|
Title: Vision Game Change Problem Post by: jdkmunch on January 07, 2012, 08:01:06 PM I'm trying to change my DD Mine game into a pinball game.
I put in the pinball chips, and the drive for the top box. I first do a clear 97 and get the two lights on the mpu then I to a key 17 and get two lights on the mpu with the game sb in I get a ram error, then an eeprom error - press the little magic button for 3 seconds but then get this error which I can't get rid of. :37- Title: Re: Vision Game Change Problem Post by: jdkmunch on January 07, 2012, 08:02:47 PM I have also tried a 224 clear chip - however this boots the mpu but stops waiting for netplex. The top box displays initializing please wait.
Title: Re: Vision Game Change Problem Post by: idesign on January 07, 2012, 08:16:33 PM What RFA is in the machine? Also, use a key 31 with SG380, not 17.
Title: Re: Vision Game Change Problem Post by: jdkmunch on January 07, 2012, 09:02:15 PM how do I tell the RFA?
its definitely a game version problem I put back DD mine a d it worked like a charm Title: Re: Vision Game Change Problem Post by: idesign on January 07, 2012, 10:44:00 PM Open the back of the LCD and to the left of the memory stick you will see a set of jumper pins. I think it's labeled JP1.....put a jumper on it. Now boot the machine up and the LCD will display what it is doing when the machine boots. It should tell you what RFA is in the firmware. Also, how much memory in in that LCD? It will tell you that too when you boot. Make sure no cards in the side of the LCD, the card should be in the top.
Some photos of what you are getting may help figure out what the problem is. Title: Re: Vision Game Change Problem Post by: jdkmunch on January 07, 2012, 10:44:52 PM What RFA is in the machine? Also, use a key 31 with SG380, not 17. RFA 1025 Title: Re: Vision Game Change Problem Post by: Bettor Slots on January 08, 2012, 02:31:45 AM What Gm1 and 2 chips are you using? Like Idesign says you need to be using 380's with that title and you should also be using a VSo11GX1 version chip.
Title: Re: Vision Game Change Problem Post by: jdkmunch on January 08, 2012, 03:34:15 AM Yes - the game chips are 380 with vsof11gx1
Title: Re: Vision Game Change Problem Post by: Bettor Slots on January 08, 2012, 04:07:46 AM I would start questioning the ATA on the flash card and the SB chip then.
Title: Re: Vision Game Change Problem Post by: jdkmunch on January 08, 2012, 04:13:58 AM Yeah from what I've learned pinball requires
ata10065 (this I can't Check cause it's on the card) With game 380 The 380 requires clear 224 This is where I'm getting stuck - the clear 224 hangs waiting for the top box and the top box hangs with initializing, please wait... Title: Re: Vision Game Change Problem Post by: jdkmunch on January 08, 2012, 11:11:00 AM Top box has 31744k ram
Title: Re: Vision Game Change Problem Post by: cowboygames on January 08, 2012, 12:49:50 PM With the 224 you never get both lights on the MPU? Which MPU are you using? 502, 504 or 1270 enhanced?
Title: Re: Vision Game Change Problem Post by: jdkmunch on January 08, 2012, 03:05:22 PM I would start questioning the ATA on the flash card and the SB chip then. Success! - It was a corrupt SB Chip - I verified that the checksum was wrong - replaced it with a new one and it's up and running! I think the mpu has sound issues though - hear that sound pulsing during each spin - a similar sound problem that I was having with DD Mine. http://www.youtube.com/watch?v=snP8Co-Gxmk (http://www.youtube.com/watch?v=snP8Co-Gxmk) Title: Re: Vision Game Change Problem Post by: jdkmunch on January 08, 2012, 03:07:24 PM Thank you everyone for all your help - I think this is a fun game -
Title: Re: Vision Game Change Problem Post by: Bettor Slots on January 08, 2012, 03:45:15 PM Nice socks...are those Joe Boxer's ? :96-
Title: Re: Vision Game Change Problem Post by: jdkmunch on January 08, 2012, 03:47:27 PM How did you know ?
Title: Re: Vision Game Change Problem Post by: Bettor Slots on January 08, 2012, 04:19:24 PM How did you know ? LOL...well I know quality when I see it. :97- Title: Re: Vision Game Change Problem Post by: stayouttadabunker on January 08, 2012, 08:32:15 PM I have a question I could probably solve on my own by going through my computer
but I just changed my 10-button deck back to a regular deck. My s2000 hasn't had a regular deck in over a year! - I've forgotten! Where dos that long black harness from the button deck go to? lol Thanks! It has the black plastic corrugated cover over the wires. with a 12-pin Molex and a 2-pin (red & green wires) Molex. ADD>>> no...I remember now. It goes up around the top of the door over to the reel glass display. |