|
Title: DBV 200 Troubles in Bally 5500 """FIXED it was the HARNESS""" Post by: AcePeter on April 28, 2009, 11:13:46 PM Thanks to all ( StatFreak ) it was the harness and a special thanks to Buzz :3- :131- who sent me one ( a Harness ) Well I looked and read all the post for my problem and still can't get it to work. The DBV-200 works in my other Bally 5500 ( I tested it ) and on this machine I can't figure it out. I turn the machine on. I feed it a bill and it takes it and it will not give credits, then after a few seconds of doing this it beeps then flashes red. The board is good too. Anyone have any other ideals to why this is happening?....Thanks for taking the time to read...
Title: Re: DBV 200 Troubles in Bally 5500 Post by: StatFreak on April 28, 2009, 11:33:43 PM Bad wiring harness? Just a thought, as similar behavior happened to mine and that was the cause.
Title: Re: DBV 200 Troubles in Bally 5500 Post by: AcePeter on April 28, 2009, 11:57:00 PM Thanks I'll give that a try....
Title: Re: DBV 200 Troubles in Bally 5500 Post by: blueridgeslots on April 29, 2009, 02:55:14 AM Did you try flipping Dipswitch 10
Title: Re: DBV 200 Troubles in Bally 5500 Post by: AcePeter on April 29, 2009, 08:26:10 AM Yes still no change (dip switch ). I'm gonna look into the harness that plugs into the motherboard and hopefully that will do it.
Thanks for your time... Title: Re: DBV 200 Troubles in Bally 5500 Post by: AcePeter on May 02, 2009, 11:02:10 AM Well I changed the power supply and back plane and still no credits when I insert bill..I'm guessing it is the harness itself......Thanks to all that replied.... :103-
Title: Re: DBV 200 Troubles in Bally 5500 Post by: Ozzy on May 02, 2009, 12:07:16 PM Hi mate
One thing you might want to try is swapping IC U25 and IC U34 with each other on the MPU, also on the harness check out the grey wiring pin out (BV connector to Back Plane) against a good machine. Had exactly same problem some years back but did no document it. Good luck. cheers O Z ZY Title: Re: DBV 200 Troubles in Bally 5500 Post by: AcePeter on May 03, 2009, 11:48:34 AM Thanks Ozzy
I'll give it a shot and report back.....................OUT Title: Re: DBV 200 Troubles in Bally 5500 """FIXED it was the HARNESS""" Post by: AcePeter on May 09, 2009, 09:50:27 PM Thanks to all ( StatFreak ) it was the harness and a special thanks to Buzz :3- :131- who sent me one ( a Harness )
Title: Re: DBV 200 Troubles in Bally 5500 """FIXED it was the HARNESS""" Post by: stayouttadabunker on May 09, 2009, 10:08:35 PM I so happy you got it going Ace! :89- Good job all! :3-
Title: Re: DBV 200 Troubles in Bally 5500 """FIXED it was the HARNESS""" Post by: tacman on May 10, 2009, 09:46:05 AM Very nice, glad to hear you got it fixed! :3-
Dan (tacman) Title: Re: DBV 200 Troubles in Bally 5500 """FIXED it was the HARNESS""" Post by: StatFreak on May 10, 2009, 10:02:47 AM I'm glad that you were able to get the validator up and running. :89- :3- :71-
|