Welcome, Guest. Please login or register.
November 23, 2024, 12:37:05 AM

Login with username, password and session length
* Home Help Arcade Login Register
.
+  Forum
|-+  **Reel Slots** Gaming Machines
| |-+  Bally Reel Games. (Moderator: a69mopar)
| | |-+  Clear problems - Bally s5500?		 0 Members and 1 Guest are viewing this topic. « previous next »
Pages: [1] Go Down Print
Author Topic: Clear problems - Bally s5500?  (Read 10844 times)
rjpohl
Contributing Gold NLG Member
Sr.NLG Member 501 to 1000 Post
*

Total Karma Storms: 103
Offline Offline

Gender: Male
Posts: 726



WWW
« on: December 30, 2010, 03:54:03 PM »
I believe I have a bally 5500
S940201928
S63B3WT-10
2/94
6304/GSM-500

board number: AS-3356-201 rev E
mains ME920000-6-0  02/09/05

Had 81 error code.  I replaced battery and then placed jumper on JW10, held test and Pcoin buttons and powered up.  Held buttons for approx 15 seconds but got no display readings.  Powered off back on (hold the 2 buttons in) and I got 83F.  I powered back off and then used clear chips.  Can't get any reading on display.

I did get all 9's in display once but don't remember how.

I've tried the board in another working machine and get the same results.  

What am I doing wrong?????

Thanks
Bob
« Last Edit: December 30, 2010, 06:10:27 PM by rjpohl » Logged

http://samronslots.com/
CVslots
Contributing Gold NLG Member
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 432
Offline Offline

Gender: Male
Posts: 2803



WWW
« Reply #1 on: December 30, 2010, 05:15:19 PM »
I just had a all 9's on a 5500 and it was a bent pin on one of the chips. If you get stuck in a 83F loop after a clear start over and make sure that the MPU board is pushed in all of the way.  I've also had to press really hard on the PSEUDO COIN and TEST buttons, when you switching the power ON, I think they get a little sticky sometimes.

Good luck.
Logged

www.CentralValleySlots.com
Email: centralvalleyslots@yahoo.com
rjpohl
Contributing Gold NLG Member
Sr.NLG Member 501 to 1000 Post
*

Total Karma Storms: 103
Offline Offline

Gender: Male
Posts: 726



WWW
« Reply #2 on: December 30, 2010, 06:11:33 PM »
do I need to use clear chips or the JW10 jumper to perform ram clear on this slot?
Logged

http://samronslots.com/
CVslots
Contributing Gold NLG Member
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 432
Offline Offline

Gender: Male
Posts: 2803



WWW
« Reply #3 on: December 30, 2010, 07:25:47 PM »
With the older mains you should be able to do just a JW10
Logged

www.CentralValleySlots.com
Email: centralvalleyslots@yahoo.com
rjpohl
Contributing Gold NLG Member
Sr.NLG Member 501 to 1000 Post
*

Total Karma Storms: 103
Offline Offline

Gender: Male
Posts: 726



WWW
« Reply #4 on: December 30, 2010, 07:52:11 PM »
I put jumper on JW10
Held test and coin buttons in while turning on power
get CL C
power off
remove jumper, power onf
83F

put clear chips in
power on while holding buttons in
flashing 9's

???????????????
Logged

http://samronslots.com/
paul
paul
Contributing Gold NLG Member
Sr.NLG Member 501 to 1000 Post
*

Total Karma Storms: 20
Offline Offline

Gender: Male
Posts: 548
« Reply #5 on: December 30, 2010, 10:57:16 PM »
did you get ch-c first then cl-c
Logged
rjpohl
Contributing Gold NLG Member
Sr.NLG Member 501 to 1000 Post
*

Total Karma Storms: 103
Offline Offline

Gender: Male
Posts: 726



WWW
« Reply #6 on: December 30, 2010, 11:29:35 PM »
pretty sure I got ch-c first and the cl-c.  I've tried 2 boards with the same mains, I'm thinking I may have bad mains. 
Logged

http://samronslots.com/
paul
paul
Contributing Gold NLG Member
Sr.NLG Member 501 to 1000 Post
*

Total Karma Storms: 20
Offline Offline

Gender: Male
Posts: 548
« Reply #7 on: December 31, 2010, 01:20:42 AM »
check all chips you had out for bent pins remove the chip to check the pins
Logged
CVslots
Contributing Gold NLG Member
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 432
Offline Offline

Gender: Male
Posts: 2803



WWW
« Reply #8 on: December 31, 2010, 02:59:59 AM »
Ok,
I pulled U18 and bent 1 pin and I'm getting a 99999. Check all of your chips, pull and reinsert them.
Logged

www.CentralValleySlots.com
Email: centralvalleyslots@yahoo.com
StatFreak
rotaredoM etiS GLN labolG
Global NLG Site Moderator
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 756
Offline Offline

Gender: Male
Posts: 8549


Warning! Spammers will be eaten, with relish!
« Reply #9 on: December 31, 2010, 03:14:21 AM »
Quote from: CVslots on December 31, 2010, 02:59:59 AM
Ok,
I pulled U18 and bent 1 pin and I'm getting a 99999. Check all of your chips, pull and reinsert them.

Wow CV. We're going to have to award you a purple heart. Oh wait, self inflicted wounds don't count. Crazy bust gut laughing bust gut laughing bust gut laughing
Still,  +1 (Karma, or whatever)  for going the extra mile and deliberately bending your pin for a fellow member. applause applause  frying pan frying pan   
  (Okay peanut gallery, let 'em fly. arrow  3 Stooges    I'm playing straight man tonight. boss)


Stat garfield
Logged
I found myself at NLG garfield  ..but got lost again on the way home. Scratch Head 2
If found, please email me to myself. Thanks. yes
       Executive member in good standing of Rick's SMAA.                              Ehhh...What's Up Doc?
CVslots
Contributing Gold NLG Member
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 432
Offline Offline

Gender: Male
Posts: 2803



WWW
« Reply #10 on: December 31, 2010, 03:51:29 AM »
Curiosity killed the cat, I just had to know. If it were a IGT we wouldn't be making any sacrifices.
Logged

www.CentralValleySlots.com
Email: centralvalleyslots@yahoo.com
StatFreak
rotaredoM etiS GLN labolG
Global NLG Site Moderator
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 756
Offline Offline

Gender: Male
Posts: 8549


Warning! Spammers will be eaten, with relish!
« Reply #11 on: December 31, 2010, 04:00:49 AM »
Quote from: CVslots on December 31, 2010, 03:51:29 AM
Curiosity killed the cat, I just had to know. If it were a IGT we wouldn't be making any sacrifices.

Ouch! Sorry Bally, that had to hurt.    angry-kitty   slap knockout
Logged
I found myself at NLG garfield  ..but got lost again on the way home. Scratch Head 2
If found, please email me to myself. Thanks. yes
       Executive member in good standing of Rick's SMAA.                              Ehhh...What's Up Doc?
rjpohl
Contributing Gold NLG Member
Sr.NLG Member 501 to 1000 Post
*

Total Karma Storms: 103
Offline Offline

Gender: Male
Posts: 726



WWW
« Reply #12 on: December 31, 2010, 07:26:17 AM »
I have pulled all eproms and checked for bent legs (didn't find any) then re-seated in board and got same results.  I have another board that has 1994 mains (ME920000-4-0) and U3 and4 chips that are marked SE92000-5-X.

do the mains (U18 and U20) have to have matching numbers to U3 and4 (920000)?
what is the purpose of the U3 and U4 chips??

is this a S5500 machine or a S5000 (how can I tell from mocel number?)

Thanks CVslots for the "bending the leg" test  Karma+  
« Last Edit: December 31, 2010, 07:33:31 AM by rjpohl » Logged

http://samronslots.com/
rjpohl
Contributing Gold NLG Member
Sr.NLG Member 501 to 1000 Post
*

Total Karma Storms: 103
Offline Offline

Gender: Male
Posts: 726



WWW
« Reply #13 on: December 31, 2010, 10:05:08 AM »
This was driving me crazy so I pulled the chips off the working machine I have and replaced with chips from problem machine and it cleared and worked perfectly in my machine.  Long story short it appears the board in the problem machine and the spare board I had were both bad.  Is there anyone out there that repairs these?

thanks for all the help
Bob
Logged

http://samronslots.com/
jdkmunch
Senior Full time Member.
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 624
Offline Offline

Gender: Male
Posts: 2640
« Reply #14 on: December 31, 2010, 03:18:11 PM »
Quote from: rjpohl on December 31, 2010, 07:26:17 AM

is this a S5500 machine or a S5000

Can you post a picture?  I can tell from looking at it.
Sounds like a 5500 to me
Logged
StatFreak
rotaredoM etiS GLN labolG
Global NLG Site Moderator
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 756
Offline Offline

Gender: Male
Posts: 8549


Warning! Spammers will be eaten, with relish!
« Reply #15 on: December 31, 2010, 08:40:20 PM »
Quote from: jdkmunch on December 31, 2010, 03:18:11 PM
Quote from: rjpohl on December 31, 2010, 07:26:17 AM

is this a S5500 machine or a S5000

Can you post a picture?  I can tell from looking at it.
Sounds like a 5500 to me

I agree. Replacing the board is probably cheaper and easier than having yours repaired.
Logged
I found myself at NLG garfield  ..but got lost again on the way home. Scratch Head 2
If found, please email me to myself. Thanks. yes
       Executive member in good standing of Rick's SMAA.                              Ehhh...What's Up Doc?
paul
paul
Contributing Gold NLG Member
Sr.NLG Member 501 to 1000 Post
*

Total Karma Storms: 20
Offline Offline

Gender: Male
Posts: 548
« Reply #16 on: December 31, 2010, 08:51:14 PM »
Bob U 18 and U20 are game chips
Logged
rjpohl
Contributing Gold NLG Member
Sr.NLG Member 501 to 1000 Post
*

Total Karma Storms: 103
Offline Offline

Gender: Male
Posts: 726



WWW
« Reply #17 on: December 31, 2010, 09:36:41 PM »
Quote from: paul on December 31, 2010, 08:51:14 PM
Bob U 18 and U20 are game chips
[/quote

do the game chips have to match U3 & U4?  what are u3 and u4?
Logged

http://samronslots.com/
paul
paul
Contributing Gold NLG Member
Sr.NLG Member 501 to 1000 Post
*

Total Karma Storms: 20
Offline Offline

Gender: Male
Posts: 548
« Reply #18 on: December 31, 2010, 10:03:56 PM »
No it is 3--4--12--15 
Logged
junkman
NLG Member 101 to 500 Post
***

Total Karma Storms: 2
Offline Offline

Gender: Male
Posts: 220
« Reply #19 on: January 01, 2011, 12:28:06 AM »
When I replaced battery I had to let the machine stay on for half day to let the battery charge. And yes it was a new battery. Then I could clear ram.
Logged
Always remember when you leave the house keep your eye's open.
StatFreak
rotaredoM etiS GLN labolG
Global NLG Site Moderator
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 756
Offline Offline

Gender: Male
Posts: 8549


Warning! Spammers will be eaten, with relish!
« Reply #20 on: January 01, 2011, 01:44:49 AM »
Quote from: junkman on January 01, 2011, 12:28:06 AM
When I replaced battery I had to let the machine stay on for half day to let the battery charge. And yes it was a new battery. Then I could clear ram.

The battery does not charge when the power is on; it is a non-rechargeable lithium battery. I'm not sure why you had to wait. Scratch Head 2
Logged
I found myself at NLG garfield  ..but got lost again on the way home. Scratch Head 2
If found, please email me to myself. Thanks. yes
       Executive member in good standing of Rick's SMAA.                              Ehhh...What's Up Doc?
Pages: [1] Go Up Print 
« previous next »
Jump to:  

SimplePortal Classic 2.0.5

If you find this site helpful, Please Consider Making a small donation to help defray the cost of hosting and bandwidth.



Newlifegames.com ™    Newlifegames.net ™    Newlifegames.org ™
   New Life Games ™    NewLifeGames ™  NLG ™ We Bring new Life to old Games ™    1-888-NLG-SLOTS ™
Are all Copyright and Trademarks of New Life Games LLC 1992 - 2021


FAIR USE NOTICE:

This site contains copyrighted material the use of which has not always been specifically authorized by the copyright owner.
We make such material available in an effort to advance awareness and understanding of the issues involved.
We believe this constitutes a fair use of any such copyrighted material as provided for in section 107 of the US Copyright Law.
In accordance with Title 17 U.S.C. Section 107, the material on this site is distributed without profit to those
who have expressed a prior interest in receiving the included information for research and educational purposes.

For more information please visit: http://www.law.cornell.edu/uscode/17/107.shtml.

If you wish to use copyrighted material from this site for purposes of your own that go beyond fair use,
you must obtain permission directly from the copyright owner.

NewLifeGames.net Web-Site is optimized for use with Fire-Fox and a minimum screen resolution of 1280x768 pixels.


Powered by SMF 1.1.20 | SMF © 2013, Simple Machines
Loon Designed by Mystica
Updated by Runic Warrior
Page created in 0.104 seconds with 19 queries.