New Life Games Tech Forums

Hi All,
I'm still having a couple of issues with this game. When I turn on the machine, the win meter displays "6". It will stay this way for about 3 minutes or so then the reel solinoids will click, click, click for about 30 seconds then everything is normal and the machine plays fine until the next time I turn it on. This only happens when the machine is cold. Once warmed up, and turned off, it will start right up when turned back on. I have checked everything I can think of. Nothing I do will fix this. I swapped the power supply and I/O boards with working ones from another machine and the result is the same. I have not swapped MPU boards yet. I don't want to take a chance at screwing up a good working MPU.
Does anyone have a suggestion as far as what to check or replace to fix this?

Thanks, Jerry

Finally figured out the code 6. It was a bad main board. Exactly what, I don't know. I really didn't want to take a chance of messing up a good board, but I tried evey thing i could think of and nothing worked to fix the problem. Finally, I broke down and swapped the board, ram card and eproms with a good one from another machine and now it works. Of course the other machine now doesn't work.
Before I buy a new board, does anyone know what components on the main board I should check which would give a code 6?

Still have the issue with the progressive. I have tried a hundred times to get the game in to progressive programming mode, and it just won't do it. I can't imagine I'm doing it wrong. I remove the top glass, press the two buttons and go to test 8. When the progressive arrow lights light up, I release the two buttons and....nothing. I tried it with the door lock open and closed. The display just shows 82000. It never shows 82128 or anything else that it is supposed to. The progressive meters advance at a 10% rate and when I check the book keeping meters, code 30 and 31 come up and show the correct current meter values. I checked the buttons at the input test and they both show good.

Please help

Jerry

Hiya. I had a similar problem on a 1000 e series. If the batt on the ram board is completely dead, a code 6 appears until the batt builds up a minimum amount of charge.
I had another batt that was just slightly better (1.6 volts) and worked fine after the change
The machine normally throws a code 6 when there is a ram board problem

As long as the board eventually gets past the error 6 code then the ram chips are probably ok.

Remove the ram board and take a small wire brush to the pins that the board mounts to. I normally do both sides of
both rows. Inspect the inside of the edge connectors, those can get corroded as well. You can clean them (somewhat)
by running a bare wire from the bottom up a couple of times on each pin.

Next flip the MPU board over and re-flow some fresh solder on those connecting pins.


I have and a few boards where this resolved the problem. Doesn't work every time but well worth the effort
to make sure

Thanks for the reply. I swapped the MPU board and the new board is working perfectly. My big problem is still the progressive. I just can't get in to set up mode. All the suggestions that have been given don't work.  I'm willing to try anything at this point.

Jerry

Perhaps this documentation will help. I know it says E2000 but should be the same for an E1000 and maybe you have already
tried this procedure as well.

Hi,
I tried those procedures about 100 times. It just doesn't work on my machine. My progressive works, it just starts at zero and increases just like it should. I just can't get the meter to ever show anything other than 800000.
I've checked the buttons in the input test, they check ok.
Is there any special procedure for an E1000 machine which is different than an E2000?

http://newlifegames.net/nlg/index.php?topic=6260.0 (http://newlifegames.net/nlg/index.php?topic=6260.0)

Check this topic and see if it helps.

Also read somewhere about removing the 5101 IC's on the RAM board to reset the memory? As a way to fix the problem.


In this post is about removing the 5101"s and reinstalling them to do a memory reset.

http://newlifegames.net/nlg/index.php?topic=4787.0 (http://newlifegames.net/nlg/index.php?topic=4787.0)

Also read you need 5 PROMS to make the Progressive work.