Typical home use settings for the SP1271 family of S+ game chips
StatFreak:
SP1271 family of game chips: Typical setup for home use.
Important: All setting changes require 0 credits on the machine before entering setup mode.
[*]With the machine turned on and in idle mode, open the door press the white test button 2 times
[*]You should see "2 n" in the winner paid/credits windows, where n= 0 or 1. Press the spin button until it reads "2 1”
This enables the spin sounds.
[*]Turn the jackpot key once. This advances through the setup sub-menu
[*]You should see "5 n" in the window, where n= 0 to 2. Press the spin button until it reads "5 0"
This will make all wins automatically go to the credit meter. You will not have to turn on the credit button before playing.
[*]Turn the jackpot key three times.
[*]You should see "8 n" in the window, where n= 0 to 2. Press the spin button until it reads "8 1"
This will force all bills inserted to go to the credit meter. You will never accidentally end up cashing out your bill.
[ADD 5-30-2011] It turns out that this setting has to be enabled when the dbv is set up using the SET chip. If the SET chip option is
configured as disabled, this option can't be changed and all bills will always go to the tray. If the SET chip option is configured as enabled,
then the option is set here. If enabled, a set chip is NOT required to change this setting.
Thanks Poppo and Stayouttadabunker for this info. :3-
:259-
[*]Turn the jackpot key once
[*]Press the white test button to "return" to the main menu and advance through it until you get to option group 7
{stop the first time you see a “7” in the Coins-In display}
[*]Set your hopper and credit limits as follows:
Note: To set these values, turn the jackpot reset key to change the selected (flashing) digit. Press the spin button to increment the
flashing digit.
[o][7-1] 0000 Maximum number of credits that will actually cash out from your hopper.
Zero effectively disables the hopper, but you can use a low number to match the number of coins that you have, if you wish.
If you have more credits than the value set here on the meter, pressing cash out will become a hand pay that is cleared with
the key.
[o][7-2] 1200 This will cause all single wins of 1201 or more to lock up as a jackpot with lights flashing. Set this between the highest win that you
want to pay out normally and the lowest win that you want to lock up as a jackpot. Jackpot wins cleared with the jp key
"disappear" and are not added to the credit meter (although they are added to the jackpot meter in the bookkeeping menus.)
[o][7-3] 9999 All single wins of equal to or less than the value set in [7-2] (1200 or less in this case) will go to the credit meter as long as the final
number of credits is less than 10,000.
[o][7-5] 2000 The bill validator will turn off when you have more than 2000 credits. Use any value that you want here.
[o][8] 0000 optional. Partial pay on lockups. If you want some of your jackpot or lockup amounts to pay from the hopper, set this
to the number of coins you want to pay out. This number cannot be higher than the hopper limit setting [7-1].
[*]Press the white test button one final time after making your last setting change to be sure that the changes stick
[*]Close the door
[/list]
coorslight115:
Nice post Stat !! :3- :3- :3-
Should help a few
:259-
twizz63:
That is great info stat...I am fairly new at this. Would it be similar for a double spin DD? My chip says s-plus SP810 Type 20 . Also has 1-512 AZ1. I am confused and cannot figure it out. Thanks :279-
StatFreak:
Quote from: twizz63 on May 02, 2011, 05:33:25 AM
That is great info stat...I am fairly new at this. Would it be similar for a double spin DD? My chip says s-plus SP810 Type 20 . Also has 1-512 AZ1. I am confused and cannot figure it out. Thanks :279-
The older family of chips do not allow for separate hopper, credit, and jackpot limits, so you can't run "coinless."
Your hopper limit, jackpot limit, and credit limit are the same (one setting), so all credits on the meter will be paid in coins from the hopper anytime you press the cashout button and all wins over your set limit will be jackpot lockups. Partial pays and separate DBV cutoff settings can still be set. To enable partial pays, you will need to set option "34 n" in the options setup group to 1. If turned on, you will then see page [8] in the main menu.
Your MPU board switches affect your settings (unlike the 1271 which doesn't use them). Turn on Switches 1-3 and turn off 4-8. Switches 1 and 2 set your hopper limit, and turning them both on will allow you to set the limit in the software under setting 7 instead of having a "hard coded" limit imposed. Switch 3 turns on your spin sounds. There is no setup option "2 n" for sound in the menu.
twizz63:
Thanks Stat, I am sure that will help. My problem is machine locking up for handpay. I think I have DIP 's figured out....just need to increase hopper limit.
Navigation
[0] Message Index
[#] Next page