|
Title: 65 Error- Mechanical Meters Disconnected Post by: reho33 on March 03, 2010, 01:51:52 AM I just got a new board for my S6000 and did a complete Ram clear. I am using 2003 mains. I get a 65 error which the manual says "Mechanical meters disconnected" for the following market codes:3,4,12,28, and 29. When I set the DS3 switches for like NV or NJ markets, it still persists. Suggestions?
Title: Re: 65 Error- Mechanical Meters Disconnected Post by: stayouttadabunker on March 03, 2010, 02:12:14 AM One obvious question comes to mind...
Since it wasn't mentioned - are there any mechanical meters in the machine? Hmm... :129- If there is, then I'd keep trying different markets until; it goes away OR Check the meter wiring perhaps? The easiest one to try is to try un-plugging and re-plugging in the meter harness molex... bad pins inside there maybe? Or just see if you can get new connections with those pins... Plugging & unplugging works miracles sometimes! Title: Re: 65 Error- Mechanical Meters Disconnected Post by: reho33 on March 03, 2010, 02:18:28 AM Stout, no meters in the machine- remember- I'm gettin this ready for you. So I will try different markets to see if it goes away.
Title: Re: 65 Error- Mechanical Meters Disconnected Post by: a69mopar on March 03, 2010, 02:25:46 AM you can use older mains without the meters. I believe there is a hack for this but can't remember it now. sort of like jumping the meter wiring on an iGame if I recall. Meters shouldn't be hard to find though.
Thanks, Wayne Title: Re: 65 Error- Mechanical Meters Disconnected Post by: stayouttadabunker on March 03, 2010, 02:30:41 AM I will dig around tomorrow for the meter hack...
basically it was just a loop jumper wire back into the backplane I believe. Title: Re: 65 Error- Mechanical Meters Disconnected Post by: a69mopar on March 03, 2010, 02:31:34 AM Arizona/Special
International 07 try market code 7 W ( I'm on cold medicine now, have to hit the hay) Title: Re: 65 Error- Mechanical Meters Disconnected Post by: stayouttadabunker on March 03, 2010, 02:35:07 AM Get to bed dude! :149-
Get better soon! :14- Title: Re: 65 Error- Mechanical Meters Disconnected Post by: StatFreak on March 03, 2010, 08:05:53 AM Arizona/Special International 07 try market code 7 W ( I'm on cold medicine now, have to hit the hay) Get to bed dude! :149- :212- :215- :159-Get better soon! :14- Come back after you've punched the straw. :5- SF :31- Title: Re: 65 Error- Mechanical Meters Disconnected Post by: CaptainHappy on March 03, 2010, 09:57:25 AM BEFORE:
:47- :40- :86- :27- :27- AFTER: (Hopefully!!!) :88- :89- :91- :219- :239- :158- :136- :248- :247- :133- :39- ;D ;) :D :109- :21- CH :95- Title: Re: 65 Error- Mechanical Meters Disconnected Post by: reho33 on March 03, 2010, 04:25:09 PM Ok will try MKT code 7. I need the 2003 mains because of the ticket printer.........but lets see how it goes. -R
Update- No dice (ha ha). I am going to try the mains that came with the board to see if it clears up - they have 2006 as date code. Update #2 - Ok , after a full ram clear, the machine is alive again but using the mains that came with it. Update #3 - I am back to my original Bally S6000 board and moved the DIP blocks over to my old board and set the dips according to the jumper block positions and now I am working but it still won't accept coin. But I can live with that. |