Welcome, Guest. Please login or register.
June 01, 2024, 03:33:30 AM

Login with username, password and session length
* Home Help Arcade Login Register
.
+  Forum
|-+  **Reel Slots** Gaming Machines
| |-+  Bally Reel Games. (Moderator: a69mopar)
| | |-+  Bally S6000 20 Error		 0 Members and 1 Guest are viewing this topic. « previous next »
Pages: [1] Go Down Print
Author Topic: Bally S6000 20 Error  (Read 4087 times)
reho33
Contributing NLG Member
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 146
Offline Offline

Gender: Male
Posts: 1594


Slot Losers of America / Tokie Owens
« on: November 19, 2009, 03:01:23 AM »
I just got all the pieces to make this slot coin again. The hopper actually pays out and all is well. The comparitor is a CC-16D and lights up properly when installed. However a 20 error appears and won't go away unless I disable the comparitor. I took the comparitor and placed it in my S+ and it works ok. I measured voltages and I get the proper volts off the harness where they need to go. I have done a safe ram clear and same result. I would like some direction please as I am still learning this stuff. Thanks. The 20 error is "Coin Optics Blocked too Long"(?)
Logged
** NOTE: The information contained in any of my posts relating to slot machine ownership and use is information that I have gathered from publicly known sources correspondingly under the same protections of Free Speech governed under the Laws of the United States and Canada and is for informational use only. As is my Constitutional Right under United States and Canadian Laws the redistribution of said information is considered a form of free speech. Using this information in the United States or Canada to conduct illegal gambling in states/provinces where it is unlawful has been declared against the law in those states/jurisdictions and as such I do not advocate the illegal use of such information under both the United States and Canadian Laws. All references and examples of personal experiences are hypothetical in nature, and it is up to you to determine if the information presented is applicable to your situation or not**
a69mopar
647-402-1977
Global NLG Site Moderator
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 600
Offline Offline

Gender: Male
Posts: 3508



WWW
« Reply #1 on: November 19, 2009, 03:16:18 AM »
Hi Reho,
   The coin optic block is below the coin comparitor and has the optic board attached with 2 screws, you should disassemble this, clean the block and the prism of any blockage.  Sometimes this can be a small bit of paper, and the easy route would be to use a can of air and blow it out, although easy isn't always best.

Thanks,
Wayne
Logged
         www.GTASLOTS.com      647-402-1977              BALLY S6000 GALLERY
stayouttadabunker
Senior Full time Member.
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 1039
Offline Offline

Gender: Male
Posts: 13447
« Reply #2 on: November 19, 2009, 04:02:19 AM »
Yes, I agree...the pressurized air cans just blow stuff further INTO the machine and
into places you don't want the stuff to go to...LOL
Furthermore, if they're tilted the wrong way, out comes mist...
alcohol-based or not....water and electronics DO NOT mix!
The parts you clean with any liquid MUST be fully dried up before applying any power source.
Logged
reho33
Contributing NLG Member
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 146
Offline Offline

Gender: Male
Posts: 1594


Slot Losers of America / Tokie Owens
« Reply #3 on: November 19, 2009, 01:09:43 PM »
OK I will do this and report back
Logged
** NOTE: The information contained in any of my posts relating to slot machine ownership and use is information that I have gathered from publicly known sources correspondingly under the same protections of Free Speech governed under the Laws of the United States and Canada and is for informational use only. As is my Constitutional Right under United States and Canadian Laws the redistribution of said information is considered a form of free speech. Using this information in the United States or Canada to conduct illegal gambling in states/provinces where it is unlawful has been declared against the law in those states/jurisdictions and as such I do not advocate the illegal use of such information under both the United States and Canadian Laws. All references and examples of personal experiences are hypothetical in nature, and it is up to you to determine if the information presented is applicable to your situation or not**
jdkmunch
Senior Full time Member.
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 624
Offline Offline

Gender: Male
Posts: 2640
« Reply #4 on: November 19, 2009, 02:53:26 PM »
Just go carefully and you'll be fine.
Logged
reho33
Contributing NLG Member
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 146
Offline Offline

Gender: Male
Posts: 1594


Slot Losers of America / Tokie Owens
« Reply #5 on: November 19, 2009, 04:37:54 PM »
Munch, have you tried to remove the jumper blocks off the DS areas yet?
Logged
** NOTE: The information contained in any of my posts relating to slot machine ownership and use is information that I have gathered from publicly known sources correspondingly under the same protections of Free Speech governed under the Laws of the United States and Canada and is for informational use only. As is my Constitutional Right under United States and Canadian Laws the redistribution of said information is considered a form of free speech. Using this information in the United States or Canada to conduct illegal gambling in states/provinces where it is unlawful has been declared against the law in those states/jurisdictions and as such I do not advocate the illegal use of such information under both the United States and Canadian Laws. All references and examples of personal experiences are hypothetical in nature, and it is up to you to determine if the information presented is applicable to your situation or not**
reho33
Contributing NLG Member
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 146
Offline Offline

Gender: Male
Posts: 1594


Slot Losers of America / Tokie Owens
« Reply #6 on: November 20, 2009, 02:23:14 PM »
Well I found out why the error is there "THERE ARE NO COIN OPTICS INSTALLED IN THE MACHINE!!!!!!" just a stupid plastic block. So now I need to find that part to install.
Logged
** NOTE: The information contained in any of my posts relating to slot machine ownership and use is information that I have gathered from publicly known sources correspondingly under the same protections of Free Speech governed under the Laws of the United States and Canada and is for informational use only. As is my Constitutional Right under United States and Canadian Laws the redistribution of said information is considered a form of free speech. Using this information in the United States or Canada to conduct illegal gambling in states/provinces where it is unlawful has been declared against the law in those states/jurisdictions and as such I do not advocate the illegal use of such information under both the United States and Canadian Laws. All references and examples of personal experiences are hypothetical in nature, and it is up to you to determine if the information presented is applicable to your situation or not**
a69mopar
647-402-1977
Global NLG Site Moderator
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 600
Offline Offline

Gender: Male
Posts: 3508



WWW
« Reply #7 on: November 20, 2009, 06:00:11 PM »
Yeah, that would do it also...

W
Logged
         www.GTASLOTS.com      647-402-1977              BALLY S6000 GALLERY
jdkmunch
Senior Full time Member.
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 624
Offline Offline

Gender: Male
Posts: 2640
« Reply #8 on: November 21, 2009, 12:59:47 AM »
Did this machine have a coin head? or was it a TITO
Logged
jdkmunch
Senior Full time Member.
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 624
Offline Offline

Gender: Male
Posts: 2640
« Reply #9 on: November 21, 2009, 01:01:27 AM »
Quote from: reho33 on November 19, 2009, 04:37:54 PM
Munch, have you tried to remove the jumper blocks off the DS areas yet?

What do you mean DS? 

I can pop the jumper blocks off the MPU.  I have a board with the same plugs (non jumpers) as you
Logged
jdkmunch
Senior Full time Member.
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 624
Offline Offline

Gender: Male
Posts: 2640
« Reply #10 on: November 21, 2009, 01:06:11 AM »
DS = Dip Switches

Yes They come right off - I just need the actual jumper blocks
Logged
reho33
Contributing NLG Member
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 146
Offline Offline

Gender: Male
Posts: 1594


Slot Losers of America / Tokie Owens
« Reply #11 on: November 21, 2009, 11:34:48 PM »
The machine was TITO but I wanted to put it back to coin. So I got all the parts and the coin head is the last thing I am waiting for. But I need the optics, they are missing. GTA Slots, do you have these?
Logged
** NOTE: The information contained in any of my posts relating to slot machine ownership and use is information that I have gathered from publicly known sources correspondingly under the same protections of Free Speech governed under the Laws of the United States and Canada and is for informational use only. As is my Constitutional Right under United States and Canadian Laws the redistribution of said information is considered a form of free speech. Using this information in the United States or Canada to conduct illegal gambling in states/provinces where it is unlawful has been declared against the law in those states/jurisdictions and as such I do not advocate the illegal use of such information under both the United States and Canadian Laws. All references and examples of personal experiences are hypothetical in nature, and it is up to you to determine if the information presented is applicable to your situation or not**
a69mopar
647-402-1977
Global NLG Site Moderator
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 600
Offline Offline

Gender: Male
Posts: 3508



WWW
« Reply #12 on: November 22, 2009, 01:24:09 AM »
You would be better to get them from a U.S. vendor, I'm in Canada.  I believe Jim at Blueridge has some of these but not positive.

Thanks,
Wayne
Logged
         www.GTASLOTS.com      647-402-1977              BALLY S6000 GALLERY
Pages: [1] Go Up Print 
« previous next »
Jump to:  

SimplePortal Classic 2.0.5

If you find this site helpful, Please Consider Making a small donation to help defray the cost of hosting and bandwidth.



Newlifegames.com ™    Newlifegames.net ™    Newlifegames.org ™
   New Life Games ™    NewLifeGames ™  NLG ™ We Bring new Life to old Games ™    1-888-NLG-SLOTS ™
Are all Copyright and Trademarks of New Life Games LLC 1992 - 2021


FAIR USE NOTICE:

This site contains copyrighted material the use of which has not always been specifically authorized by the copyright owner.
We make such material available in an effort to advance awareness and understanding of the issues involved.
We believe this constitutes a fair use of any such copyrighted material as provided for in section 107 of the US Copyright Law.
In accordance with Title 17 U.S.C. Section 107, the material on this site is distributed without profit to those
who have expressed a prior interest in receiving the included information for research and educational purposes.

For more information please visit: http://www.law.cornell.edu/uscode/17/107.shtml.

If you wish to use copyrighted material from this site for purposes of your own that go beyond fair use,
you must obtain permission directly from the copyright owner.

NewLifeGames.net Web-Site is optimized for use with Fire-Fox and a minimum screen resolution of 1280x768 pixels.


Powered by SMF 1.1.20 | SMF © 2013, Simple Machines
Loon Designed by Mystica
Updated by Runic Warrior
Page created in 0.109 seconds with 19 queries.