|
Title: help with zt1204 belt issues Post by: scratchee35 on February 24, 2013, 02:49:01 AM Good evening!
i just saw this on ebay...140921177271...the seller says they came out of a s+...the model number is the same as what is in one of my machines already but its in a s2000...anyone know if this will work? thanks!!! i have a zt1204 bill validator that is giving me fits... it was accepting bills sparatically, now its not accepting any...i while i was cleaning the head, i noticed that one of the wider black belts is very worn, part of it is wider than the other...the belt doesnt appear to be tracking right, as it looked like it wanted to roll *flip over* at the thinnest width of the belt when i put the 1204 in the machine, i see try to initialize, and the belt that is basically two different widths, doesnt travel like the good belt...wow..i hope all that crap makes sense i swapped validators between 2 machines,..the known working zt1202 works in both machines, and the 1204 does not work in the other machine either...it takes the bill in most of the way, then spits it back out...all bills, even the ones that it took before it stopped working altogether i looked on ebay, but cannot find this model, which is what i would like to have, but no luck...the chip on the bottom has zt12p 024 v2.23, can someone give me some ideas on what else might be wrong with this or have a place where i might beable to buy one....cheap!??? any help is very appreciated thanks!!! Scratchee35 Steve Title: Re: help with zt1204 belt issues Post by: monitorman on July 27, 2013, 05:30:06 AM The ZT1202 is IGT and should have a red cable on the side. what color is your 1204? and do both BV's have 024 firmware?
Title: Re: help with zt1204 belt issues Post by: scratchee35 on July 27, 2013, 05:16:20 PM my 1204 was replaced with a different one, 1202 i think...that machine is not here anymore
are you talking about the red cover that the wires run thru on the side? yea mine are red, on both the 1202 and 1204 i have 2 of the 1202's but the software chip says...mars zt gt s+&p+ v1.30(128f)...those numbers are very small and hard to read...now that ive typed it, am wondering if they are for the s-plus and p-plus machines i do not know if any of these 3 work as i have no way to test Steve Title: Re: help with zt1204 belt issues Post by: monitorman on July 27, 2013, 10:11:23 PM Yes that is what they are for S+ and pe+ games. A change of firmware can make them S2000 & game king.
Bill Title: Re: help with zt1204 belt issues Post by: scratchee35 on July 27, 2013, 11:24:30 PM wow..thats great to know...i dont have any s plus machines that take mars, and only a few that ive had pass thru had them thankfully...ill have to find the software and get them set up for the next time i get more machines...the one had major belt problems, so i took one apart to fix the other and now i have one without belts lol
Steve Title: Re: help with zt1204 belt issues Post by: monitorman on July 28, 2013, 12:32:12 AM if you need parts I have them. Can Belts, O rings pinch rollers "little plastic balls", Black and Gray transport belts and the light block. And EE-proms
Title: Re: help with zt1204 belt issues Post by: scratchee35 on July 28, 2013, 12:34:25 AM great to know...thanks for the info...know where i can get the software?
thanks!! Steve Title: Re: help with zt1204 belt issues Post by: monitorman on July 28, 2013, 01:14:56 AM I have the 1meg EE-Proms
|