|
Title: 8724 back from the dead Post by: waltervan on February 10, 2011, 10:29:44 PM I just changed the battery in the access board and the machine fired up.
Is there any way to set this up for free play if not how hard is it to convert it to a token machine? How do i set this machine up are the games I see the only games or are there a list of games I can chose from? I am a total Nub to all of this any hints or tricks yall may know would help Thanks Title: Re: 8724 back from the dead Post by: knagl on February 10, 2011, 10:52:07 PM There is a demo mode, but you can only access that immediately after a clear. Once the machine has been "enrolled" for coin/bill use on a casino floor, it can't be reverted to the demo mode without the use of a clear (zero) chip.
Assuming you have a coin comparator in there, you should be able to replace the sample coin in there with a token and use tokens in your machine. If it's a quarter machine, be sure to use quarter sized (or close) tokens so the hopper will be able to correctly dispense them. It's been a while, but to get to the game setup section you'll need to have ALL of the access doors open. Open the belly door, the top door, AND slide out the logic drawer halfway or so. Then, turn the jackpot reset key, and sections of the menu that would previously give you a "Not Authorized" error will be more accessable. It does depend on your software as to whether or not you'll be able to change the games. On my old machine (which I no longer have) I was unable to make any changes to the available games when the game was enrolled. I've seen others, however, that would allow you to change which games were available. Title: Re: 8724 back from the dead Post by: waltervan on February 14, 2011, 01:53:04 AM The coin mech I have dose not have a sample coin in it. The best I can tell the mech has to be programed to take coins and mine is programed for .01, .05, .25 but not tokens and I have been unable to find any one to change it. I cant find the wiring harness to go from the type of the mech that has a sample coin to a board not sure what it is but its labeled Multi Coin Mech the mech I have is wired to the vertical plug with the clamps and the harness I need is the one on J73. Any ides where I could get one???
(http://newlifegames.net/nlg/index.php?action=dlattach;topic=3879.0;attach=10999;image) Title: Re: 8724 back from the dead Post by: rickh on February 14, 2011, 11:11:46 AM I have a dead VLC ... wonder if I have a part in it you need? See my machine in earlier posts in this section.
Title: Re: 8724 back from the dead Post by: rilaw on February 19, 2011, 09:13:05 PM The coin mech I have dose not have a sample coin in it. The best I can tell the mech has to be programed to take coins and mine is programed for .01, .05, .25 but not tokens and I have been unable to find any one to change it. I cant find the wiring harness to go from the type of the mech that has a sample coin to a board not sure what it is but its labeled Multi Coin Mech the mech I have is wired to the vertical plug with the clamps and the harness I need is the one on J73. Any ides where I could get one??? (http://newlifegames.net/nlg/index.php?action=dlattach;topic=3879.0;attach=10999;image) Could you post a pic of your coin mech? The pic of the board you posted shows that you have the wire that goes to the coin mech or cc plugged in? Title: Re: 8724 back from the dead Post by: waltervan on February 19, 2011, 10:40:37 PM The pic i posted shows the wire i need. Its one i found here on another post. It looks like rick might have what I am looking for ill post back if it works.
Title: Re: 8724 back from the dead Post by: rilaw on February 19, 2011, 10:43:41 PM The pic i posted shows the wire i need. Its one i found here on another post. It looks like rick might have what I am looking for ill post back if it works. Sorry, thought that was your machine. Good luck! Title: Re: 8724 back from the dead Post by: rickh on February 19, 2011, 11:23:56 PM I will be removing and shipping it this week.. hope it works. Who else needs guts from this machine, we are gonna shoot it up soon :)
Title: Re: 8724 back from the dead Post by: joshmail on February 20, 2011, 01:55:55 AM we are gonna shoot it up soon :) Can I come, i'd love to shoot up a slot! Just not mine! Title: Re: 8724 back from the dead Post by: rickh on February 20, 2011, 01:59:33 AM maybe I will video it and put the shoot out here for all to see.....
Title: Re: 8724 back from the dead Post by: joshmail on February 20, 2011, 02:06:39 AM Just let me know, I have a AK with a hunger for slots.........
Title: Re: 8724 back from the dead Post by: rickh on February 20, 2011, 03:27:45 AM lets find a local place to take it and have some fun.. just gotta gut it first.
Title: Re: 8724 back from the dead Post by: joshmail on February 20, 2011, 04:42:46 AM I never had a problem at Flat Iron Mt. let's BBQ I'll bring the FAM. & some guns............
Title: Re: 8724 back from the dead Post by: rickh on February 20, 2011, 05:15:43 PM yep, sounds good... will have to see when.
Title: Re: 8724 back from the dead Post by: rickh on March 04, 2011, 03:41:35 PM This is the coin mech, harness, and mounting bracket I am mailing out today....
Who else needed parts? Next post will show what else is in this machine. Rick Title: Re: 8724 back from the dead Post by: rickh on March 04, 2011, 03:43:29 PM Here is the coin hopper and a shot of the stuff inside where the counters are....
Title: Re: 8724 back from the dead Post by: rickh on March 04, 2011, 03:44:15 PM Main board up top....
Title: Re: 8724 back from the dead Post by: knagl on March 04, 2011, 09:12:29 PM Hey Rick-
What's the number on that PAL chip (circled in green)? I have a friend who may be interested in the entire chipset, depending on the number on the PAL chip. Thanks in advance! (http://i55.tinypic.com/2i04w49.png) Title: Re: 8724 back from the dead Post by: rickh on March 04, 2011, 09:25:59 PM lemme check
Title: Re: 8724 back from the dead Post by: rickh on March 04, 2011, 09:29:14 PM 156-xxx
Title: Re: 8724 back from the dead Post by: knagl on March 04, 2011, 09:31:44 PM Aah, no good for him as he doesn't have the right clear chip for that software. Thanks for checking, though, Rick. K+ to you.
Title: Re: 8724 back from the dead Post by: rickh on March 04, 2011, 09:35:00 PM ya man... I am gonna pull usable parts out then kill the cabinet next time I shoot....
Title: Re: 8724 back from the dead Post by: rilaw on March 05, 2011, 07:02:59 PM Aah, no good for him as he doesn't have the right clear chip for that software. Thanks for checking, though, Rick. K+ to you. I just through my board on ebay, that chip is marked 155-XXXX on mine, don't know if that is what you were looking for... Title: Re: 8724 back from the dead Post by: knagl on March 06, 2011, 09:38:59 AM Very kind of you, rilaw. My friend has the clear chips for 153 and 010, so anything else is unfortunately useless to him.
|