New Life Games Tech Forums

Ffter you clear and set and you are at Key chip config what are the next steps to set machine for multi denom for 1 cent 2 cent 1 cent 5 cent do you go to accounting first and what detemins the money at compairitor and bill validator is it the 1 cent or can you make it 5 cent I am a little slow I need step by step         Thanks Paul

You have to set your accounting denomination at or below the lowest player denomination. If you want to have a 1 cent machine you can't have accounting denom set at .25. After that you can navigate to player denomination 1, 2, 3, 4 and so on and set those to the denom options you want, then set the paytables (returns) for each denom. Once you set those up you have to set a coin value, if using coins. I usually set mine to $100, you get $100 in credits for each coin inserted and each coin paid out of the hopper = $100.

when setting player denom i can set player 1 at 1 cent player 2 at 2 cent player 3 wants to start at 3 cents and i want it at 1 cent and player 4 will go to 5 cent i have tried to set this machine with no luck touch pad only acts on player 1

Do you have to ram clear every time if you mess up the settings by not getting multi denom. that you want ?

Thanks for a reply !!!!!!!!!!

yes you do or you get key chip access failure this is only if you save all info and try again

No Ram Clear is needed each time you change these settings.

Check out the old post on multi-denom

http://newlifegames.net/nlg/index.php?topic=3406.0 (http://newlifegames.net/nlg/index.php?topic=3406.0)

Thanks for the info got it going was having problems with using 1&3 and 2&4 on the touch pad, but all is well now THANKS!!!!!!!!!!

Thanks Again Danny

To recap Paul is trying to set a S 2000 for touch pad multi denom. The values he is wanting are  .01, .02,    With a whole lot of trial and error I've figured a way to do this.
                                                                                                                                      .01. .05

I used a machine with a SB****  , SG000363, & VS011GX1   Start out doing a clear with a 097 and use a Key 31 to get into key menu. With the base chip back in machine. start set up.

7.1.1.1 accounting    set at .01
7.1.1.2 coin denom.  set at .05   ( note you folks with coin handling the amount you set coin denom at is the amount of credits you will receive for each coin dropped into hopper. Example
                                                set coin denom at $100.00 and you will receive same credits as a $100.00 bill inserted in the BV)
7.1.1.3 Player denom. set player #1 at .01  player #2 at .02  leave player #3 disabled, player #4 .05 ( now we have to skip a step and then go back )
7.1.2    Game selection  Set players #1,#2, & #4 to your desired pay %
7.1.1.4  Touch panel    surf through the different options using the cash out and/or call buttons until you see 1/3 assign this to .01 press max bet and save, then go back into 7.1.1.4 surf through the options and find button #2 assign this button to .02 , max bet to save back into 7.1.1.4 and assign button #4 to .05.

Remember in 7.1.1.3 we left player #3 disabled, but with this setup it's not disabled anymore.
 I would think this is a hard way to do all this, but it works !!   ( Please note you have been in clear/key menu, don't forget to set machine type Upright/Slant Top, and turn your printer on in config II (unless you want to use the key chip again )

If I forgot anything, just remember I'm OLD, I have a excuse

 :259- Buzz for putting it all in one concise post.


Topic moved and stickied.

Stat :31-

Strat Where did you move topic and why was it moved

... to the right place. lolol  :30- :200-  :72- :72- :72-

Just scroll up and look. :96-