Title: S2000 10-button deck problems Post by: stayouttadabunker on August 24, 2011, 12:25:14 AM :99- I have one of those S2000 9 or 10 button decks ( I didn't count them... :72-)
Has all the harness and I/O cards and other goodies.... :184- I think it was pulled off of a Cleopatra game? Anyways, I'm pretty sure it's designed for the 9-line multiple-bet-per-line games. Would I have to switch it all back out should I decide to throw in a more generic game kit such as a 3-coin 1-line DD Haywire Deluxe kit? In other words, does the more modern button button deck work with older kits? :129- Thanks for any help you guys!!! NLG rocks!!! :284- Title: Re: S2000 9 button deck - Backwards compatiable? Post by: Slotmaster on August 24, 2011, 12:20:27 PM They are not so you have to use the standard 5 button for the 3 reel 1 line games.
I think some buttons will work as the orginals it will not look right or light up correctly. So I have played 3 reel games with a dual row deck but it just was not the same as having the correct deck as everything was off. Title: Re: S2000 9 button deck - Backwards compatiable? Post by: stayouttadabunker on August 24, 2011, 01:19:52 PM I was thinking the same thing though I haven't seen it.
I suppose I could just move some connectors to the correct button tabs and get it to "look right". I have to try a button deck swap with my dual row and see what it looks like and how long it takes me to do a swap. Title: Re: S2000 9 button deck - Backwards compatiable? Post by: Slotmaster on August 24, 2011, 01:53:06 PM I tried it and it was not worth the time, qucker to change the panel and have it look and play right.
Title: Re: S2000 9 button deck - Backwards compatiable? Post by: stayouttadabunker on August 24, 2011, 02:44:45 PM Thanks SM!
I'll try a deck swap tonight to see how it goes. Now, all I need is a 9-line 180 bet-per-line game kit! :72- ohh...this hobby...sooooo expensive! lol Title: Re: S2000 9 button deck - Backwards compatiable? Post by: stayouttadabunker on September 14, 2011, 02:47:05 AM OK,
I have the 10-button deck in... took a couple of hours...lol I also installed the "802" I/O cards onto both sides of the door panel. I now have the error saying basically>>> "The 10-Button I/O Cards Are Missing" I noticed when installing the new harness coming from the door panel that there was a 6-pin (3 X 3) white Molex connector with mostly orange wires going into the back of it near the motherboard area. Where does it plug into? lol That might help get rid of the "Missing I/O Cards" error? :72- I think I gotta do a Clear and set the denoms to like a penny, 2 cents, 5 cents, $100? How do you guys set up the 5 Reel 9 Line 45 Credit Cleopatra's? Title: Re: S2000 9 button deck - Backwards compatiable? Post by: cowboygames on September 14, 2011, 10:44:51 AM Mine is set for .01, .02, .05 and .25. Changing the button deck is one of the rare cases where running a clear is a good idea and even better if you do it before you change the deck. Clear the machine, then change everything you want as far as hardware and software before you ever turn the machine on again. Then key it and set everything up in the menus before you try to put a single credit on the machine.
Title: Re: S2000 9 button deck - Backwards compatiable? Post by: stayouttadabunker on September 14, 2011, 11:37:23 AM Hmm...I was not able to change it from a quarter to anything else.
I think I should try a clear... I noticed that the back of these "802" I/O cards have amber LED lights on the boards. In the photograph I took below from directly above the two door panel cards, you can see the 2 amber LED lights as "on" on the belly side I/O card. However, there are no lights "on" the coin mech side of the door panel I/O card at all. :8- I'm suspecting that it may be a dead card? :103- This could be the reason why the machine is sending out the "Missing I/O card" error to the VFD display? Also, how does the display board up behind the reel glass ( Bet Per Lines Display) get hooked up? Am I missing a harness for that? If so, I may be able to make one as I have all kinds of harness parts ( Molexes, wires, pins,etc...) Title: Re: S2000 10-Button deck problems Post by: stayouttadabunker on September 14, 2011, 11:41:38 AM Here's a picture of the reel glass display for the 9 to 45 credit Bet Lines.
Is it Netplex driven? I'm wondering how it get's hooked up? Also a photo of same picture above of the door panel I/O cards without all my scribbling on it...lol >>> Title: Re: S2000 10-Button deck problems Post by: stayouttadabunker on September 14, 2011, 11:46:29 AM using a flash with same pic and another of the coin mech side of the door panel I/O card.
You can clearly see the amber LED lights "on" the belly side I/O card but none "On" the hopper side of the door back panel... :8- >>> Title: Re: S2000 10-Button deck problems Post by: stayouttadabunker on September 14, 2011, 11:47:46 AM Looking at the belly side I/O card next to the coin mech chute and the LED lights "on"
coming from the card with the belly door open... These pictures were taken with a high resolution setting so you can click on any photo and enlarge them if needed... I would like to try another 10-Button card. If anyone has one for sale, could you please let me know and I will Paypal ya! :99- :299- I think I better ask "dad" ( Blueridge Slots) if he's got any on hand... :89- Thanks! By the way, I'm wondering if it matters which "802" card goes into these two I/O card slots on the door panel? Aren't they not the same circuit boards? If so, then I could swap the front with the back one to see if the LED lights come "On" on the card that is not lighting up? >>> Title: Re: S2000 10-button deck problems Post by: blueridgeslots on September 14, 2011, 12:31:32 PM I can't believe none of your buds are stepping up here Mark, hell even the guy you got the "rare" 802 cards from has these pics I took for him, I can't understand why the sellers of stuff (like simms) $5 cheaper than us don't take the time to help after the sale, need to research that one, I guess cuz you don't make extra for support possibly, anyway here are some pics, your answers are yes you can swap the cards around, ans second you are missing a harness for the line display, it needs to be daisy chained into the button panel harness, pics are large for reason but if needed to be smaller feel free o change
Title: Re: S2000 10-button deck problems Post by: blueridgeslots on September 14, 2011, 12:34:09 PM pic
Title: Re: S2000 10-button deck problems Post by: stayouttadabunker on September 14, 2011, 01:52:37 PM lol Thanks for the excellent pictures BlueRidgeSlots! :131-
I just really got around to figuring out how these 10-Button set-ups work yet. :103- I need to see if you have one of those Bet Line display harnesses. If not, I will try to construct one. PM'd you my wants and needs to cure my slot addiction! :72- I will try the I/O swap this evening and see if the other one lights up at all. I noticed that there's an unscrewed double green button ground eyelet. I highlighted it with an arrow. Just wanted to help ya a little since you help so many here at NLG! >>> Title: Re: S2000 10-button deck problems Post by: zarobhr on September 14, 2011, 07:08:02 PM getting ready to power up my cleo i will take some pics for you on the cables for the display and let you know on the IO
sry was working more thanb usual today Title: Re: S2000 10-button deck problems Post by: stayouttadabunker on September 14, 2011, 10:54:09 PM That's okay Zarobhr,
I played 18 holes of golf...lol Okay, I got home and swapped the I/O cards from front to back and back to the front acceptor slide connectors. ( Is that what they're called? lol) The result after powering up is that now the "other" 802 I/O lights up in the belly side slide. So, now we know that both the I/O cards are functioning...they just won't function in the hopper side slide. A couple of things could be wrong and I'm suspecting a bad wire perhaps on the hopper side slide or a possible oxidized receptor hole pin-reciever causing the I/O to NOT power up? I don't know really but I'm going to pull it all back out and run a continuity tests on every single wire on that harness and search for a bad connection or internally busted pin connection. Lots of times wires bust inside the plastic wire cover and you cannot see the break. The only solution is to run continuity tests until you find the break. Secondly, I am NOT able to set the denominations for the 6-6-3 touch panel for more than a single touch panel denom - I am only able to set a single denom for a single touch panel spot. Could I be using the incorrect SB or SG chips? What are the recommended SB and SG chips for this 5R 9L 45 Credit game kit? Thanks for any help you guys can give me on this game! Title: Re: S2000 10-button deck problems Post by: cowboygames on September 15, 2011, 12:27:05 AM Bunker, you have to set payback percent for all denoms before you can set denom values and the accounting denom has to match or be lower than your lowest denom selection option. If I'm not mistaken there is also a place in the setup menu that identifies what button deck is installed. Have you run a full clear on the machine yet?
Title: Re: S2000 10-button deck problems Post by: stayouttadabunker on September 15, 2011, 12:43:06 AM I did do a Clear and set the machine's denom for a penny cowboy!
What keychip # should I use to get into those settings?? I might be using the wrong keychip cause it won't allow me to set more than one denom panel on the four touch screen panels. I don't see any options for any button deck configurations. okay, Breaking news update... lol I found a 14-pin molex harness in my junk box along with the little short black Molex adapter harness that I made one time for a reel touch panel. I plugged those together from the hopper-side I/O up to the Bet Line display board. Then I unplugged the 14-pin Molex I had in the belly-side I/O up to that same Bet Line Display board. Thanks to Zarobhr for noticing this! :244- :3- :293- :284- I called him up long distance while I was eating a Big Mac at McDonald's... :72- Apparently this Bet Line display board is critical in having the I/O working. The 1st thing I noticed when I powered up is all the 10-Button lights are on! Cool ! :133-:267- And the yellow amber LED lights on both of the I/O cards lit up too! :136- On the VFD display after booting up and the reels doing their maiden spin was showing that it was a penny game that I had set it to earlier this evening! :89- :91- :71- And the VFD was also showing that it was a 45 Credit game!!! WHeee!!! Now for the bad news.....I now have the dreaded "Coin--In Jam" error and everything freezes up if I hit the test button on the MPU.... :97- :72- :37- :8- :8- :8- What the heck is going on here? Am I still hooking this 10-Button deck & Bet Line Display harnesses wrong? :129- :128- Title: Re: S2000 10-button deck problems Post by: zarobhr on September 15, 2011, 12:46:57 AM need more pics showing your io cards top and botttom so i can see what is plugged into what
Title: Re: S2000 10-button deck problems Post by: stayouttadabunker on September 15, 2011, 12:56:34 AM need more pics showing your io cards top and botttom so i can see what is plugged into what I left my camera at work this afternoon Zarobhr...arghh! :279- 1: I have the door harness 14-pin Molex going up to the Bet Line board. 2: I have the black Bet Line header going down to the belly-side I/O. 3: I have the hopper-side I/O plugged into the other door harness 14-pin Molex. That's pretty much it. :103- I don't think the harness coming out of the black Bet Line is the correct pin configuration. :60- I just put that together from junk I had without looking at wiring schematics hoping it would work.... :72- I have to double check with some wiring schematics or some good photographs of that particular harness. If not pictures, then a hand drawn pin-out from the Bet Line board down to the belly-side I/O? Title: Re: S2000 10-button deck problems Post by: zarobhr on September 15, 2011, 01:03:43 AM you may try swapping the 14 pin from one io to the other and vise versa
Title: Re: S2000 10-button deck problems Post by: stayouttadabunker on September 15, 2011, 01:06:43 AM I just swapped the I/O connectors 1st.
Now I get a "Meter Not Working" error. There's no lights on the Bet Line board when I do this. So now I KNOW it's the makeshift harness I pulled out of my junk box. Title: Re: S2000 10-button deck problems Post by: cowboygames on September 15, 2011, 01:09:47 AM As far as the denoms go, did you set a payback percent for each of the denoms before attempting to assign the specific denom? Also, did you assign each button on the touchpad to a denom?
Title: Re: S2000 10-button deck problems Post by: stayouttadabunker on September 15, 2011, 01:10:56 AM I swapped the I/O 14-pin Molexes back and now get the "Coin-In Jam" error
and have no green LED light on the Bet Line board. I see the problem now. I/O cards are both good. Bet Line display board is good. I have to make a harness from the Bet Line board to the belly-side I/O card... for cowboy: No...I can't... I haven't been able to get into the settings with my Keychip31. Should I try a Keychip45 instead? Or would you suggest another clear? Then Keychip45? Title: Re: S2000 10-button deck problems Post by: cowboygames on September 15, 2011, 01:11:50 AM Sounds like you had your 14 pin plugs right. Do you have 663 display selected in the menus also?
Title: Re: S2000 10-button deck problems Post by: cowboygames on September 15, 2011, 01:14:03 AM Till you get the IO card thing worked out you may not be able to get into the menus. Key 31 should be fine. Key 45 is more for 1270 boards and reel touch games or newer
Title: Re: S2000 10-button deck problems Post by: cowboygames on September 15, 2011, 01:20:08 AM What version chip are you using in that machine bunker?
Title: Re: S2000 10-button deck problems Post by: stayouttadabunker on September 15, 2011, 01:23:13 AM Yes Cowboy,
I set it for a 6-6-3 VFD display and that's working fine...no problems there. Thanks for your help! :89- I'm pretty darn sure it's just a harness issue at the moment. BlueRidgeSlots pointed that out to me this morning but his photos ( while excellent pictures too!!!) didn't exactly show where it goes to. I must thank "Dad" for his help on this as he offered to send me a harness. I told him to hang onto to it as I will try to make my own with the junk I have laying around. I will make a brand new one in the morning. Seems like every LED light and button lights are working but the machine is confused by my garbage harness I picked out of my junk box...lol I am checking schematics as we speak. Version chip...uh...lemme check I'll be right back Title: Re: S2000 10-button deck problems Post by: stayouttadabunker on September 15, 2011, 01:26:03 AM okay,
I have>>> SB100104 SG GME's 1&2 363's VSO11GX1 SIMM card DSV00043 Keychip31 available... You guys have a great night and thanks so much for trying to help me out!! :3- :244- I gotta get to bed. :294- ...gotta actually try to make it to work on time in the morning! :208- Title: Re: S2000 10-button deck problems Post by: cowboygames on September 15, 2011, 01:36:50 AM Well, your version chip is good, might be best to hold off on the denom thing till it's the last problem.
Title: Re: S2000 10-button deck problems Post by: stayouttadabunker on September 15, 2011, 01:32:56 PM okay,
According to Blueridge's photo of the back of the BetLine board, the black Molex comes out of it and runs down to the belly-side I/O card. The only thing I can see in that photo is the numbers on the harness itself: 6004000 Can anyone email me or post up a hand-drawn pinout of the wires that goes from the black Molex out to the I/O card? I want to make a harness with the right pin locations. Much appreciated! :89- Title: Re: S2000 10-button deck problems Post by: zarobhr on September 15, 2011, 01:35:33 PM i can later tonight
Title: Re: S2000 10-button deck problems Post by: stayouttadabunker on September 15, 2011, 01:59:55 PM That would be great zarobhr! :244-
Thanks a lot buddy! :131- :3- I posted a couple of pictures below here to show people which pin is number #1 and so on. The 1st picture is the 14-pin white Molex for the belly-side door I/O. The 2nd photo is the black 12-pin Molex that comes out of the back of the BetLine board. Disregard the wires I already have in these pictures - I was only using them as examples... Click on any photo enlarge if needed!...>>> Title: Re: S2000 10-button deck problems Post by: zarobhr on September 15, 2011, 04:52:35 PM white to black
pin 1 to pin 1 pin 2 to pin 7 pin 3 to pin 2 pin 4 to pin 8 pin 5 to pin 3 pin 6 to pin 9 pin 7 to pin 4 pin 8 to pin 10 pin 9 to pin 5 pin 10 to pin 11 pin 11 to pin 6 pin 12 to pin 12 pin 13 nc pin 14 nc Title: Re: S2000 10-button deck problems Post by: stayouttadabunker on September 15, 2011, 11:35:25 PM Sir,
Are you my angel in heaven? :131- Thank you very, very much!!!! :293- :284- I will get to work constructing a harness in the morning!! :89- :71- Title: Re: S2000 10-button deck problems Post by: stayouttadabunker on September 18, 2011, 11:37:28 PM I want to thank zarobhr for the pinouts for this harness that goes between the Bet Line board down to the belly-side I/O card.
I double-checked the harness and my wiring is pinned out exactly as how he laid it out to me. :209- However, after connecting the harness - I am still getting the "Coin-In Jam" error .... :8- While the machine is powered up, two amber led lights are "ON" on the belly-side I/O while the hopper-side I/O card only has a single amber LED lit up. I am also getting a continuous green ( DS1) LED light on the back of the Bet Line board. Are you guys getting the same lights I am... lit up? :129- Title: Re: S2000 10-button deck problems Post by: stayouttadabunker on September 19, 2011, 12:08:26 PM :299- I suspected that there might be something wrong with the Line Bet display board that is located behind the reel glass.
What this board does is display to the player, how many bets each line is multiplied by. :71- It wasn't lighting up any numbers :103- I assumed it should it least be showing "zeros" for the Bet per line because I've never installed this game before...Hmm... So I removed it from the reel glass and pulled out the new harness I made for it. Voila! Under the microscope :209- you can clearly see a burned-out trace located near the C2 IC component. :8- :37- Look at the smoke that escaped at one time from under the silver colored (22 VFC 1R2) can! :98- Click on any photo to enlarge>>> Title: Re: S2000 10-button deck problems Post by: stayouttadabunker on September 19, 2011, 12:38:45 PM A well known vendor was watching this thread
and is sending me a new tested board! :wa :136- He's one of the best vendors I've ever dealt with and I cannot express how much I am grateful for all of his help!!! BlueridgeSlots! :293- :284- :285- Title: Re: S2000 10-button deck problems Post by: stayouttadabunker on September 20, 2011, 01:41:37 PM I was told that the Line Bet board may have been shorted and caused a surface mount (SMF) fuse to blow.
I'm not quite certain what is exactly burned out on the Line Bet circuit board but because of the smoke stains on the side of the SMT aluminum electrolytic capacitor (Panasonic 22 VFC 1R2) - Perhaps the cap blew out from underneath the base? Anyways, I'm trying to figure out what the "22" stands for on the alum cap printing. 22uf? :103- Would the "V" in front of the "FC" mean 35volts? Please excuse me for not understanding how they label these IC components... :182- Here's a link to a sheet from Mouser about these caps. I'm wondering which one I should get voltage-wise...>>> http://www.panasonic.com/industrial/components/pdf/pic_fc_series.pdf (http://www.panasonic.com/industrial/components/pdf/pic_fc_series.pdf) Also, the trace going to the little white block ( 1A 125v LF 460 ) at location F1 is slightly bloated and crystallized the green circuit board paint knocking it clear off the trace! I'm only guessing at this point that the location label (F1) means that a "fuse" IC component (numbers above) is soldered there? Continuing, I'm guessing this label "1A" means 1 amp the 125v is obvious but the "LF 460" is the "fuse" name? It's all black on the side where the trace from the cap enters it. I unsolder-ed both components and found lots a black char on these areas. ADD>> I found it! I was mistakenly seeing an "IE" when it was really "LF"... :25- Here's a link to the page on these SMF surface mount fuses made by...you guessed it... the "Littel Fuse" fuse company...! :97- >>> http://www.littelfuse.com/data/en/Data_Sheets/Littelfuse_Fuse_460_PicoSMF.pdf (http://www.littelfuse.com/data/en/Data_Sheets/Littelfuse_Fuse_460_PicoSMF.pdf) My immediate goal is to try and purchase these IC components, install them, and try to see if the board will function later on. :71- Title: Re: S2000 10-button deck problems Post by: zarobhr on September 21, 2011, 05:48:12 PM did you get this working yet
Title: Re: S2000 10-button deck problems Post by: stayouttadabunker on September 21, 2011, 10:39:07 PM Not yet, it's sitting and awaiting on UPS for a new Line Bet board.
Doesn't seem to work without it? I'm checking the mail and expecting the board to be in by Friday evening. Title: Re: S2000 10-button deck problems Post by: stayouttadabunker on September 23, 2011, 11:37:38 PM ***Breaking News Update***
I threw in the Line Bet board Blueridge sent me... The machine went through the motions of booting and searching Netplex stuff and then BAM! :279- Title: Re: S2000 10-button deck problems Post by: FORDSBS on September 23, 2011, 11:41:09 PM Same problem?
Title: Re: S2000 10-button deck problems Post by: zarobhr on September 23, 2011, 11:41:38 PM Hope thats a good Bamm
Title: Re: S2000 10-button deck problems Post by: stayouttadabunker on September 23, 2011, 11:42:15 PM IT WORKS!!!!
:152- :267- :199- :wa :92- Me slapping my head was just remembering I left the battery for my camera on the charger at work....lol Title: Re: S2000 10-button deck problems Post by: FORDSBS on September 23, 2011, 11:42:56 PM :wa :136- :105-
Title: Re: S2000 10-button deck problems Post by: zarobhr on September 23, 2011, 11:43:24 PM Whew. Congrats
Title: Re: S2000 10-button deck problems Post by: stayouttadabunker on September 24, 2011, 01:39:09 AM lol Thanks to you guys !!!
Kudos + for all! :285- I'm having a blast playing with all the different denomination possibilities! :79- :91- I was cleaning up my toolbox and putting my tools away. It's pretty late at night then I hear this lady's voice that scared the living shut out of me! It was the Cleopatra "attract" mode playing... I better turn the bloody volume down because I think the Cleo woke up every sleeping field mouse and animal out in the backyard! :96- Title: Re: S2000 10-button deck problems Post by: Ron (r273) on September 24, 2011, 10:22:13 AM One month and 47 posts later, I knew you could do it. :79- :79- :30-
Congrats on a job well done! Ron (r273) Title: Re: S2000 10-button deck problems Post by: PLUNGER BOY on September 24, 2011, 12:13:37 PM lol Thanks to you guys !!! The attract mode can be a very daunting feature. I'm building a new home and was working into the wee hours of the am. earlier i ran out of credits on the mummy . I was closing up the house to go home and all the lights were of but the slot machines as i was shutting the power of machines and walked by the mummy it went off There is nothing like a growling mummy at 3 am to raise the hair on your skin :97- :97- :97- :97-Kudos + for all! :285- I'm having a blast playing with all the different denomination possibilities! :79- :91- I was cleaning up my toolbox and putting my tools away. It's pretty late at night then I hear this lady's voice that scared the living shut out of me! It was the Cleopatra "attract" mode playing... I better turn the bloody volume down because I think the Cleo woke up every sleeping field mouse and animal out in the backyard! :96- Title: Re: S2000 10-button deck problems Post by: stayouttadabunker on September 24, 2011, 12:49:25 PM In the end, I see that there's two amber LEDs "On" on the belly-side I/O and a single LED lite "On" on the hopper-side I/O card.
The Line Bet board has a continuous green LED "On". All of my questions are now answered and I'm using a Line Bet harness I made myself with the help of you guys! Title: Re: S2000 10-button deck problems Post by: FORDSBS on September 24, 2011, 12:52:33 PM :3- :3- Now it's time to do some playing. She does have a sexy voice. ENJOY
Title: Re: S2000 10-button deck problems Post by: stayouttadabunker on September 24, 2011, 01:04:17 PM I can't! lol
I have go meet an NLG member at the casino... There goes my weekly pay! :25- Title: Re: S2000 10-button deck problems Post by: FORDSBS on September 24, 2011, 01:07:00 PM I can't! lol I have go meet an NLG member at the casino... There goes my weekly pay! :25- Tell him I said Hi. I want to hear from him how much money he made @ casino. Title: Re: S2000 10-button deck problems Post by: stayouttadabunker on September 25, 2011, 11:49:42 PM LOL This is how it went down!
I gave Reho $50 bucks to play a sit down slant poker machine for me while I played $50 at a $10 Min. Blackjack table. While the dealer shuffled, and went over to check on his progress. He was up and down like a see-saw after three shoes of cards. I was also up and down - never had a chance to raise my bet any higher than $15... :37- Finally, during the 4th shoe - I nailed 2 blackjacks in a row and 2 double-downs!!! :91- I cashed out my chips and walked over back to Reho holding $100 in chips! He was way down to like around 25 credits then hit 4-of-a-kind with something and got the credits up to around 200-something!!! I told him to "CASH OUT!!!!! :72- We split $130 from the poker machine. So all in all, I was up $65 bucks and because I told him to keep half of $130 he made on the poker machine- he won $65 as well ! And he needed no starting capital too! Am I too generous?!?! :208- okay, I want to change my touch panel denoms on my Cleopatra 5 reeler. I can only get one square to program at the moment... I totally understand the fact that I need to perform a Clear in order to make denom changes but I need to know in what order do I make denom changes? I would like the 4 touch panel squares to be: .01 cent .02 cents .05 cents .25 cents Step 1: Perform a Clear Step 2: ? Title: Re: S2000 10-button deck problems Post by: cowboygames on September 26, 2011, 12:37:08 AM Then set accounting denom to .01, set payback percents, set player denoms and finally, set touchpad assignments
Title: Re: S2000 10-button deck problems Post by: stayouttadabunker on September 26, 2011, 02:44:10 AM Thanks cowboy! :3-
I'll try it in that order tomorrow evening after supper! :89- Title: Re: S2000 10-button deck problems Post by: zarobhr on September 26, 2011, 05:27:59 AM did you get a touchpad, if so do you have an extra,
Title: Re: S2000 10-button deck problems Post by: FORDSBS on September 26, 2011, 09:31:32 AM LOL This is how it went down!
I gave Reho $50 bucks to play a sit down slant poker machine for me while I played $50 at a $10 Min. Blackjack table. While the dealer shuffled, and went over to check on his progress. He was up and down like a see-saw after three shoes of cards. I was also up and down - never had a chance to raise my bet any higher than $15... hissy fit Finally, during the 4th shoe - I nailed 2 blackjacks in a row and 2 double-downs!!! yummy I cashed out my chips and walked over back to Reho holding $100 in chips! He was way down to like around 25 credits then hit 4-of-a-kind with something and got the credits up to around 200-something!!! I told him to "CASH OUT!!!!! rotflmao We split $130 from the poker machine. So all in all, I was up $65 bucks and because I told him to keep half of $130 he made on the poker machine- he won $65 as well ! And he needed no starting capital too! Am I too generous?!?! Cry Laughing Way to go. I'm happy for you guys having a good weekend. Title: Re: S2000 10-button deck problems Post by: stayouttadabunker on September 26, 2011, 11:36:59 AM did you get a touchpad, if so do you have an extra, zarobhr, I 've had this touchpad for about a year and did some posts on how to make the tiny little harness for it along with the links to the places where to get the parts for it. If I had another board, I'd be glad to sell you one of them as I only have a single personal machine. The multi-denomination touchpads are NOT made by IGT but rather, some other company and they're called "TouchCells" really. I think they're made by 3M but it's been a while since I dig some digging around for them. Here's the link to the thread we did on them about a year and a half ago...>>> http://newlifegames.net/nlg/index.php?topic=6854.0 (http://newlifegames.net/nlg/index.php?topic=6854.0) Then set accounting denom to .01, set payback percents, set player denoms and finally, set touchpad assignments I did get the TouchCells programmed the way I wanted but I know one thing - it wasn't in the oder you told me... :72- I screwed around with the options & settings and finally got it to program after putting in the Keychip31 again. LOL This is how it went down!.... Way to go. I'm happy for you guys having a good weekend. I actually only saw Reho and his buddy for a few hours 'cause I had to take off and go watch a youth football tournament. I'm not sure where those guys went afterwards! lol I hope they had fun because it was a gorgeous weekend to be outside! Changing-of-colors happening up in the Northeast here right now! Title: Re: S2000 10-button deck problems Post by: stayouttadabunker on October 10, 2011, 02:38:09 PM Okay, Just an update on my old Line Bet display board.
I soldered in a new Littel Fuse 1A fuse and a new 22uf cap. I swapped my displays and the old one now works great too!!! Whoo woo! :136- Now I have a working spare Line Bet display panel...maybe I oughta get another machine huh? :96- Sorry for the crappy cellphone pic...my better camera was elsewhere... At least you can see it's all lit up nicely with me betting 5 credits per line! :91->>> Title: Re: S2000 10-button deck problems Post by: zarobhr on October 10, 2011, 02:56:51 PM awesome that you got it fixed, years ago i used to fix stuff all the time now dont even have a solderong iron
Title: Re: S2000 10-button deck problems Post by: stayouttadabunker on October 10, 2011, 09:51:53 PM The tricky part about soldering these IC components is that
they usually fold the IC legs underneath the body. There's just a smidgen of tab on the edges where I can get some solder to weld. If the flux is placed just right, the solder runs underneath just right to the tabs and connecting traces with the heat drawing the solder nicely. It really is a lot simpler and easier done than said... :5- |