Welcome, Guest. Please login or register.
May 19, 2024, 04:26:55 PM

Login with username, password and session length
* Home Help Arcade Login Register
.
+  Forum
|-+  **Reel Slots** Gaming Machines
| |-+  WMS Reel Games. (Moderator: knagl)
| | |-+  WMS Jackpot Stampede problem		 0 Members and 1 Guest are viewing this topic. « previous next »
Pages: [1] Go Down Print
Author Topic: WMS Jackpot Stampede problem  (Read 7626 times)
Nixs
New NLG Member 1 to 100 Post
**

Total Karma Storms: 0
Offline Offline

Posts: 30
« on: January 25, 2013, 03:13:47 PM »
i have had this for years and really never worked,replaced the power supply(which was bad for sure) it did work every once in a while
replaced the i/o with brand new board,when i turn the game on it bongs once and goes to the tilt light by the coins display
the display shows no error code only the tilt light stays on
tried pushing the red button inside and does nothing the lock on side does nothing either
anybody know what is going on with it:)

thanks!!! Nick

this is just the reel version no display on top
Logged
Nixs
New NLG Member 1 to 100 Post
**

Total Karma Storms: 0
Offline Offline

Posts: 30
« Reply #1 on: January 25, 2013, 03:20:19 PM »
i have had this for years and really never worked,replaced the power supply(which was bad for sure) it did work every once in a while
replaced the i/o with brand new board,when i turn the game on it bongs once and goes to the tilt light by the coins display
the display shows no error code only the tilt light stays on
tried pushing the red button inside and does nothing the lock on side does nothing either
anybody know what is going on with it:)

thanks!!! Nick

this is just the reel version no display on top
Logged
knagl
Global NLG Site Moderator
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 642
Offline Offline

Gender: Male
Posts: 5489


Kevin
« Reply #2 on: January 25, 2013, 04:54:24 PM »
Are all of the voltage LEDs lit up on the circuit board inside the card cage?
Logged
If you find this site helpful, please consider making a small donation to help defray the cost of hosting and bandwidth.

Please do not PM me for support or "how to" requests -- please post your request in the forum so that everyone may assist you and everyone can benefit from the answer to your question!  Thanks! Smiley
Nixs
New NLG Member 1 to 100 Post
**

Total Karma Storms: 0
Offline Offline

Posts: 30
« Reply #3 on: January 25, 2013, 05:11:37 PM »
yep all lights on for voltages and the error light on the left
i tried reseeding the boards also
Logged
knagl
Global NLG Site Moderator
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 642
Offline Offline

Gender: Male
Posts: 5489


Kevin
« Reply #4 on: January 26, 2013, 08:05:56 AM »
Hmm. Maybe reseat the chips on the board, too? Do you have any other chip sets to try? That's frustrating that it's not really giving you an error message.
Logged
If you find this site helpful, please consider making a small donation to help defray the cost of hosting and bandwidth.

Please do not PM me for support or "how to" requests -- please post your request in the forum so that everyone may assist you and everyone can benefit from the answer to your question!  Thanks! Smiley
Nixs
New NLG Member 1 to 100 Post
**

Total Karma Storms: 0
Offline Offline

Posts: 30
« Reply #5 on: January 27, 2013, 04:48:12 PM »
tried same results
Logged
Neonkiss
Contributing Gold NLG Member
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 436
Offline Offline

Gender: Male
Posts: 2084
« Reply #6 on: January 27, 2013, 05:01:19 PM »
Could be the CPU.
Just tested 4 CPU's for anothe member here and three were bad.
Also do you know for sure the I/O is good? was ot verfied in another machine?
Logged
Nothing brings people together better than a common enemy
343 / 60 brothers lost on that day.
Nixs
New NLG Member 1 to 100 Post
**

Total Karma Storms: 0
Offline Offline

Posts: 30
« Reply #7 on: January 27, 2013, 05:17:53 PM »
yep
i/o was good have 2 of them,1 tested good for sure the other was the one that came in the machine so not sure about it
Logged
Neonkiss
Contributing Gold NLG Member
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 436
Offline Offline

Gender: Male
Posts: 2084
« Reply #8 on: January 27, 2013, 08:45:53 PM »
Quote from: Nixs on January 27, 2013, 05:17:53 PM
yep
i/o was good have 2 of them,1 tested good for sure the other was the one that came in the machine so not sure about it
Then I would start with the CPU.
Logged
Nothing brings people together better than a common enemy
343 / 60 brothers lost on that day.
Nixs
New NLG Member 1 to 100 Post
**

Total Karma Storms: 0
Offline Offline

Posts: 30
« Reply #9 on: January 27, 2013, 08:57:57 PM »
which part is that on the board?
Logged
Neonkiss
Contributing Gold NLG Member
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 436
Offline Offline

Gender: Male
Posts: 2084
« Reply #10 on: January 27, 2013, 09:05:09 PM »
The machine has two boards in the card cage located inside the machine just above the hopper.
The upper board is the I/O board and handles all the outputs for the machine
and the lower board is the CPU and runs the programs for the machine.

If you have a bad CPU it can cause the fail led to illuminate on the I/O board.
That is if you absolutely know that the I/O board is good
Logged
Nothing brings people together better than a common enemy
343 / 60 brothers lost on that day.
Nixs
New NLG Member 1 to 100 Post
**

Total Karma Storms: 0
Offline Offline

Posts: 30
« Reply #11 on: January 27, 2013, 09:39:31 PM »
can i replace the chip or need another board?
if i get another board will i have to program it  with a special chip or can i just put the chips on it
Logged
Neonkiss
Contributing Gold NLG Member
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 436
Offline Offline

Gender: Male
Posts: 2084
« Reply #12 on: January 28, 2013, 09:38:52 AM »
If you try another board you can swap your chips to the new board.
But you will need a RAM clear XU-3 chip in the denomination of the machine.
If it going to be a nickel machine, then that is a differant RAM clear chip than the one used for a quarter machine.
Logged
Nothing brings people together better than a common enemy
343 / 60 brothers lost on that day.
Nixs
New NLG Member 1 to 100 Post
**

Total Karma Storms: 0
Offline Offline

Posts: 30
« Reply #13 on: January 31, 2013, 05:24:46 PM »
ok rplaced the entire board and swapped the chips same problem
i did notice the 2nd pin on one of the chips was bent,fixed it it
same tilt lights up and no codes

do i need to get a clear chip for this of a new set of chips
does anybody have any?

thanks!!!
Logged
Neonkiss
Contributing Gold NLG Member
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 436
Offline Offline

Gender: Male
Posts: 2084
« Reply #14 on: January 31, 2013, 07:33:19 PM »
No, a clear will not do anything for you at this point.
Since you tried the I/O and the CPU, I'm not sure what else it could be.
I still believe the issue is with one of those boards. If you send me a PM I'll let you know what it will cost for me to check them out and let you know the status of the boards you purchased. Or if it was from a vender, maybe call him to tell them what the boards are doing in your machine.
Logged
Nothing brings people together better than a common enemy
343 / 60 brothers lost on that day.
KirkLasVegas
Retired OLD Buzzard
Contributing Gold NLG Member
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 233
Offline Offline

Gender: Male
Posts: 1104


Newest addition to the family, RIP Bentley
« Reply #15 on: January 31, 2013, 08:24:31 PM »
Seen this before, check/replace the socket for XU-3 on the MPU board.
People go to clear the machine, they get bad data and it writes shit to the EEPROM.
If he gets good lites on the MPU, a single bonk and nothing the MPU is not running...
Even better, install a low profile ZIF socket there or a quality roundpin socket like a Augat.

Kirk
Logged
Definition of "Retirement"= to be able to get back all you contributed into it AND take some of their money too before dropping dead.
Neonkiss
Contributing Gold NLG Member
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 436
Offline Offline

Gender: Male
Posts: 2084
« Reply #16 on: January 31, 2013, 11:05:54 PM »
Quote from: Nixs on January 25, 2013, 05:11:37 PM
yep all lights on for voltages and the error light on the left
i tried reseeding the boards also
Quote from: KirkLasVegas on January 31, 2013, 08:24:31 PM
Seen this before, check/replace the socket for XU-3 on the MPU board.
People go to clear the machine, they get bad data and it writes shit to the EEPROM.
If he gets good lites on the MPU, a single bonk and nothing the MPU is not running...
Even better, install a low profile ZIF socket there or a quality roundpin socket like a Augat.

Kirk

Kirk, you might be on to something but I still think he has a bad board somewhere since he said he also has the fail light illuminated.

Quote from: Nixs on January 25, 2013, 05:11:37 PM
yep all lights on for voltages and the error light on the left
i tried reseeding the boards also

Also I sent you a PM about the run-a-way hopper syndrome you had before. Can you shed some light?
Logged
Nothing brings people together better than a common enemy
343 / 60 brothers lost on that day.
Nixs
New NLG Member 1 to 100 Post
**

Total Karma Storms: 0
Offline Offline

Posts: 30
« Reply #17 on: January 31, 2013, 11:07:43 PM »
replaced the old board with a brand new one same thing but fail light comes on after the bong now instead of when plugged in
Logged
Pages: [1] Go Up Print 
« previous next »
Jump to:  

SimplePortal Classic 2.0.5

If you find this site helpful, Please Consider Making a small donation to help defray the cost of hosting and bandwidth.



Newlifegames.com ™    Newlifegames.net ™    Newlifegames.org ™
   New Life Games ™    NewLifeGames ™  NLG ™ We Bring new Life to old Games ™    1-888-NLG-SLOTS ™
Are all Copyright and Trademarks of New Life Games LLC 1992 - 2021


FAIR USE NOTICE:

This site contains copyrighted material the use of which has not always been specifically authorized by the copyright owner.
We make such material available in an effort to advance awareness and understanding of the issues involved.
We believe this constitutes a fair use of any such copyrighted material as provided for in section 107 of the US Copyright Law.
In accordance with Title 17 U.S.C. Section 107, the material on this site is distributed without profit to those
who have expressed a prior interest in receiving the included information for research and educational purposes.

For more information please visit: http://www.law.cornell.edu/uscode/17/107.shtml.

If you wish to use copyrighted material from this site for purposes of your own that go beyond fair use,
you must obtain permission directly from the copyright owner.

NewLifeGames.net Web-Site is optimized for use with Fire-Fox and a minimum screen resolution of 1280x768 pixels.


Powered by SMF 1.1.20 | SMF © 2013, Simple Machines
Loon Designed by Mystica
Updated by Runic Warrior
Page created in 0.169 seconds with 20 queries.