|
Title: help with "reel 1 tilt" Post by: cristiancerneschi on January 26, 2011, 08:53:57 AM hello,
I'm new here and I already start to ask help:)) I have a S2000 reel touch with this error : reel 1 tilt. the reel is really dead. the rest, 2, 3 ,4 ,5 seems to be ok. I try everythig. change the reel in position 2, it's activated. the one from position 2 on position 1 is dead. I chech the wire, ok. I swich the controler, nothing. any ideea??? thank you very much Title: Re: help with "reel 1 tilt" Post by: poppo on January 26, 2011, 01:09:22 PM I'm not a S2000 expert, but if you have eliminated the reel as being bad by swapping them, and changed the MPU, all that really leaves is the wiring or the motherboard. I would double check the wiring. Make sure no pins are coming out of the plugs on both ends. Also make sure a wire didn't get cut/broken somewhere in between.
Did it work before and just quit, or did you get it this way? Title: Re: help with "reel 1 tilt" Post by: stayouttadabunker on January 26, 2011, 01:17:27 PM When you turn on the power with the door open,
are the reels "stiff"? Try turning the reels one by one with your finger and please tell us the difference, in resistance, between the 1st reel and the others. Does the 1st reel work correctly when you swap it with the 2nd position on the reel shelf? Or the does the error change to "Reel 2" error on the display? When you say you switched "controller" - what part are you talking about? Title: Re: help with "reel 1 tilt" Post by: poppo on January 26, 2011, 01:24:31 PM Does the 1st reel work correctly when you swap it with the 2nd position on the reel shelf? Or the does the error change to "Reel 2" error on the display? He said the problem stayed with reel #1, (and reel #1 worked in pos #2). At least that's how I read it. Title: Re: help with "reel 1 tilt" Post by: stayouttadabunker on January 26, 2011, 01:30:19 PM Okay good,
Does the 2nd reel unit work when installed into the 1st position on the reel shelf? I'm suspecting it's nothing more than an oxidized pin in the 1st reel Molex connector. Or a bent pin? Title: Re: help with "reel 1 tilt" Post by: poppo on January 26, 2011, 01:35:39 PM Okay good, Does the 2nd reel unit work when installed into the 1st position on the reel shelf? :209- " the one from position 2 on position 1 is dead" :96- But I agree he needs to look closer at the wiring/connectors. Title: Re: help with "reel 1 tilt" Post by: cristiancerneschi on January 27, 2011, 08:27:27 AM thank you all for your support.
the problem is on MPU. I was letting that possibility the last because I don't have a spare one. as per my casino owner: "is not good spending money for spare parts. better pray nothing bad happen" :208- and as per law in romania I have a seal for every MPU, and that mean when I use the MPU from another machine I must keep it close for 2-3 weeks untilt somebody from gaming board come to put me another seal. now I must send the MPU in holland, to the IGT europa for repair. thank you very much again. cristian Title: Re: help with "reel 1 tilt" Post by: stayouttadabunker on January 27, 2011, 12:29:51 PM I'd tell your cheapskate boss to cough up some money for spare parts!!!! :72-
|