New Life Games Tech Forums

   Can I get someone to give me the length and width of the bottom plate of a S2000 hopper.    Buzz

If you give me time I will measure mine or you can come and check it out for yourself.

6 3/4" x 10 1/8"

Buzz,

   On My S2000 / Vision the plate attached to the actual hopper is 7 3/4 long (deep) by 5 1/4 wide and
the plate the hopper slides into on the base of the machine is 10 1/8 long x 6 3/4 wide

   On my S+ the plate attached to the actual hopper is 8 1/4 long (deep) by 5 1/2 wide and
the plate the hopper slides into on the base of the machine is 9 1/8 x 9 1/4


The rails the hopper slides on are exact opposites between the S2000 and the S+ so they can't be interchanged

Joe - Thor777

Thanks to you both.  I ran across about 100 new or near new hoppers and just trying to figure out what they fit. The plug on the back is same as my Game King but the bottom plate is 6 5/8 x 9". I'm shipping one to Bunker tomorrow by the time he finishes bending, twisting and general mod. on it, I'm sure it can be installed on a 747 and used for auto pilot   Buzz

Do you have any pictures of the hoppers?

OK  what does this hopper go in?  Buzz

A machine, I would think......  :96- :97- :97- :97-

lol....yes, the million dollar question....but which machine?

   Hey Buzz, Mabey they go in somekind of old vending or coke machine..  :103- (what a pay out !)  :97-  or just Mabey they had a BAD DAY at the factory in quality control??  :24-

Joe  :88-

It has that slanky S connector which is used on IGT and Bally, I would say it would be from an Electrical Mechanical - perhaps an M series or Bally E

with an optic on it?

I am not sure what machine it's from but does it have a PCB board on it?

  In all seriousness Buzz.. Have you tried looking up ANY information written on the hopper or numbers on GOOGLE... It just might lead you to a few clues as this has worked well for me before

Jay  The thing is, this hopper is brand new  and is one of about a 100 that they have  A small tag reads  Bergmann PO# 15902    400237 Rev B  OP 11/02  
       The freight handling co that have these hoppers receive and ship complete slot machines from and to Casio's  over seas. ( last week there were 10 S2000 being shipped back to Reno)  
       30 or 40 Aristocrat and a few Bally 6000    some way the shipping co became owners of these hoppers and they want their wearhouse cleaned out.  I had hope they fit S2000 guess
       not.

 Slotmaster  No board of any kind but if you look at the PIC a 3" arm goes from coin out side to the rear of hopper  there is a optic  (white plastic )

Thor  Joey had your idea maybe it goes  to a change machine But the hopper I grabbed is for a Dollar, who drops a silver dollar in a machine to get change.  ( not all of them are dollar hoppers

  I do thank all of you  Buzz

There should be a number on the CSA (Canadian Safety Association) that may identify it.
I was just looking at the mechanical motor and I had not seen anything like that on my S+ so I guessed it was older.
I had thought you knew and were asking us to guess.... So I guess I don't get the Tshirt.

Perhaps its for the Aristocrats. Their engineers came from same origins as the Ballys and IGTs.
My Aristocat Toppers also have that same connector.

I was commenting that it cant be an EM since it had and optic on it.

we can say for sure it's not Bally, WMS or IGT.

Jay  On the CSA sticker  NRTL/C   HI    No numbers   sure seems to be a lot of work to bring these things home just to get some pin and shelf wheels Assuming they will fit anything.
       NO TEESHIRT    Buzz

  Count CDS out  Buzz

It IS a mystery where these hoppers go into, isn't it?
I'm leaning towards these hoppers fitting Aristrocrats because I've never seen one, or a Sigma perhaps?

I know what it is......


Did I win a prize ? ? ?



It's beer money    :151- :154- :148- :56- :126-

I send this stuff to the scrap metal place along with old machines to support my bad habits.

 :172-

I'm stunned that no one here recognizes them!

If you guys don't know then no one does.

You're gonna make people cry with that RT Williams dotmation in there!

 Dan (tacman)

It made me cry doing it.  :37- :8-
I did steal parts out if them first.