|
Title: S2000 reel tilt 2 Post by: zarobhr on July 28, 2011, 06:10:49 PM I changed my crappy non washable reel strips and now when reels cycle after power on or closing door reelo 2 only turns a little bit and goes to reel 2 tilt. i have tried another reel but same issue, what else can i check
Title: Re: S2000 reel tilt 2 Post by: Yoeddy1 on July 28, 2011, 06:18:22 PM Since you've determined that the reel isn't the problem, assuming that those same reels work in slot 1 and/or 3, I would try open and close the main door a couple of times to see if the reels will spin up and if you get to an insert coin status on the display. Power cycling the machine would be a good idea too. With the power off, reseating the MPU wouldn't hurt.
Jason Title: Re: S2000 reel tilt 2 Post by: Yoeddy1 on July 28, 2011, 06:20:06 PM Turn jackpot key? Can't hurt.
Jason Title: Re: S2000 reel tilt 2 Post by: zarobhr on July 28, 2011, 06:27:11 PM swapped reels with different machine , open and closed door several times, turn jackpot key with door opened and closed, and power cycled several times
still reel 2 tilt Title: Re: S2000 reel tilt 2 Post by: Yoeddy1 on July 28, 2011, 06:32:38 PM Interesting. Was the reel removed or installed while the power was on by chance? Do you have another MPU that could be tested? Might try reseating reel cable connections too.
Jason Title: Re: S2000 reel tilt 2 Post by: StatFreak on July 28, 2011, 06:46:33 PM After Jason's suggestion, try swapping the harness connections between reels one and two (with power OFF), and see if the tilt follows the reel or the harness.
Title: Re: S2000 reel tilt 2 Post by: zarobhr on July 28, 2011, 06:58:10 PM dam looks like my mpu board is the problem, i swapped it out with another and no more tilt, swapped it back and it tilted again
any idea what gets lost when i swap the boards? i noticed that my multidenom stayed the same what about meters, asset id, progressive setup etc anyone know Title: Re: S2000 reel tilt 2 Post by: Buzz on July 28, 2011, 07:35:19 PM What Game chips ( SG****** ) do you have on the bad board and on the good board ??
Title: Re: S2000 reel tilt 2 Post by: zarobhr on July 28, 2011, 07:46:47 PM both are 363
Title: Re: S2000 reel tilt 2 Post by: Buzz on July 28, 2011, 07:59:37 PM Well you shot my idea in the foot. What happens if you put the bad board in the good machine ?
Are you going to loose some settings by switching two boards between two machines, I'd say pretty good chance you will. Title: Re: S2000 reel tilt 2 Post by: zarobhr on July 28, 2011, 08:06:30 PM well i did the swap and didnt loose anything but the secure enhanced validation id for SAS.
all my progressive info, meters asset ID, multi denom, etc did not change the biggest thing i was worried about was the meters since i poll them with sas and record it, even auto poll it and record when the cash box is pulled for my drop. just to see if everyhting matches up. of course the only thing every in cash box when i pull it is about 100 redeemed tickets lol Title: Re: S2000 reel tilt 2 Post by: Buzz on July 28, 2011, 08:09:59 PM What I meant was, does the bad board work in the good machine ?? And the good board work in the bad machine ??
Title: Re: S2000 reel tilt 2 Post by: zarobhr on July 28, 2011, 08:12:52 PM aw gotcha the good board is working in the bad machine (which means the machine is good now.)i do not have another machine ready to try the bad board yet, but if i put it back in the same machine reel 2 still tilts, so its definately a bad board
Title: Re: S2000 reel tilt 2 Post by: Buzz on July 28, 2011, 08:17:40 PM aw gotcha the good board is working in the bad machine (which means the machine is good now.)i do not have another machine ready to try the bad board yet, but if i put it back in the same machine reel 2 still tilts, so its definately a bad board OK I see you installed a spare board. When you installed the spare, did you use the Base and Game chips from the bad board ?? Title: Re: S2000 reel tilt 2 Post by: zarobhr on July 28, 2011, 08:19:10 PM nope
the new board i put in had the same chips Title: Re: S2000 reel tilt 2 Post by: Buzz on July 28, 2011, 08:26:21 PM You can see where this is going, Do you have a bad board or bad eproms ??
Title: Re: S2000 reel tilt 2 Post by: zarobhr on July 28, 2011, 08:29:45 PM guess ill drag another machine out of storage i test it in there
Title: Re: S2000 reel tilt 2 Post by: CaptainHappy on July 29, 2011, 04:47:35 PM You can see where this is going, Do you have a bad board or bad eproms ?? guess ill drag another machine out of storage i test it in there I think that Buzz is trying to get you to swap the eproms from the bad board to the good board :79- to see if the problem follows the chips or not.... Gotta give him credit :259- as that is much easier than dragging anoth machine out at this point. :89- CH :95- Title: Re: S2000 reel tilt 2 Post by: staz on July 29, 2011, 05:49:16 PM i still find it strange that your mpu would go bad just by pulling the reels out.....i pull my reels out all the time on my s2k to clean them....as long as your machine is off when you pull them.......
|