Welcome, Guest. Please login or register.
October 31, 2024, 08:50:34 PM

Login with username, password and session length
* Home Help Arcade Login Register
.
+  Forum
|-+  **Reel Slots** Gaming Machines
| |-+  IGT M Slot Reel Games
| | |-+  Igt m need to reset CMOS error code
0 Members and 1 Guest are viewing this topic. « previous next »
Pages: [1] Go Down Print
Author Topic: Igt m need to reset CMOS error code  (Read 12567 times)
Bdietz
New NLG Member 1 to 100 Post
**

Total Karma Storms: 0
Offline Offline

Posts: 10



« on: July 11, 2013, 10:33:06 PM »

Can anyone tell me how to reset the CMOS error code? The manual says I need to clear the CMOS ram by depressing the switch on the CMOS board but I don't know where this is located. Any help is appreciated!
Logged
hartman
New NLG Member 1 to 100 Post
**

Total Karma Storms: 0
Offline Offline

Posts: 3



« Reply #1 on: July 11, 2013, 11:23:29 PM »

Reset button is a white button located in the lower left area on a vertical board, see the picture included.


* Inside2.jpg (767.43 KB, 1368x1824 - viewed 732 times.)
Logged
Bdietz
New NLG Member 1 to 100 Post
**

Total Karma Storms: 0
Offline Offline

Posts: 10



« Reply #2 on: July 12, 2013, 12:09:44 AM »

Thanks I did find it but now the reels won't spin. It tries to reset but it won't spin.
Logged
hartman
New NLG Member 1 to 100 Post
**

Total Karma Storms: 0
Offline Offline

Posts: 3



« Reply #3 on: July 13, 2013, 02:02:46 AM »

Do you get any error codes in the display?
Can you get into any of the test menus when you push the white button?
Logged
Bdietz
New NLG Member 1 to 100 Post
**

Total Karma Storms: 0
Offline Offline

Posts: 10



« Reply #4 on: July 13, 2013, 10:38:35 AM »

I get no spin 1 as an error. I can get into the test menu but i don't know how to run any tests.
Logged
Neonkiss
Contributing Gold NLG Member
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 436
Offline Offline

Gender: Male
Posts: 2084



« Reply #5 on: July 13, 2013, 11:01:22 AM »

Those reels spin via an electric motor. The timing for the kickers to stop the reels is done with a fiber roller that follows a cam.
Those fiber rollers get worn out and break over time. Many here have replaced them with a bearing. Here is a poor picture of a broken fiber roller. It was taken when cell phones first came with cameras.  Duh!


* IGT M #1.jpg (67.73 KB, 640x480 - viewed 460 times.)
Logged

Nothing brings people together better than a common enemy
343 / 60 brothers lost on that day.
Bdietz
New NLG Member 1 to 100 Post
**

Total Karma Storms: 0
Offline Offline

Posts: 10



« Reply #6 on: July 13, 2013, 11:19:18 AM »

We did replace these rollers on each actuator arm assembly


* image.jpg (204.7 KB, 960x720 - viewed 436 times.)
Logged
Neonkiss
Contributing Gold NLG Member
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 436
Offline Offline

Gender: Male
Posts: 2084



« Reply #7 on: July 13, 2013, 11:28:19 AM »

Ah, Good Job...
Do the reels spin and reset the kickers when power is applied to the machine?
If I remember correctly, the motor spins the reels and the solenoid on the kickers stop the reels in sequence.
The following cam (with your new bearings) just reset the kickers for the next spin.

I posted the wrong sequence in my previous post. Must be CRS
Logged

Nothing brings people together better than a common enemy
343 / 60 brothers lost on that day.
Bdietz
New NLG Member 1 to 100 Post
**

Total Karma Storms: 0
Offline Offline

Posts: 10



« Reply #8 on: July 13, 2013, 12:30:15 PM »

It makes a sound like they are resetting but the reels do not spin and then an error message of call attendant appears.
Logged
Neonkiss
Contributing Gold NLG Member
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 436
Offline Offline

Gender: Male
Posts: 2084



« Reply #9 on: July 13, 2013, 12:43:22 PM »

Is the motor froze up?
Logged

Nothing brings people together better than a common enemy
343 / 60 brothers lost on that day.
gordy
Contributing NLG Member
NLG Member 101 to 500 Post
*

Total Karma Storms: 24
Offline Offline

Gender: Male
Posts: 163



« Reply #10 on: July 13, 2013, 02:39:23 PM »

Error code  ' Reel 1 " means the reel actuator is not working properly.  It is the kicker that spins the reels.  When you get that cleaned and checked and working you will likely get a code for one or more of the actuators.   Isnt this an M+ ?  I have parts for these macines  [ M and M+ ].  Gordy
Logged
Bdietz
New NLG Member 1 to 100 Post
**

Total Karma Storms: 0
Offline Offline

Posts: 10



« Reply #11 on: July 13, 2013, 03:28:33 PM »

No i don't think it is an m+. how difficult is it to clean the kicker and get it working? This is the first time i have tried fixing any slot machine and i could not get the reels to come out only the actuators.
Logged
Bdietz
New NLG Member 1 to 100 Post
**

Total Karma Storms: 0
Offline Offline

Posts: 10



« Reply #12 on: July 13, 2013, 03:29:30 PM »

How do i know if the motor is froze? Is there something i can look at or do I have to test it somehow?
Logged
Bdietz
New NLG Member 1 to 100 Post
**

Total Karma Storms: 0
Offline Offline

Posts: 10



« Reply #13 on: July 13, 2013, 05:45:56 PM »

Ok, i was able to remove the reels and this steel bar dehind it does spin one rotation upon start up of machine.


* image.jpg (276.8 KB, 960x720 - viewed 463 times.)
Logged
Neonkiss
Contributing Gold NLG Member
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 436
Offline Offline

Gender: Male
Posts: 2084



« Reply #14 on: July 13, 2013, 06:13:04 PM »

Good, Now check the kickers.
If reel one is sending an error, try moving that kicker to another position, like 3
Then see if you still get the reel one error or if the error moves to the new location.

Gordy, thanks for correcting me on the proper sequence.
It's been a long time since I had a M series.
Logged

Nothing brings people together better than a common enemy
343 / 60 brothers lost on that day.
gordy
Contributing NLG Member
NLG Member 101 to 500 Post
*

Total Karma Storms: 24
Offline Offline

Gender: Male
Posts: 163



« Reply #15 on: July 13, 2013, 10:35:00 PM »

Neonkiss is better than me.  That is the way to find a bad actuator.  If that procedure works, fine. If it does not , it could be that all 4 actuators are bad.  When they sit,  the grease gets hard.  It takes a long time, but I clean them with carb. cleaner and then use WD 40 and often let it sit for a few hours. Be real careful you dont cloud the optics with spray. Also check the continuity of the actuator wires and the solenoids.  In casinos these were the main problem.
Logged
Bdietz
New NLG Member 1 to 100 Post
**

Total Karma Storms: 0
Offline Offline

Posts: 10



« Reply #16 on: July 14, 2013, 09:17:45 PM »

I tried moving the third actuator to the first position but the same thing happened when i tried to turn on the machine. It goes to reset but nothing turns; however the screen was completely blank so i could not see an error code. Also, i went to switch numbere two with number one and discovered that the brown plastic wire was off (see pic there is a blue wire but the brown plastic wire is missing that goes over it). Is this the problem?


* image.jpg (236.79 KB, 960x720 - viewed 464 times.)
Logged
gordy
Contributing NLG Member
NLG Member 101 to 500 Post
*

Total Karma Storms: 24
Offline Offline

Gender: Male
Posts: 163



« Reply #17 on: July 14, 2013, 11:12:16 PM »

All 4 actuators are wired the same and are interchangeable.  Compare them and you will see where the wires are supposed to go and make them all the same.  Those brown plastic strips become brittle and crack, so you may need to solder new pieces of wire to make connections.  Later machines had stronger wires and discarded the brown plastic ones.
Logged
Bdietz
New NLG Member 1 to 100 Post
**

Total Karma Storms: 0
Offline Offline

Posts: 10



« Reply #18 on: July 14, 2013, 11:56:34 PM »

Since this piece is missing is that most likely why the reels don't spin or do the actuators only stop the reels from spinning? I am just trying to figure out if this is my only issue or have i just begun...

Btw- do you know anyone in the central PA region that can fix these (it is only a 3 reel)?
Logged
gordy
Contributing NLG Member
NLG Member 101 to 500 Post
*

Total Karma Storms: 24
Offline Offline

Gender: Male
Posts: 163



« Reply #19 on: July 15, 2013, 08:17:27 AM »

Pretty hard to answer when I cant see exactly what part is missing.  Chances are I have the part if you can identify it.  Look at another actuator.  If a wire is missing, solder a new one in there.
 The only longshot repair guy in central PA is Tracy Etter  717 732 6022.
   Does the inside of your 3 reeler look like the one Hartman posted ?
Logged
Pages: [1] Go Up Print 
« previous next »
Jump to:  


If you find this site helpful, Please Consider Making a small donation to help defray the cost of hosting and bandwidth.



Newlifegames.com    Newlifegames.net    Newlifegames.org
   New Life Games    NewLifeGames  NLG  We Bring new Life to old Games    1-888-NLG-SLOTS
Are all Copyright and Trademarks of New Life Games LLC 1992 - 2021


FAIR USE NOTICE:

This site contains copyrighted material the use of which has not always been specifically authorized by the copyright owner.
We make such material available in an effort to advance awareness and understanding of the issues involved.
We believe this constitutes a fair use of any such copyrighted material as provided for in section 107 of the US Copyright Law.
In accordance with Title 17 U.S.C. Section 107, the material on this site is distributed without profit to those
who have expressed a prior interest in receiving the included information for research and educational purposes.

For more information please visit: http://www.law.cornell.edu/uscode/17/107.shtml.

If you wish to use copyrighted material from this site for purposes of your own that go beyond fair use,
you must obtain permission directly from the copyright owner.

NewLifeGames.net Web-Site is optimized for use with Fire-Fox and a minimum screen resolution of 1280x768 pixels.


Powered by SMF 1.1.20 | SMF © 2013, Simple Machines
Loon Designed by Mystica
Updated by Runic Warrior
Page created in 0.093 seconds with 20 queries.