Title: EPROM DATA... HELP!!!!!!! Post by: Rep on January 06, 2009, 06:35:32 PM Ok, one for you pros! My PE+ has been giving me this intermittently for a while. Press the self test button good to go. Today I wanted to play a little as I had to wait to pick someone up and I can press the self test til I'm blue in the face and can't get past this screen. Is it a bad data chip? Bad processor board? I have NO idea, and OF COURSE the spare board I do have has a dead battery so I can't do anything with that either. If it is a board problem is it something simple, I'm GOOD with electronics and pretty handy with a soldering iron should that help any with this issue... Any help would be GREATLY appreciated. Thanks guys :)
Title: Re: EPROM DATA... HELP!!!!!!! Post by: Brianzz on January 06, 2009, 08:57:12 PM I thought on PE+ to reset the eprom error you turned the jackpot reset key
Title: Re: EPROM DATA... HELP!!!!!!! Post by: Rep on January 06, 2009, 09:30:24 PM On mine all I had to do was push the test switch as this happened intermittently over the past few months (though I hadn't played much). I did try the jackpot reset as well, just brought up the game statistics :(
Title: Re: EPROM DATA... HELP!!!!!!! Post by: Rep on January 09, 2009, 04:58:11 PM Quick update, tried 2 other game sets. One superboard set and one older solo set. No dice, same deal. Cant clear the "EPROM DATA" error. I'm thinking either the superboard or motherboard? Any other suggestions? Also if I do need one or the other if any of the vendors have them please post. Thanks again!
Title: Re: EPROM DATA... HELP!!!!!!! Post by: jay on January 09, 2009, 06:26:44 PM Check the e16/e17 jumper.
E16/E17 must be on E16 for standalone games. Title: Re: EPROM DATA... HELP!!!!!!! Post by: Rep on January 09, 2009, 11:12:22 PM Yep, moved the jumper when I put the solo set in. Of course I did forget first and everything was whiteish and blurry. Moved it where it belonged and still got the same unclearable "EPROM DATA" error :(
Title: Re: EPROM DATA... HELP!!!!!!! Post by: Stolistic on January 10, 2009, 01:41:41 PM It is possible the EPROM on the backplane has gone defective. Do you get both a "Door Open" and "EPROM DATA" message on the screen? The self-test button will not activate with the door closed (i.e. bad door sensor).
Worse case you can pull the CMOS RAM to clear its contents and let the PROGRAM chip reload defaults. If you get past the CMOS DATA error your door is working, if not you probably have a sensor issue. If you get past the CMOS DATA error and still can't get past EPROM DATA, I would suspect the EPROM on the backplane. Title: Re: EPROM DATA... HELP!!!!!!! Post by: Rep on January 10, 2009, 01:56:43 PM That must be what it is then. I did pull the RAM to try that thinking maybe that was corrupted. No good, I can get past the CMOS DATA with no problem the EPROM DATA I just can't get past and I get no door open msg, the door optics are OK. So the EPROM is on the motherboard itself? I guess it'd be easiest to just replace it, a few screws and move the wires. If any vendors on here have one for a PE+ upright please let me know. Is the old one repairable? Is it soldered on or just in a socket? Either way I could probably do it (if it's doable) and hopefully have a spare. Thanks for the info Stol! Much apprecaited! At least I know where to look now :) K+ to you kind sir! :)
Title: Re: EPROM DATA... HELP!!!!!!! Post by: Buzz on January 10, 2009, 02:41:56 PM Try turn power off then power on hold self test until you hear beep close door if open door disappears on screen turn jackpot key one time
Title: Re: EPROM DATA... HELP!!!!!!! Post by: 2Nutz on January 11, 2009, 04:13:26 AM That must be what it is then. I did pull the RAM to try that thinking maybe that was corrupted. No good, I can get past the CMOS DATA with no problem the EPROM DATA I just can't get past and I get no door open msg, the door optics are OK. So the EPROM is on the motherboard itself? I guess it'd be easiest to just replace it, a few screws and move the wires. If any vendors on here have one for a PE+ upright please let me know. Is the old one repairable? Is it soldered on or just in a socket? Either way I could probably do it (if it's doable) and hopefully have a spare. Thanks for the info Stol! Much apprecaited! At least I know where to look now :) K+ to you kind sir! :) Pretty easy to unsolder the old chip, solder in a socket and then add the eprom chip. As I recall from a couple years back the only technical part was finding the replacement chip. Might still have an extra chip in one of my stands if you run into problems locating one.Fill out your location in your profile, you might be around the corner from another member with extra parts just stacked in the garage :103- Title: Re: EPROM DATA... HELP!!!!!!! Post by: Rep on January 11, 2009, 02:09:12 PM I would indeed like to repair it. I'll probably buy another board then repair the old one. Never a bad thing to have a spare. Spare parts are always good ;) I never filled out my location as the state I'm in thinks it's naughty to have a PE+ (or many other types of machines). Thanks for the info and help :)
Title: Re: EPROM DATA... HELP!!!!!!! Post by: StatFreak on January 11, 2009, 05:13:01 PM I would indeed like to repair it. I'll probably buy another board then repair the old one. Never a bad thing to have a spare. Spare parts are always good ;) I never filled out my location as the state I'm in thinks it's naughty to have a PE+ (or many other types of machines). Thanks for the info and help :) Join us at Area 51 in Nevada. :88- (Just look for my location.) Title: Re: EPROM DATA... HELP!!!!!!! Post by: Rep on January 13, 2009, 03:19:31 AM Hmm, not quite the right state but I suppose for NLG I can relocate. I'll gladly join ya in Area 51 :71-
Title: Re: EPROM DATA... HELP!!!!!!! Post by: StatFreak on January 13, 2009, 07:10:38 AM Hmm, not quite the right state but I suppose for NLG I can relocate. I'll gladly join ya in Area 51 :71- When we get enough members together we'll throw a huge party and take a joy ride on that ship they've had stashed out there for 50 years. I've heard that those spaceships fly like crap if you don't take them out of the garage for a spin at least twice a century! :5- :30- :127- :72- :72- :72- Title: Re: EPROM DATA... HELP!!!!!!! Post by: Neonkiss on January 13, 2009, 11:00:23 AM I never filled out my location as the state I'm in thinks it's naughty to have a PE+ (or many other types of machines). Thanks for the info and help :) Join us at Area 51 in Nevada. :88- (Just look for my location.) According to my profile, I'm homeless and I live in a park.. But I will work for food. Title: Re: EPROM DATA... HELP!!!!!!! Post by: Rep on January 13, 2009, 03:44:04 PM Gettin close to takin that ship for a spin, there's a few of us out there in Area 51 :D Come join us in Area 51 Neon, forget that park, we'll take ya in :D
Title: Re: EPROM DATA... HELP!!!!!!! Post by: jay on January 13, 2009, 04:25:44 PM Call me when you get to a critical mass then you can swing by and beam me up.
Icidently since you are more enlightend than I about this stuff, I have always wondered the following: Why does the new enterprise have a transporter room when they are able to beem people from the ground directly to the bridge or other places on the ship ? |