|
Title: Question about bell for PE Slant Top Post by: Jimise on September 19, 2009, 09:04:28 PM Hello all, Does anyone have a Slant top PE+ Video Poker with a Jackpot bell in it?
The manual I have does not show any info about slant tops. If anyone could possibly help me out as to where it hooks up to, Or plugs into? That would be much appreciated! Thanks for all the help! Jim........ :131- Title: Re: Question about bell for PE Slant Top Post by: jaeckleint on September 19, 2009, 10:53:53 PM Guess you found you bell :3- :3- Can figure out where to plug mine in either (s+ round top) :103- :103-
Title: Re: Question about bell for PE Slant Top Post by: Foster on September 19, 2009, 11:27:57 PM Connector for Bell on the motherboard is:
S+ Upright -- J11 Slant Top -- J14 PE+ -- J14 S2000/Vsiion -- Cabinet connector J135 Orange and Yellow/brown wires, most likely either hanging loose or wire tied to other wires near the cabinet I/O Title: Re: Question about bell for PE Slant Top Post by: jaeckleint on September 19, 2009, 11:54:42 PM Thank you very much :131- :3-
Title: Re: Question about bell for PE Slant Top Post by: Jimise on September 20, 2009, 12:51:47 AM Cool, So the upright and the slant top are the same connector.
Well I stuck my head inside the machine and found J14 ! Thank you for the info Foster!! Now I just need to find a plug that fits into J14 :96- Title: Re: Question about bell for PE Slant Top Post by: Foster on September 20, 2009, 02:20:27 AM As long as J14 a 2 pin you should be fine.
Title: Re: Question about bell for PE Slant Top Post by: Jimise on September 20, 2009, 02:57:54 AM Yes, J14 is a 2 pin on the board, But the plug on the bell is different. :103-
Looks like another wire goes in between the board and the bell. Thanks!!! Jim.. As long as J14 a 2 pin you should be fine. Title: Re: Question about bell for PE Slant Top Post by: Foster on September 20, 2009, 05:38:27 AM IGT did the same on the S+.
Title: Re: Question about bell for PE Slant Top Post by: jaeckleint on September 20, 2009, 11:38:32 AM Looks like we need to make a jumper harness. I will check around radio shack and see if I can find the correct plugs to make the harness. Mine needs to be about foot long , how about yours
Title: Re: Question about bell for PE Slant Top Post by: Jimise on September 20, 2009, 02:27:10 PM That sounds like a good idea!! A foot looks pretty close for mine, I think I would go for about 2 feet just for a bit more room to play with.Thanks for the info!!
Looks like we need to make a jumper harness. I will check around radio shack and see if I can find the correct plugs to make the harness. Mine needs to be about foot long , how about yours Title: Re: Question about bell for PE Slant Top Post by: jaeckleint on September 22, 2009, 11:44:04 PM Checked a couple of places and nobody local carrys the plug we need for the bell harness. Radio shack has one close but it is too big and they do not offer the smaller one. I have one more place to check but can"t get there till the weekend. After that...cut off the plug and improvise :5- :5-
Title: Re: Question about bell for PE Slant Top Post by: stayouttadabunker on September 23, 2009, 12:25:58 AM The 2 pins are actually soldered directly to the motherboard...
if you carefully remove the motherboard and place it on a benchtop, under good lighting and magnification, you can carefully lift the black plastic housing up cleanly off the pins without pulling the pins out of the motherboard and use female sockets instead going to the bell... OR You can pick them up at mouser.com Click on the link below, open the sheet and look down on the left hand corner.... You'll see the 2-pin housing... Type in the manufacturer number in the search box at mouser and you'll see it pop up for .11 cents apiece. On the right hand corner of the catalog page you'll see the female crimp-style receptor pins that will fit your pins on the motherboard. Remember, the 2-pin circuit is your "circuit size". The EDP number is: 50-57-9402. Type that number into the search box.... Here's some links to what you're looking for next time you want stuff! :89- http://www.mouser.com/ProductDetail/Molex/50-57-9402/?qs=u6Gr9%2fNt%252b%2f9jh%2fRowNBxRQ%3d%3d (http://www.mouser.com/ProductDetail/Molex/50-57-9402/?qs=u6Gr9%2fNt%252b%2f9jh%2fRowNBxRQ%3d%3d) Title: Re: Question about bell for PE Slant Top Post by: jaeckleint on September 23, 2009, 12:47:12 AM Connection at motherboard not a problem...The connection to the bell harness that is at least a foot short is a 2 pin molex mini connector square one end and and pointed other end total of 3/8" wide that is the problem. We could just lop it off :5- but were trying to keep it neet and OEM looking. And if I want to sell the bell (or if my widowed wife does :30- :30- :30-) I would like it OEM condition without the connector cut off. :60- Have a big old electronics store not far from here I will try this weekend. They have everything and the price to match :47- But how much could a connector cost :103- :103- :103- Without Happ's shipping :3-
Title: Re: Question about bell for PE Slant Top Post by: stayouttadabunker on September 23, 2009, 01:04:49 AM Really, those are also at mouser too... :25-
I give up...go look in radio shack and see what you'll find. :30- I just order stuff from right here and everything comes to my doorstep in a couple of days... :71- Title: Re: Question about bell for PE Slant Top Post by: Jimise on September 26, 2009, 06:15:44 PM Hello again, Well I got my bell hooked up today! And it is pretty loud :96-
There is a guy here in Lake Havasu with a small business called Havasu Slots. Havasuslots.com Anyway, he had some wiring harnesses from some old machines and we pieced together a connector that plugged in between the bell and the board (J14) So I did not have to cut anything! Thanks to everyone on the board for the help!! :3- Title: Re: Question about bell for PE Slant Top Post by: jaeckleint on September 26, 2009, 06:28:44 PM Does he have another one? :71- :71-
|