Mikohn Progressive Controllers Displays and other info |
<< < (2/178) > >> |
Thor777: belbenchtech Belbenchtech's Repair Logs Moderator. NLG Member 101 to 500 Post Members Rating: 109 [Good Karma] [Bad Karma] Offline Posts: 304 Belbenchtechs Repair Logs. Re: Mikohn Progressive Controllers Displays and other info « Reply #6 on: November 13, 2005, 04:19:25 AM » -------------------------------------------------------------------------------- Mikohn Error Codes (pre-1998); There are two general categories of error codes; Display & Controller. Display error codes; C1 Display has lost communication with controller. Perhaps a broken wire or unplugged. C2 Current value too long for display. Parameters incorrectly set. C3 Verify error on data written to RAM on LED logic. Jackfile too long? C4 PROM limit overflow. (Jackpot value exceeds fixed limit in PROM.) Error in current jackpot value? (Too many digits/symbols.) Controller error codes; $C.10 Controller checksum failure. Usually associated with stand-alone or slave component. $C.11 Bad reception. (Over 20 over-run framing errors.) Usually caused by loose fiber connector. $C.30 Slave controller does not detect master controller. Improper switch setting on controller? $C.31 Slave polled but not acknowledged (more than 20 failures). Error in fiber system. Check all fibers. *from Mikohn Technical Bulletin Vol. 1, No. 1 |
Thor777: hotslot101 Guest Re: Mikohn Progressive Controllers Displays and other info « Reply #7 on: November 13, 2005, 12:55:27 PM » -------------------------------------------------------------------------------- Code Description C1 Communication loss controller to display C2 Value too long for display on current programmed JP C3 Test pattern written to RAM on logic when read back has been corrupted C4 PROM limit overflow. The current jp value exceeds the fixed limit value in the EPROM C8 Sentinel Timeout (CHAMII, v3.02 only) C9 Loss of configuration (CHAMII only) C10 Checksum of a value in the controller has failed CHAMII+ DISPLAY ERROR CODES Code Description C1 Communication Link is down C2 Metered Amount is too large to fit in window C5 In MultiLink mode: Jackpot Token is not set to 8 in JPOT.DO file (PSP Message Programming) C10 Progressive is not set up (use PSP to initialize progressive) C12 Current Amount is greater than Limit C14 The selected Machine Serial setting is not supported C15 Progressive not set up correctly (Base>Limit or Base>Current or Hidden>Limit) C52 In MS10 Machine Serial setting: A serial machine has gone off-line CON2 CONTROLLER ERROR CODES Code Description C11 Fiber bus communication error in the UART. Over 20 errors have been received from the fiber bus C12 Programmed JP limit is less than current JP C13 Over 20 errors have been received from the Tandy 102 or other laptop C14 Slot machine interface communication error in UART. Over 20 errors have been received from the slot machine interface C15 Power up JP limit failure C16 Power brown-out C17 RAM signature error C18 Hidden JP (Minimum Value) is equal to or greater than the JP limit (Maximum Value) C19 Current JP is greater than the JP limit (Maximum Value) C20 Random Jackpot System Only – Coin-in Buffer C21 Digit overflow C30 Slave controller does not detect a master controller C31 Slave being polled but has not been acknowledged after 20 retries C32 Slave resend RAM failure C33 Slave has ACK’d more coins than possible C34 Master’s fiber pass through has failed after three attempts C50 MULTI-COM is not responding C51 Transmission/reception failure C52 Serial Transmission/reception failure C53 Serial machine Mystery Pay is not available C54 Bally MultiComm error: Bad CRC C55 Bally MultiComm error: Non BCD value C56 Bally MultiComm error: Invalid group ID C58 Bally MultiComm error: Wrong sequence number C59 Bally MultiComm error: Invalid machine ID C60 Event driven bonus not available. C61 Event driven bonus Threshold value is 0 C77 Database error C80 Slave controller does not detect a master present on a Random Bonus game C81 Slave coin buffer overflow C82 Random coin matrix buffer overflow C83 Random coin buffer overflow C84 Denomination multiplier overflow SUPERLINK V1.63 AND NEWER ERROR CODES Code Description C10 RAM failure is caused by bad checksum or wrong data type C11 Fiber port serial error C12 Jackpot group limit error: Current >Limit C13 Programming port serial error C14 Serial machine port serial error C15 Power-up limit failure C16 Power failure C17 RAM signature failure: Causes complete factory reset C18 Jackpot group limit error: Minimum exceeds Limit C19 Jackpot group limit error: Random C20 Random coin-in buffer error: Non-BCD value C21 Digit overflows: a result was larger than 10 digits C22 Battery backup data recovered ok C23 Payout amount does not exist in pay-table C24 Pay-table is invalid: Payout weights do not add up to 100% C25 Increment value is too large: Value> 0.100 000 00 C26 Machine denomination mismatch C29 Controller’s password has been expired C30 Fiber time-out: Slave has not been polled C31 Fiber time-out: Slave has not been acknowledged C32 Slave re-sends RAM failure: Bad checksum or wrong data type C33 Slave has acknowledged more coins than possible C34 Master’s fiber pass through has failed after 3 attempts C35 SIB power-up reset C36 SIB false jackpot C37 SIB false jackpot canceled C40 Merchandise controller: Bonus mode is active C41 Merchandise controller: Bonus mode is inactive C42 DCU controller: Jackpot queue is overflow, clear jackpot queue C50 Bally MultiComm time-out: MultiComm not responding to poll C51 No serial machine is on-line C52 Serial machine or SIB has gone off-line C53 Serial machine Mystery Pay is not available C54 Bally MultiComm error: Bad CRC C55 Bally MultiComm error: Non BCD value C56 Bally MultiComm error: Coin buffer overflows C57 Bally MultiComm error: Invalid group identifier C58 Bally MultiComm error: Wrong sequence number C59 Bally MultiComm error: Invalid machine number C60 Gaming Device: General Tilt C61 Gaming Device: Power Up Reset or Game Reset C62 Gaming Device: Coin In Error C63 Gaming Device: Coin Out Error C64 Gaming Device: Game RAM or EPROM Error C65 Gaming Device: Bill Validator Error C66 Gaming Device: Hopper Empty or Hopper Error C67 Gaming Device: Reel Tilt C68 Gaming Device: Reset During Payout C70 Gaming Device: Game Door Open C17 Gaming Device: Game Door Close C72 Gaming Device: Drop Door Open C73 Gaming Device: Drop Door Close C74 Gaming Device: Bill Door Open C75 Gaming Device: Bill Door Close C77 Machine ID RAM failure: bad checksum or wrong data type C80 Slave indicates no response from master C81 Slave coin-in buffer overflows C82 Random coin-in matrix overflows: more than 99 coins C83 Random coin-in buffer overflows: more than 9999 coins C84 Denomination multiplier overflows: result > 9999 C90 Single/Multi-Link: Controller mode is corrupted. C91 Single/Multi-Link: Jackpot Group number is out of range C92 Single/Multi-Link: Duplicated machine number C93 Single/Multi-Link:Link Number is out of range C94 Multi – Site: Jackpot coin-in contribution is already reported C95 Communication between SIB - - Gaming Machine is off C96 Communication between SIB - - Gaming Machine is on C97 Communication between Controller – SIB is off C98 Communication between Controller – SIB is on C99 Auto-Polling Error: Coin-in values lower than previous poll Cheers Ozzy |
Thor777: hotslot101 Guest Re: Mikohn Progressive Controllers Displays and other info « Reply #9 on: November 13, 2005, 03:07:13 PM » -------------------------------------------------------------------------------- You are very welcome................................that's what this site is about, sharing knowledge I hope, without the consequences if you know what I mean...............................................................keep posting cheers Ozzy Report to moderator Logged belbenchtech Belbenchtech's Repair Logs Moderator. NLG Member 101 to 500 Post Members Rating: 109 [Good Karma] [Bad Karma] Offline Posts: 304 Belbenchtechs Repair Logs. Re: Mikohn Progressive Controllers Displays and other info « Reply #8 on: November 13, 2005, 01:58:44 PM » -------------------------------------------------------------------------------- Ozzy, Thanks for the information...it is greatly appreciated! Mike><> |
Thor777: hotslot101 Guest Re: Mikohn Progressive Controllers Displays and other info « Reply #10 on: November 13, 2005, 03:38:59 PM » -------------------------------------------------------------------------------- Quote from: Jay on November 11, 2005, 09:34:20 PM I just got a Mikon Controller and display - the device reads EMPTY on the screen. I hooked up a 9pin straight through Male to Female cable from the laptop and ran the PSP 2.0 program. Depending on which controller I choose (Con1, Con2, Old) I get a communication error. What am I doing wrong ? Check your Chameleon driver PCB setting, A0/A1 etc etc. |
Thor777: dngrs1 NLG Member 101 to 500 Post Members Rating: 22 [Good Karma] [Bad Karma] Offline Posts: 127 Re: Mikohn Progressive Controllers Displays and other info « Reply #11 on: November 14, 2005, 01:48:18 AM » -------------------------------------------------------------------------------- Picture posts per Joey---- First Photo: 1X2 Overhead Sign Driver Board Second Photo: 32 Machine CON1 Third Photo: CHAM1 /LED5 Driver Board Descriptions added by CJ -------------------------------------------------------------------------------- |
Navigation |
Message Index |
Next page |
Previous page |