|
Title: How to test Door Optics? Post by: John0813 on December 29, 2013, 06:04:52 PM I have an S2000 that I cannot Clear. I get stuck after the display reads: "Please close the main door". It will not allow me to go to the next step. I have changed the optics. I have read about a dozen posts about this issue. Is there a simple way that I can test my optics to make sure they are working correctly? Thanks in advance. Title: Re: How to test Door Optics? Post by: harp on December 29, 2013, 06:24:33 PM I assume that when you close the Main Door the display still shows "Close Main Door"
Have you checked the Belly Glass Switch? Title: Re: How to test Door Optics? Post by: John0813 on December 29, 2013, 06:27:21 PM Yes...the switch has been disconnected....I am waiting on a new MPU....I just thought if I could test the optics...I would know if they were working or not. Title: Re: How to test Door Optics? Post by: harp on December 29, 2013, 06:36:01 PM You can check in the I/O Test Menu
4.1.3 Processor Input Test Allows tests on circuits that provide input to the processor, such as machine doors and reel optics In this section it will bring up the Door Optics, when you close the Door you will see the change from O to 1 etc Title: Re: How to test Door Optics? Post by: erbs on December 29, 2013, 06:37:18 PM It could very well be the MPU. Had the same thing happen awhile back.
Title: Re: How to test Door Optics? Post by: John0813 on December 29, 2013, 06:44:03 PM How do I get to the menu?...If I cannot get past the message about the door?? Title: Re: How to test Door Optics? Post by: harp on December 29, 2013, 06:54:37 PM My bad, senior moment not thinking
Title: Re: How to test Door Optics? Post by: CVslots on December 30, 2013, 04:01:22 AM How do I get to the menu?...If I cannot get past the message about the door?? Press the test button on the MPU....Cash Out (equivalent to Page Down) to menu 4 as described by Harp...Cabinet I/O test. Don't get me wrong, I'd gladly sell you a replacement MPU! But I want you to confirm yours is actually bad before buying a replacement! :89- Title: Re: How to test Door Optics? Post by: John0813 on December 30, 2013, 10:28:31 AM Pressing the button does nothing.......no menu.....also.....FYI...to CV Slots....I ordered 2 MPUs from you last week.....Ha Ha Ha Title: Re: How to test Door Optics? Post by: CVslots on December 30, 2013, 03:13:57 PM And you should receive those today! Shipped Friday via Priority Mail. :89- Oh, and both boards have fresh batteries on them as well.
It could very well be the MPU. Had the same thing happen awhile back. :331- :331- Title: Re: How to test Door Optics? Post by: therockinelvis on December 30, 2013, 11:04:26 PM Sounds like the green Battery leaked and messed up your traces. I hate those batteries and remove as soon as I get a machine. The MPU should do the trick. Good Luck. Be careful changing your chips. Pay attention to the notches and extremely careful not to bend any legs on the chips.
Title: Re: How to test Door Optics? - Problem Solved Post by: John0813 on February 09, 2014, 02:15:53 PM Got the new boards....installed them into the machines.....everything worked fine.....Thanks for all your help and ideas. Title: Re: How to test Door Optics? Post by: erbs on February 09, 2014, 02:22:17 PM Glad to hear you got it working
Title: Re: How to test Door Optics? Post by: stayouttadabunker on February 10, 2014, 01:50:26 PM Got the new boards....installed them into the machines.....everything worked fine.....Thanks for all your help and ideas. Yay! Good job CV Slots! :3- |