New Life Games Tech Forums

Anybody have one for sale? Blueridge?

Ron (r273)

I bet if you sweet talked bunker, he'd gladly make you one  :279-

I think Bunker was  :8- the last time he fooled with the micro

lol...Microfit connectors yeah - I hate those...
This one's easy though.
I'll make ASAP
Gimme your home address r273...the right one this time....lol
I'll let you know in the morning if I have the black Molex.

I just checked my stash of connectors r273...
unfortunately I don't have those... :37-
You want me to order some?

Sure....PM me the price to make two. Will paypal you.

Ron (273)

How about if I just hypnotize you.... :96-


( :122-                                                    :122- )
                               
                                       :122-

                   :122-                           :122-
                           :122-  :122- :122-
       



I'll find out some prices for the parts and stuff and let you know in a bit r273!
I gotta check out some websites for the connectors and pins...

I will put those signs at my bar along with "FREE BEER TOMMORRO"   :222-   :72-

Okay guys,
I had a little bit of difficulty finding that old 7 segment thread
because Laneman wanted one of these also.
Anyways, the mouser order for these parts I've just placed and should
be getting them in next week sometime....
I'll keep you guys updated.

I guess I know what I'm doing this afternoon... :72-
Some parts came in from mouser last night! >>>

Okay,
I stripped 12 wires, dipped them soldered them to 12 receptor pins.
They were inserted into the housing with the tabs facing up towards the housing latch tab.
The green wire is the pin#1.
The blue wire on that same line is #6 and opposite the blue wire is pin #12.
The yellow wire opposite the lone green #1 wire is pin#7.
I hope you gave me the correct pin-outs! lol

Attached below is the drawing from Molex of the pin locations on the housing.
It is essential that they match the pin-outs Laneman posted in this below...
This is NOT a straight through pin-out set-up!
Click to enlarge! >>>

Okay,
The other end of the wires were stripped and tinned and soldered into the male pins.
The just need to be hand crimped with my cheap %$#@ $5 dollar jewelry
hand crimp because a crimper costs like $500.00 bucks - which I don't have...lol
Then these babies will be ready to be inserted into the 12-pin Molex housing!

At this point - the pin-outs better be right or these are a mother&%$#@ to get back out!  :72-

Click to enlarge! >>>

Does this mean the cost on these went sky high?  :72-

Of course you know you can name your price. :131-

Ron (r273)

  :97- :208- :72- No...!
You're lucky I like you! lol
I'm guessing I spent about $8 bucks on parts and a small packing envelope.
You owe me about $600.00 dollars!  :96-

Nah...Twenty okay? You can Paypal me, send me a brand new spanking bill
in an envelope or fix my transmission on my Subaru...lol

Okay! I finished the 7-Segment Micro Harness!! :136-
This shiny puppy just rolled off the line...
It might even have my DNA on it....lol
Now I gotta make another one 'cause you wanted two of them! ARGHHHHhhh!  :96-
Click on the photo to enlarge! >>>

Thank you, thank you!  :131- :3- :131- :3- :244-

lol...got your PM...
I will try to mail them out to you tomorrow ....lol
'bama right? Not TX? lol

I have enough parts to make one more...
Laneman! You still need one?

Not TX. or GA.  :72-
 You can keep the quarter for a tip and I don't need the little screw driver cauz it's not bent.  :200-

Ron (r273)

Mark I got the micro harnesses today. Thank you again. They work!...................well almost.  The touch denom flashes around the amounts
but does not change the denom when touched. It stays on the default amount. I assume it might be the game (Double Hearts SB000092).
Have not had time to change the game yet. Have set the amounts and percentages for each, using VS011GX1 and SG000363. I have tried
3 different multi- touch boxes and they all do the same.

Any thoughts?

Ron (r273)

You're asking me? lol
I don't have one of these things.
I wish I knew how to set one up but I don't have any
information on these multi-denomination touchscreens unfortunately.
However, I did find this excerpt from the SG000363 PSR sheet.

I think you're gonna need an SB00092 PSR sheet for more info...
If you get a copy - please pass it my way? Thanks!
Click to enlarge... >>>