Welcome, Guest. Please login or register.
May 18, 2024, 04:30:20 PM

Login with username, password and session length
* Home Help Arcade Login Register
.
+  Forum
|-+  **Video Slots** Gaming machines
| |-+  Aristocrat Video Gaming Machines
| | |-+  mark 5 b/v question		 0 Members and 1 Guest are viewing this topic. « previous next »
Pages: [1] Go Down Print
Author Topic: mark 5 b/v question  (Read 7314 times)
kenokarz
Contributing Gold NLG Member
NLG Member 101 to 500 Post
*

Total Karma Storms: 284
Offline Offline

Gender: Male
Posts: 470
« on: December 11, 2008, 02:18:54 AM »
i have 2 mark 5s up rights with no b/v they need gpt type assy, try the wba they dont fit does anyone have a pics of the complete assy for what i need ?? if someone has one of these machines could you please post some   Help Help
Logged
hoppy
New NLG Member 1 to 100 Post
**

Total Karma Storms: 7
Offline Offline

Gender: Male
Posts: 56
« Reply #1 on: April 30, 2009, 08:27:30 AM »
Hi .There are some MVP mk5 manuals listed on MYSLOTNOTES.COM  They may list the type used in the machine. cheers
Logged
kenokarz
Contributing Gold NLG Member
NLG Member 101 to 500 Post
*

Total Karma Storms: 284
Offline Offline

Gender: Male
Posts: 470
« Reply #2 on: April 30, 2009, 10:02:34 AM »
thanks for the info
Logged
Ozzy
Contributing Gold NLG Member
NLG Member 101 to 500 Post
*

Total Karma Storms: 254
Offline Offline

Gender: Male
Posts: 221
« Reply #3 on: April 30, 2009, 10:59:10 AM »
Here are a few pictures from a MK5 with GPT S4 bv.


cheers


O Z Z Y

* DSCN2146.jpg (97.16 KB, 640x853 - viewed 344 times.)

* DSCN2147.jpg (79.95 KB, 640x480 - viewed 297 times.)
Logged
kenokarz
Contributing Gold NLG Member
NLG Member 101 to 500 Post
*

Total Karma Storms: 284
Offline Offline

Gender: Male
Posts: 470
« Reply #4 on: April 30, 2009, 11:45:22 AM »
thanks ozzy, what are the b/v  dip settings to be for this one
Logged
Ozzy
Contributing Gold NLG Member
NLG Member 101 to 500 Post
*

Total Karma Storms: 254
Offline Offline

Gender: Male
Posts: 221
« Reply #5 on: April 30, 2009, 12:15:11 PM »
If you end up with the GPT S4 BV all switches are off (1-10)

but if you locate the earlier model switch 1 to 6 are on and 7 to 10 off.

attached is some info on the S4

MK5 also can use WBA bv if you have correct assembly frame for the machine, this would be the best way to go as the GPT software upgrades are done via a download key which is a few $$$$$, check out the web site        http://www.gptworld.com/GPT.htm.


cheers



O Z Z Y
* SA4_1.pdf (942.24 KB - downloaded 411 times.)
Logged
kenokarz
Contributing Gold NLG Member
NLG Member 101 to 500 Post
*

Total Karma Storms: 284
Offline Offline

Gender: Male
Posts: 470
« Reply #6 on: April 30, 2009, 12:39:25 PM »
what does the wba frame look like for this machine i think this would be a better way to go,
thanks as always
Logged
Ozzy
Contributing Gold NLG Member
NLG Member 101 to 500 Post
*

Total Karma Storms: 254
Offline Offline

Gender: Male
Posts: 221
« Reply #7 on: April 30, 2009, 01:20:02 PM »
Never seen one as all my Aristocrats have the GPT S4, but would imagine it would be this (attachment) you would need to also get hold of the Bill Entry for the door panel and the correct harness.


cheers


O Z Z Y
* wba.pdf (7.5 KB - downloaded 186 times.)
« Last Edit: April 30, 2009, 01:28:08 PM by Ozzy » Logged
Op-Bell
Contributing Gold NLG Member
Sr.NLG Member 501 to 1000 Post
*

Total Karma Storms: 326
Offline Offline

Gender: Male
Posts: 854
« Reply #8 on: May 01, 2009, 05:06:36 AM »
WBA frame is basically two flat plates with spacers at the top and bottom. Not hard to fabricate yourself. However, you would need a few extra parts to make it a full GPT replacement, like the JCM 'G-Pattern Bezel' and a JCM 300-100037 board and harness set. Best to stick with the GPT unless you can pick the WBA kit up as a lot.

<edit> and if you had the hopper shown in Ozzy's picture above, you'd have to work on the bowl, because the WBA needs a cutout about 2 inches deeper. The bowl is ABS and can be softened with a heat gun and bent by hand.
Logged
kenokarz
Contributing Gold NLG Member
NLG Member 101 to 500 Post
*

Total Karma Storms: 284
Offline Offline

Gender: Male
Posts: 470
« Reply #9 on: May 01, 2009, 11:14:12 AM »
thanks i will try that,if anyone has a pic of a mark 5 with the wba please post, mine does not have a b/v no cage or anything
bought as a parts machine and this is my next project to build, the only thing im misssing is the b/v parts
Logged
Pages: [1] Go Up Print 
« previous next »
Jump to:  

SimplePortal Classic 2.0.5

If you find this site helpful, Please Consider Making a small donation to help defray the cost of hosting and bandwidth.



Newlifegames.com ™    Newlifegames.net ™    Newlifegames.org ™
   New Life Games ™    NewLifeGames ™  NLG ™ We Bring new Life to old Games ™    1-888-NLG-SLOTS ™
Are all Copyright and Trademarks of New Life Games LLC 1992 - 2021


FAIR USE NOTICE:

This site contains copyrighted material the use of which has not always been specifically authorized by the copyright owner.
We make such material available in an effort to advance awareness and understanding of the issues involved.
We believe this constitutes a fair use of any such copyrighted material as provided for in section 107 of the US Copyright Law.
In accordance with Title 17 U.S.C. Section 107, the material on this site is distributed without profit to those
who have expressed a prior interest in receiving the included information for research and educational purposes.

For more information please visit: http://www.law.cornell.edu/uscode/17/107.shtml.

If you wish to use copyrighted material from this site for purposes of your own that go beyond fair use,
you must obtain permission directly from the copyright owner.

NewLifeGames.net Web-Site is optimized for use with Fire-Fox and a minimum screen resolution of 1280x768 pixels.


Powered by SMF 1.1.20 | SMF © 2013, Simple Machines
Loon Designed by Mystica
Updated by Runic Warrior
Page created in 0.091 seconds with 19 queries.