|
Title: Bally 6000 error 23 after ram clear Post by: slotsx2 on August 26, 2011, 06:54:19 PM I did a complete ram clear and now I keep getting error 23, coin not sensed. I don't have a hopper or a coin comparator, just a bill validator which lights up, powers up, but when the machine starts up and I get error 23, the bill acceptor doesnt light up at all. I've Been screwing with this for 3 days! Anyone with any suggestions as to what I am missing and/or doing wrong?
The clear chips are the flip dip switch off & leave em in type. Title: Re: Bally 6000 error 23 after ram clear Post by: a69mopar on August 26, 2011, 08:54:22 PM what position are the dip switches in on DS2? Is dip 8 on or off? The dip switch could cause this.
Do you have optics in the machine? Thanks, 'Wayne Title: Re: Bally 6000 error 23 after ram clear Post by: slotsx2 on August 26, 2011, 09:00:17 PM I checked all the dipswitch settings. All are ok. No coin optics at all. This just started after the ram clear. Checked all the settings a dozen times. I'm at a loss...
I tried dip switch on and off. Title: Re: Bally 6000 error 23 after ram clear Post by: a69mopar on August 26, 2011, 09:21:14 PM try swapping out the dip switch package. They just lift out like a chip. If you don't have others, then swap with ds1. I have known these to go bad before.
The other thing would be to check for a bent pin on the connectors at the rear of the board. Thanks, Wayne Title: Re: Bally 6000 error 23 after ram clear Post by: slotsx2 on August 26, 2011, 09:25:20 PM I neglected to mention, everything was working fine. All that happened was I did a clear to put a new game on it?
That was one of the things I did check for, bent pins on the board. Title: Re: Bally 6000 error 23 after ram clear Post by: paul on August 27, 2011, 12:55:17 AM are you flipping dips 8 on dsp 1 when doing a ram clear
Title: Re: Bally 6000 error 23 after ram clear Post by: slotsx2 on August 27, 2011, 01:46:15 AM yes
on to do the clear, off when done Title: Re: Bally 6000 error 23 after ram clear Post by: paul on August 27, 2011, 11:18:23 AM try 7 and 8 on
Title: Re: Bally 6000 error 23 after ram clear Post by: slotsx2 on August 27, 2011, 11:34:18 AM None of the dip switch settings have been changed from what they were prior to doing the ram clear. DS1 All on except 3 and 8.
Title: Re: Bally 6000 error 23 after ram clear Post by: b5srt on August 27, 2011, 11:42:12 AM Have you used those clear chips before with no issues ?
Title: Re: Bally 6000 error 23 after ram clear Post by: b5srt on August 27, 2011, 11:55:33 AM are you sure option 81 is set to 0000 "No coin acceptor"
Title: Re: Bally 6000 error 23 after ram clear Post by: b5srt on August 27, 2011, 12:18:49 PM Another thing to try is do a complete clear, program all your settings ( 81= 0000, 61 =0002), if you still get an error, hold the reset buttion for 2 seconds and close the door. If after that if you still have an error, just do a partial clear, DO NOT hold down the TEST or PSEUDO buttons, this will retain the previous settings and should clear any errors. Good luck
Title: Re: Bally 6000 error 23 after ram clear Post by: slotsx2 on August 27, 2011, 08:08:09 PM Got rid of error 23 now have eror 31
hopper coin out jam first time with these leave in clear chips Title: Re: Bally 6000 error 23 after ram clear Post by: slotsx2 on August 27, 2011, 08:27:07 PM Are you S...ting ME? All I had to do was push reset and shut the door, LMAO!
I HATE BALLYS............ LOL Thanks b5srt!!! |