Welcome, Guest. Please login or register.
November 22, 2024, 02:38:04 AM

Login with username, password and session length
* Home Help Arcade Login Register
.
+  Forum
|-+  General NLG Chat
| |-+  The Slot Shop **Tech Talk**
| | |-+  question about voltage regulators		 0 Members and 1 Guest are viewing this topic. « previous next »
Pages: 1 [2] Go Down Print
Author Topic: question about voltage regulators  (Read 14170 times)
jbshocks
NLG Member 101 to 500 Post
***

Total Karma Storms: 21
Offline Offline

Gender: Male
Posts: 463
« Reply #25 on: October 11, 2011, 01:57:10 AM »
it is for the lm350t   I have seen several of these usage schematics with 1 and .1 uF caps so I was thinking it might be one of those.  The funny thing is that it is clearly in the position of like R1 in the schematic you posted.  I just noticed one of them seems slightly legible and says +10 35.  Maybe + for positive pin 10 uF and 35 volts?  Way to many years since electronics.
Logged
poppo
Contributing Gold NLG Member
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 248
Offline Offline

Gender: Male
Posts: 3266
« Reply #26 on: October 11, 2011, 02:06:14 AM »
I don't think the circuit would work with it in the place of R1 since the regulator needs a voltage divider for feedback. In any case, it's just a filter cap, so I would go with 1uf. Or just leave whatever you have in there since it's working. It probably went bad because of the AC from the bad bridge rectifier and the regulator was also probably putting out some large AC ripple which cooked the polarized cap.
Logged
jbshocks
NLG Member 101 to 500 Post
***

Total Karma Storms: 21
Offline Offline

Gender: Male
Posts: 463
« Reply #27 on: October 11, 2011, 09:45:02 AM »
Poppo,  I should clarify the placement of the cap.  It is parallel to the actual R1 resistor in this case and I have not seen one used like that in the samples.  I guess that it developed some internal resistance and told the regulator to go lower on the voltage.  I guess maybe I should just leave it.  It was probably killed rather than dying on its own.
Logged
poppo
Contributing Gold NLG Member
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 248
Offline Offline

Gender: Male
Posts: 3266
« Reply #28 on: October 11, 2011, 10:22:30 AM »
Quote from: jbshocks on October 11, 2011, 09:45:02 AM
Poppo,  I should clarify the placement of the cap.  It is parallel to the actual R1 resistor in this case and I have not seen one used like that in the samples.  

Hmmm... Does the LM350 have a voltage adjustment pot? If not, perhaps it's a confiruation like this where a fixed resistor is used in place of R2 on this schematic, and then a cap would be in parralel.

You don't have to use a variable resistor for these regulators if the voltage does not have to be exact. You just use a value that will get you the desired output voltage.

But in any case as long as it's working, I would not worry about it.


* LM350.jpg (8.5 KB, 287x193 - viewed 317 times.)
Logged
jbshocks
NLG Member 101 to 500 Post
***

Total Karma Storms: 21
Offline Offline

Gender: Male
Posts: 463
« Reply #29 on: October 11, 2011, 10:46:13 AM »
no pot or diodes involved.  It does have an R2 that goes off into never never land, at least I couldn't determine where it went.  I disconnected the R2 on the extra board and voltage didn't change. 
Logged
Pages: 1 [2] Go Up Print 
« previous next »
Jump to:  

SimplePortal Classic 2.0.5

If you find this site helpful, Please Consider Making a small donation to help defray the cost of hosting and bandwidth.



Newlifegames.com ™    Newlifegames.net ™    Newlifegames.org ™
   New Life Games ™    NewLifeGames ™  NLG ™ We Bring new Life to old Games ™    1-888-NLG-SLOTS ™
Are all Copyright and Trademarks of New Life Games LLC 1992 - 2021


FAIR USE NOTICE:

This site contains copyrighted material the use of which has not always been specifically authorized by the copyright owner.
We make such material available in an effort to advance awareness and understanding of the issues involved.
We believe this constitutes a fair use of any such copyrighted material as provided for in section 107 of the US Copyright Law.
In accordance with Title 17 U.S.C. Section 107, the material on this site is distributed without profit to those
who have expressed a prior interest in receiving the included information for research and educational purposes.

For more information please visit: http://www.law.cornell.edu/uscode/17/107.shtml.

If you wish to use copyrighted material from this site for purposes of your own that go beyond fair use,
you must obtain permission directly from the copyright owner.

NewLifeGames.net Web-Site is optimized for use with Fire-Fox and a minimum screen resolution of 1280x768 pixels.


Powered by SMF 1.1.20 | SMF © 2013, Simple Machines
Loon Designed by Mystica
Updated by Runic Warrior
Page created in 0.139 seconds with 20 queries.