|
Title: Need help Post by: DreamMaster on July 25, 2009, 02:28:00 AM I Have just purchased a new/used MKV machine.
I already own a WMS550 and IGT GameKing, so I have some tech savy. Upon turning on the machine, I have figured out you have to hold down the three lit buttons. However, the BV wouldn't accept, although no error was showing. I have tried using two option set chips in U7 and U11, and have tried a clear chip that I'm not sure is even the right version. I now have the following 4 errors: Memory error Mechanical meters disconnected Door open - bill acceptor Mermory error - game eproms changed Not as easy to figure out as a Gameking without a manual...sigh* Any help would be most appreciated as I had my heart set on taking this baby for a spin this weekend. :99- :103- Title: Re: Need help Post by: tacman on July 25, 2009, 10:36:17 AM DreamMaster, welcome to NLG! I don't own an Aristocrat, but I would venture to say that the machine might have to be cleared due to the Memory Error-game eproms changed, don't know if there is a "soft" clear on the MKV or if you need a clear chip for this. I'm sure one of the other member with more expertise will comment. The Door Open-BV is probably your cash can door that is not closing all the way or jarring open a little when you close the main door., check to make sure its closed and activating the switch. On the meters disconnected, find your meters (hopefully they are there) make sure they have a harness connected and then backtrack the harness and ensure its connected on the other end. Again, I do not know if there is a mod that can be done to the MKV to eliminate the meters, but if so, I'm sure another member will chime in. Good Luck!
Dan (tacman) Title: Re: Need help Post by: DreamMaster on July 26, 2009, 04:11:31 PM Thanks
I have three other boards that I purchased as spares with software. So I tried them all. I had the one game up and running but the battery is low and it died. There was no "meters disconnected" issue, so I confirmed the meters are connected. I also traced the wires and all appears well there. The door one ..... might be just telling me that it was opened. I'm thinking my clear chip might not be the right one at this point. I have two setup options chips that I put in U7 and U11 and they appeared to work as I was able to access the menu. Can someone verify if the clear chip goes into the U7 spot. Also, what is the normal startup procedure that the machine goes through? I had to hold down three buttons that were lit up on boot. Then two different buttons lit up. By holding them down simultaneously, it would advance to the next screen. Also, a copy of the manual would be very helpful. Brad Title: Re: Need help Post by: hoppy on August 05, 2009, 05:50:59 AM Have you tried
open the secrity cage door Turrn the audit key clockwise (should display setup instructions)( does for AU machines) Turning jackpot key clockwise, also may clear some errors cheers Title: Re: Need help Post by: riocarnaval on August 09, 2009, 06:50:14 AM Talking about the Clear Chips; I can tell I also have a problem with 540MKV5.
My goal was to change the denom and to adjust the machine to give 10 credits per token; as I was able to adjust two of my Aristocrats I can not adjust two other. I think I have the wrong chksm for Enchanted Forest and Wild Cougar. Any chance to find out if I am using the correct Clear Chips? Title: Re: Need help Post by: hoppy on August 15, 2009, 02:00:06 AM hi
Information about Australian Mk5 machines. (they operate by different architecture to US) but the following should be similar in type When battery has gone flat the meter data is no longer correct so you will need to do a reset of the static Ram to start meters from 0 again, and also to reload game information from proms.(accounting necessity) Also when making any changes to game denominator the board game credits must be set to 0 (again preserving the correct metering values on the board) else the machine will not allow access to any sensitive menus. Make board credit 0 by (a) playing the credit to 0 (B) Jackpot key payout. The info you require is in the manual 540MVPServiceManual.pdf I see that it is in the submit files section now check chapter 3 ( 3.11)( 3.12) cheers Will try to add photos of setup screesn later. I hope this may be of some use. all reset functions are done with the security cage door open. Main door open, and the security key switch turned clockwise. I have attached photo of Enchanted Forest chipset. The checksum is the middle 4 numbers in the lower set of 12 numbers |