Welcome, Guest. Please login or register.
November 26, 2024, 07:08:57 PM

Login with username, password and session length
* Home Help Arcade Login Register
.
+  Forum
|-+  **Reel Slots** Gaming Machines
| |-+  Bally Reel Games. (Moderator: a69mopar)
| | |-+  Bally 5500 problem		 0 Members and 1 Guest are viewing this topic. « previous next »
Pages: [1] Go Down Print
Author Topic: Bally 5500 problem  (Read 10227 times)
toms5500
Guest
« on: February 19, 2011, 01:14:09 AM »
Help-I have a Bally 5500 triple reel machine. Error F81 came up. I got and replaced the battery then got 83F so I got clear chips. I followed the procedure in the original Bally manual. While holding the buttons down I herd different things so thought all was well. After 10 minutes of silence and no messages in the paid message area the red reset light came on flashing. I tried the entire procedure over again with no results-just the red flashing reset light on. The second time, the clear chips were quite hot. Did I fry the board or what? Appreciate any help. thanks.
Logged
a69mopar
647-402-1977
Global NLG Site Moderator
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 600
Offline Offline

Gender: Male
Posts: 3508



WWW
« Reply #1 on: February 19, 2011, 02:32:02 AM »
That's possible, or maybe just the Saferam clear chips.  You may have inserted the chips backwards.  Did you try putting the mains back in to see if you get a code?

Thanks,
Wayne
Logged
         www.GTASLOTS.com      647-402-1977              BALLY S6000 GALLERY
stayouttadabunker
Senior Full time Member.
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 1039
Offline Offline

Gender: Male
Posts: 13447
« Reply #2 on: February 19, 2011, 05:00:12 AM »
Clear chips hot...uh oh... Burning Resistor
Don't need salsa... arrow
Logged
toms5500
Guest
« Reply #3 on: February 19, 2011, 02:57:02 PM »
the chips were in the correct spots. Now when I put the main chips in I get no error codes but the machine doesn't work either.
Logged
a69mopar
647-402-1977
Global NLG Site Moderator
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 600
Offline Offline

Gender: Male
Posts: 3508



WWW
« Reply #4 on: February 19, 2011, 03:56:03 PM »
Quote from: toms5500 on February 19, 2011, 02:57:02 PM
the chips were in the correct spots.
and correct direction?

Regardless, you may need a main board now. any traces burned off near the back of the board? 

Thanks,
Wayne
Logged
         www.GTASLOTS.com      647-402-1977              BALLY S6000 GALLERY
toms5500
Guest
« Reply #5 on: February 19, 2011, 04:42:37 PM »
I put the chips in with printing pointed in the same direction as the main chips. No burns. Like I said all I get is the blinking reset light. Thanks.
Logged
StatFreak
rotaredoM etiS GLN labolG
Global NLG Site Moderator
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 756
Offline Offline

Gender: Male
Posts: 8549


Warning! Spammers will be eaten, with relish!
« Reply #6 on: February 19, 2011, 05:20:30 PM »
Quote from: toms5500 on February 19, 2011, 04:42:37 PM
I put the chips in with printing pointed in the same direction as the main chips. No burns. Like I said all I get is the blinking reset light. Thanks.

Although original stickers would usually be oriented in the same direction, the printing direction is irrelevant. Never use the stickers as an installation guideline! You must install them with the NOTCH on the end of the chip matching the notch that is on the socket and printed on the board beneath.
Logged
I found myself at NLG garfield  ..but got lost again on the way home. Scratch Head 2
If found, please email me to myself. Thanks. yes
       Executive member in good standing of Rick's SMAA.                              Ehhh...What's Up Doc?
a69mopar
647-402-1977
Global NLG Site Moderator
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 600
Offline Offline

Gender: Male
Posts: 3508



WWW
« Reply #7 on: February 19, 2011, 05:30:00 PM »
One more thing,
Check the pins at the connectors at rear of board to see if any got bent

W
Logged
         www.GTASLOTS.com      647-402-1977              BALLY S6000 GALLERY
StatFreak
rotaredoM etiS GLN labolG
Global NLG Site Moderator
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 756
Offline Offline

Gender: Male
Posts: 8549


Warning! Spammers will be eaten, with relish!
« Reply #8 on: February 19, 2011, 05:32:38 PM »
Quote from: a69mopar on February 19, 2011, 05:30:00 PM
One more thing,
Check the pins at the connectors at rear of board to see if any got bent

W

Thanks Wayne. I was about to post that, but then I read that he used the stickers as an installation guide and I forgot..  arrow rotflmao
Logged
I found myself at NLG garfield  ..but got lost again on the way home. Scratch Head 2
If found, please email me to myself. Thanks. yes
       Executive member in good standing of Rick's SMAA.                              Ehhh...What's Up Doc?
toms5500
Guest
« Reply #9 on: February 20, 2011, 02:41:44 PM »
Checked. Chips in correct. no bent pins.
Logged
a69mopar
647-402-1977
Global NLG Site Moderator
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 600
Offline Offline

Gender: Male
Posts: 3508



WWW
« Reply #10 on: February 20, 2011, 09:24:50 PM »
odd that they heated up then.  There is an untested as is board on eBay.  you may want to test your power supply first though.

Thanks,
Wayne
Logged
         www.GTASLOTS.com      647-402-1977              BALLY S6000 GALLERY
kenokarz
Contributing Gold NLG Member
NLG Member 101 to 500 Post
*

Total Karma Storms: 284
Offline Offline

Gender: Male
Posts: 470
« Reply #11 on: February 20, 2011, 09:43:18 PM »
on a bally 5500 i have never had to use clear chips just moved the jumper,  Scratch Head Scratch Head
Logged
StatFreak
rotaredoM etiS GLN labolG
Global NLG Site Moderator
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 756
Offline Offline

Gender: Male
Posts: 8549


Warning! Spammers will be eaten, with relish!
« Reply #12 on: February 26, 2011, 09:43:49 AM »
Quote from: kenokarz on February 20, 2011, 09:43:18 PM
on a bally 5500 i have never had to use clear chips just moved the jumper,  Scratch Head Scratch Head

It depends on which version of Mains you have installed. The 920000 series don't need clear chip; the 950000 series do.
« Last Edit: February 26, 2011, 09:49:20 AM by StatFreak » Logged
I found myself at NLG garfield  ..but got lost again on the way home. Scratch Head 2
If found, please email me to myself. Thanks. yes
       Executive member in good standing of Rick's SMAA.                              Ehhh...What's Up Doc?
StatFreak
rotaredoM etiS GLN labolG
Global NLG Site Moderator
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 756
Offline Offline

Gender: Male
Posts: 8549


Warning! Spammers will be eaten, with relish!
« Reply #13 on: February 26, 2011, 09:47:26 AM »
Quote from: toms5500 on February 20, 2011, 02:41:44 PM
Checked. Chips in correct. no bent pins.

Did you ever solve your problem? If not, don't forget a69mopar's post, which I copied below. If that's not the problem, we'll take it from there.


Quote from: a69mopar on February 19, 2011, 05:30:00 PM
One more thing,
Check the pins at the connectors at rear of board to see if any got bent

W
Logged
I found myself at NLG garfield  ..but got lost again on the way home. Scratch Head 2
If found, please email me to myself. Thanks. yes
       Executive member in good standing of Rick's SMAA.                              Ehhh...What's Up Doc?
toms5500
Guest
« Reply #14 on: March 03, 2011, 12:12:57 AM »
Toms5500 here again. I got a new board but same results-all I get is a flashing reset light on the board. No effect from pushing reset button. I had to transfer u18 and u20 chips from old board. Chips in correct, no bent pins in board. Could the 18 and 20 chips be bad. Power supply no good or what? Appreciate the help-really like this site.
Logged
paul
paul
Contributing Gold NLG Member
Sr.NLG Member 501 to 1000 Post
*

Total Karma Storms: 20
Offline Offline

Gender: Male
Posts: 548
« Reply #15 on: March 03, 2011, 01:08:27 AM »
whatis the date on U3  U4    U12   U15
Logged
toms5500
Guest
« Reply #16 on: March 03, 2011, 01:22:10 AM »
On the new board there are no dates. On the old board the dates are 9/25/97. Thanks.
Logged
kenokarz
Contributing Gold NLG Member
NLG Member 101 to 500 Post
*

Total Karma Storms: 284
Offline Offline

Gender: Male
Posts: 470
« Reply #17 on: March 03, 2011, 01:45:24 AM »
are all the jumpers on the new board same as old one ???
Logged
toms5500
Guest
« Reply #18 on: March 03, 2011, 02:04:18 AM »
The jumpers are the same.
Logged
toms5500
Guest
« Reply #19 on: March 03, 2011, 02:13:40 AM »
I have just noticed that in the new board there is a u68 chip but none in the old board. Also, I have been asked where I am-I am in cold Minnesota.
Logged
a69mopar
647-402-1977
Global NLG Site Moderator
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 600
Offline Offline

Gender: Male
Posts: 3508



WWW
« Reply #20 on: March 05, 2011, 01:39:56 AM »
Was this a tested working board or an as is board?  I never trust untested as is boards since I'm sure most have been tested but haven't passed.

Thanks,
Wayne
Logged
         www.GTASLOTS.com      647-402-1977              BALLY S6000 GALLERY
toms5500
Guest
« Reply #21 on: March 05, 2011, 04:25:50 PM »
It was a tested board I got from Rudys Steals. I talked with John and he sending me new game chips to try. If that doesn't work We are going to try a new power supply.
Logged
a69mopar
647-402-1977
Global NLG Site Moderator
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 600
Offline Offline

Gender: Male
Posts: 3508



WWW
« Reply #22 on: March 06, 2011, 05:07:11 PM »
For some reason I had thought you had tested the power supply voltages.  OK, good luck.

Thanks,
Wayne
Logged
         www.GTASLOTS.com      647-402-1977              BALLY S6000 GALLERY
Pages: [1] Go Up Print 
« previous next »
Jump to:  

SimplePortal Classic 2.0.5

If you find this site helpful, Please Consider Making a small donation to help defray the cost of hosting and bandwidth.



Newlifegames.com ™    Newlifegames.net ™    Newlifegames.org ™
   New Life Games ™    NewLifeGames ™  NLG ™ We Bring new Life to old Games ™    1-888-NLG-SLOTS ™
Are all Copyright and Trademarks of New Life Games LLC 1992 - 2021


FAIR USE NOTICE:

This site contains copyrighted material the use of which has not always been specifically authorized by the copyright owner.
We make such material available in an effort to advance awareness and understanding of the issues involved.
We believe this constitutes a fair use of any such copyrighted material as provided for in section 107 of the US Copyright Law.
In accordance with Title 17 U.S.C. Section 107, the material on this site is distributed without profit to those
who have expressed a prior interest in receiving the included information for research and educational purposes.

For more information please visit: http://www.law.cornell.edu/uscode/17/107.shtml.

If you wish to use copyrighted material from this site for purposes of your own that go beyond fair use,
you must obtain permission directly from the copyright owner.

NewLifeGames.net Web-Site is optimized for use with Fire-Fox and a minimum screen resolution of 1280x768 pixels.


Powered by SMF 1.1.20 | SMF © 2013, Simple Machines
Loon Designed by Mystica
Updated by Runic Warrior
Page created in 0.146 seconds with 21 queries.