|
Title: Install a bill validator in my S2000 Post by: Nurbo on April 21, 2013, 06:01:04 PM Hello,
I want to install a bill validator in my S2000. I think I need ID024 and preferably 2x WBA because it must read the Euros. I think the wiring in the machine at the location of BV is strange, 2 red and black cables cut. (http://www.subaudio.org/flipjuke/MAS/BV_wiring.jpg) (http://www.subaudio.org/flipjuke/MAS/BV_wiring.jpg) What do you think about this wiring ? Title: Re: Install a bill validator in my S2000 Post by: brianfink on April 25, 2013, 10:24:07 AM It looks like you are missing the plug for the power (the red and black wires that are cut and wrapped) but it could be spliced. I may be wrong but I always thought you needed a UBA to take Euros.
Title: Re: Install a bill validator in my S2000 Post by: Nurbo on April 26, 2013, 04:21:35 PM As a matter of fact, according to the seller, the bill validator that I need is WBA or UBA 23 - 24, but it mind be also a MEI.
Except the plug for the power, the wiring seems to be alright ? Thanks ! Title: Re: Install a bill validator in my S2000 Post by: brianfink on April 27, 2013, 10:14:56 AM As far as I can tell from the picture it seems alright the 5 green wires with stripes are for communication the yellow and black are for the bezel light and red and black are for power. Just make shure when you order it that you get the full unit with stacker and caseing with IGT wireing harness.
Title: Re: Install a bill validator in my S2000 Post by: Nurbo on April 29, 2013, 04:13:03 PM ok, thanks for your information, I'm waiting for news from the seller.
Title: Re: Install a bill validator in my S2000 Post by: Nurbo on May 23, 2013, 05:06:42 PM Hello !
At last, I got my bill validator and its Bezel. (http://www.subaudio.org/flipjuke/MAS/P1140154_TH.jpg) (http://www.subaudio.org/flipjuke/MAS/P1140154.JPG) It is an ARDAC 5. It is an old model but it was not expensive and it works well. I easilly succeded in making the installation, the S2000 helps well in this case. (http://www.subaudio.org/flipjuke/MAS/P1140175_TH.jpg) (http://www.subaudio.org/flipjuke/MAS/P1140175.JPG) However, there is a litlle problem…The bezell does not light. I know that it is not really useful, but… Find below the harness that plugs on the bezel. There are 4 wires, from left to right: - Red - Red / Blue - Black / Yellow - Yellow / Black If i am looking at the wires’ way, the 2 red ones (from left to right) are going to a card at the back of the CPU tray. The two other ones, black and yellow, are going to the back of the BV. (http://www.subaudio.org/flipjuke/MAS/P1140179_TH.jpg) (http://www.subaudio.org/flipjuke/MAS/P1140179.JPG) The two black and yellow wires that are coming from the door’s bezel are arriving at the back of the BV. Find below : the plug that is situated at the bottom of the pics. (http://www.subaudio.org/flipjuke/MAS/P1140177_TH.jpg) (http://www.subaudio.org/flipjuke/MAS/P1140177.JPG) Below, the data sheet of the ARDAC 5 model and I can not see where the black and yellow wires can be pluged in. (http://www.subaudio.org/flipjuke/MAS/ardac-connector.jpg) Finally, on the bezel’s card , can you tell me where is the power ? (http://www.subaudio.org/flipjuke/MAS/P1140184_TH.jpg) (http://www.subaudio.org/flipjuke/MAS/P1140184.JPG) You also find the full datasheet here : http://www.money-controls.de/manuals/wacs/44x500R4_ARDAC5_spec_adj_manual1.pdf (http://www.money-controls.de/manuals/wacs/44x500R4_ARDAC5_spec_adj_manual1.pdf) Thanks a lot ! |