parts. $7.95 ea.
608 For Sharp Image model SI-327 27" color monitor.
Includes 25 parts. $8.95 ea.
609 For Sharp Image model SI-313 13" and SI-319 19" color monitors.
Includes 23 parts. $7.95 ea.
611 For Sharp Image model 0C-2021 19" color monitor.
Includes 22 parts. $7.95 ea.
616 For Tatung model VS-1443 19" color monitor.
Includes 26 parts. $8.95 ea.
620 For the Toei 19" color monitor.
Includes 28 parts. $8.95 ea.
701 For Matsushita TM202G 19" color monitor.
Includes 17 parts. $6.95 ea.
801 For Hantarex MTC-900 19" color monitor.
Includes 21 parts. $7.95 ea.
802 For Hantarex MTC-9000 19" color monitor.
Includes 18 parts. $7.95 ea.
910 Nintendo Sanyo video inversion kit.
Eliminates the need for a color inverion board.
Includes 15 parts. $4.95 ea.
[NOTE: this permanently changes your Sanyo monitor to
"normal" RGB...so you'll need to invert the output
from your Nintendo boards that put out inverse RGB.
Obviously this is to run non-Nin boards with the Sanyo.]
920 For Pac Man, Ms Pac Man logic boards. Eliminates hum bar
in picture. Includes 4 parts. $6.95 ea.
Misc Parts
15 Amp PS (1 year warranty) $27.95 ea.
Flyback transformers:
A29951-B for Electrohome G07-CB0 19" $28.95 ea.
Hantarex monitors, all model and sizes $38.95 ea.
Wells-Gardner K7000 series monitors $34.95 ea.
Width coil C30380-A for Electrohome monitors $8.25 ea.
2SC1106 Transistor $4.89 ea.
2SC3039 Transistor (Sanyo) $1.79 ea.
2SD870 Transistor $4.49 ea.
1.5 Amp GMA 20 x 5mm pigtail fuse $0.39 ea.
« Last Edit: July 20, 2006, 04:05:50 PM by captainhappy »
racergiant:
By Mark -
Kit # 101 Installation Instructions
This monitor repair kit is designed for the Electrohome G07-CBO 19
inch color monitor.
Be sure to check that all the parts are included in the kit:
1 1 uF @ 50V or 63V 1 2200 uF @ 25V
1 4.7 uF 0 50V 1 1 uF @ 250V
1 4.7 uF @63Vor 100V 1 3.3 uF @ 160V
1 10 uF @50V 2 10 uF 0 250V
1 33 uF @25V 1 47 uF @ 200V
3 100 uF @ 16V 1 100 uF @ 160V
2 220 uF @ 16V
Be sure to install all the parts on the monitor even though many of
the original
parts seem to be working fine. Age, humidity, and temperature will
cause the value of electrolytic capacitors to change. Installing all
of the parts will assure many more years of trouble free service. Each
capacitor is polarized and can only be inserted in one direction.
Watch the polarity markings on each capacitor. On the top side of the
monitoriaard where each capacitor is located is a circle with a black
dot on. one side. The black dot indicates where the negative (-) lead
is to be inserted.
Remove the shield over IC501 and install the following parts.
C302 220 uF @ 16V C511' 47 uF @ 200V
C403 100 uF @ 16V C517 100 uF @ 16V
C407 4.7 uF @ 63V or 100V C518 220 uF @ 16V
C408 4.7 uF @ 50V C521 2200 uF @ 25V
C411 100 uF @ 160V C523 1 uF 0 250V
C412 3.3 uF @ 160V C701 100 uF @ 16V
C504 1 uF @ 50V or 63V C905 10 uF @ 250V
C506 33 uF @ 25V C107 10 uF @ 250V - Neck Board
IMPORTANT! Be sure to install the negative lead of C302 into the hole
with the black dot shown on the top side of the chassis. The (+) sign
on the bottom side of C302 is marked incorrectly. The last step is to
install a sync modification which prevents a horizontal curl. This
step is optional. On the monitor board, replace C303 with the 10uF 0
50V capacitor with the positive lead connected to the collector of
X305. Then replace C501 with the capacitor taken from space C303.
racergiant:
By Mark -
Kit # 104 Installation Instructions
This monitor repair kit is designed for the Electrohome 605-802/805
monochrome monitor.
Be sure to check that all the parts are included in the kit:
4 2.2 uF 0 50V 1 4.7 uF 0 250V
1 47 uF @50V 1 47 uF @ 200V
2 1000 uF @ 50V
Be sure to install all the parts on the monitor even though many of
the original parts seem to be working fine. Age, humidity, and
temperature will cause the value of electrolytic capacitors to change.
Installing all of the parts will assure many more years of trouble
free service. Each capacitor is polarized and can only be inserted in
one direction. Watch the polarity markings on each capacitor. On the
top side of the monitor board where each capacitor is located is a
pius sign next to one of the two holes where the capacitor leads are
to be inserted. The plus sign indicates where the positive (+) lead on
the capacitor is to be inserted.
Make sure the game is unplugged and install the following parts.
C900 1000 uF @ 50V C500 2.2 uF @ 50V
C901 1000 uF @ 50V C501 2.2 uF @ 50V
C904 47 uF 0 50V C502 2.2 uF @ 50V
C908 4.7 uF @ 250V C503 2.2 uF @ 50V
C504 47 uF @ 200V
A source for many problems with this monitor is loose solder
connections. It is very common for loose connections to develop where
plugs are soldered to the main and high voltage circuit boards.
ZANEN ELECTRONICS
5023 52nd Street
Lubbock, Texas 79414
806-793-6337 Fax: 806-793-9136
racergiant:
By Mark -
Kit # 110 Installation Instructions
This monitor repair kit is designed for the Electrohome G08-003 19
inch X-Y color monitors. Be sure to check that all the parts are
included in the kit:
2 4.7 uF @ 50V 1 1000 uF @ 50V
6 10 uF @50V 1 22 uF @ 250V
2 22 uF @25V 1 47 uF @ 200V
2 47 uF @ 16V or 25V 4 2N3716 Transistor
1 100 uF @ 16V
Be sure to install all the parts on the monitor even though many of
the original parts seem to be working fine. Age, humidity, and
temperature will cause the value of electrolytic capacitors to change.
Installing all of the parts will assure many more years of trouble
free service.
Each capacitor is polarized and can only be inserted in one direction.
Be sure to watch the markings for polarity on each capacitor.
Make sure the game is unplugged and install the following parts.
C401 1000 uF @ 50V C900 4.7 uF @ 50V
C405 10 uF @ 50V C901 4.7 uF @ 50V
C406 10 uF @ 50V C904 22 uF @ 25V
C411 22 uF @250V C905 22 uF 0 25V
C601 47 uF @ 16V or 25V C911 100 uF @ 16V
C701 47 uF @ 16V or 25V C916 47 uF @ 200V
C800 10 uF @ 50V Q605 2N3716
C801 10 uF @ 50V Q606 2N3716
C802 10 uF @ 50V Q705 2N3716
CS03 10 uF @ 50V Q706 2N3716
racergiant:
By Mark -
Kit # 206 Installation Instructions
This monitor repair kit is designed for the Wells-Gardner 19K6100 X-Y
color monitor.
Be sure to check that all the parts are included in the kit:
1 22 uF @ 50V 1 25K Potentiometer
1 47 uF @ 50V 2 1N4148 Diode
2 100 uF @ 50V 2 1N4750 27V Diode
1 10 uF @ 350V 1 Z150B 150V Diode
1 33 uF @ 160V 3 MPSA06 Transistor
1 33 uF @ 250V 1 MPSA56 Transistor
2 2.2 ohm @ 2 Watt 1 2N3904 Transistor
2 15 ohm @1/2 Watt 3 2N3716 Transistor
2 330 ohm @ 1l4 Watt 3 2N3792 Transistor
Be sure to install all the parts on the monitor even though many of
the original parts seem to be working fine. Age, humidty, and
temperature will cause the value of electrolytic capacitors to change.
Each capacitor is polarized and can only be inserted in one direction.
Watch the polarity markings on each capacitor. On the top side of the
monitor board where each capacitor is located is a circle with a plus
sign next to one of the holes. The plus sign indicates where the
positive (+) lead of each capacitor is to be inserted. It is possible
for a failure on the game logic board to cause the monitor to fail.
There is a simple test to find out if the game board caused the
monitor to fail. To perform the test you will need a voltmeter. Set
the voltmeter on the DC voltage scale and measure the voltage on the
lead of R600 and R700 which is connected to the yellow and orange
respectively. The correct voltage should be around zero volts DC but
fluctuate because of the changing deflection signal. If the measured
voltage is between 5 and 15 volts positive or negative DC then check
the X and Y amplifiers on the game board. Also check for broken
potentiometers on the logic board.
It is very important to resolder all connectors soldered to the
circuit boards. Loose connections commonly develope because plugs are
removed and plugged back. The following parts are both on the
deflection and high voltage boards.
Unplug the game and replace the following parts.
C901 100 uF @ 50V ZD100 1N4750 27V Diode
C902 100 uF @ 50V ZD101 1N4750 27V Diode
C905 33 uF @ 160V ZD902 Z150B 150V Diode
C909 22 uF @ 50V Q100 MPSA06 Transistor
C910 10 uF @ 350V Q101 MPSA56 Transistor
C914 47 uF @ 50V Q102 2N3716 Transistor
R100 15 ohm @ 1/2 Watt Q103 2N3792 Transistor
R101 15 ohm @ 1/2 Watt Q605 2N3716 Transistor
R102 330 ohm @ 1/4 Watt Q606 2N3792 Transistor
R103 330 ohm @ 1/4 Watt Q705 2N3716 Transistor
R901 2.2 ohm @ 2 Watt Q706 2N3792 Transistor
R907 2.2 ohm @ 2 Watt Q901 MPSA06 Transistor
R918 25K Potentiometer. Q902 MPSAG6 Transistor
D104 1N4148 Diode Q903 2N3904 Transistor
D105 1N4148 Diode C503 33 uF @ 250V
Navigation
[0] Message Index
[#] Next page