Welcome, Guest. Please login or register.
April 28, 2024, 01:02:54 PM

Login with username, password and session length
* Home Help Arcade Login Register
.
+  Forum
|-+  **Reel Slots** Gaming Machines
| |-+  IGT S and S-plus Reel Games. (Moderator: knagl)
| | |-+  S+ Error code [63] with an SP1213		 0 Members and 1 Guest are viewing this topic. « previous next »
Pages: [1] Go Down Print
Author Topic: S+ Error code [63] with an SP1213  (Read 5278 times)
stayouttadabunker
Senior Full time Member.
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 1039
Offline Offline

Gender: Male
Posts: 13447
« on: March 09, 2011, 02:53:49 PM »
How about this?  rotflmao
After all these years, this is the FIRST time I ever got this error code [63].  Thank You!

Anyways, in the PSR for the SP1213 chip, it states that
the error code [63] is : "Card cage and Main Door Open"   bust gut laughing

wow! I didn't know that I'd run into this!
Anyways, now I gotta find the pins on the motherboard and
bypass the bloody card cage switch because I KNOW my optics are fine.
It's kinda of hard to do when there's no actual "switch" installed in the machine.... Cry Laughing

Attached below is a terrible photo I took with a "keyfob spy cam"...lol
You can't even tell if you're taking level photos with the tiny thing. Arghh!
But it will show the error >>>

* S+ Error Code [63].jpg (46.13 KB, 1057x594 - viewed 375 times.)
Logged
stayouttadabunker
Senior Full time Member.
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 1039
Offline Offline

Gender: Male
Posts: 13447
« Reply #1 on: March 09, 2011, 04:08:15 PM »
Okay,
I've researched the S+ manual and found that the J2 header on the motherboard is as follows:

Pin#1  24Vac Hot
Pin#2  24Vac Return
Pin#3  B GND
Pin#4  B GND
Pin#5  Card Cage Detect
Pin#6  Card Cage LED

Do I jump across Pins #4 and #5 on the J2 header?  Scratch Head 3

* S+ Motherboard J2 Header Pinouts.png (4.42 KB, 236x197 - viewed 806 times.)
« Last Edit: March 09, 2011, 04:22:59 PM by stayouttadabunker » Logged
Jim
MIDWEST SLOTS
Contributing Gold NLG Member
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 288
Offline Offline

Gender: Male
Posts: 1172


513-984-2201
« Reply #2 on: March 09, 2011, 04:54:56 PM »
Bunker      that signal from pin 16b  goes to R6 on the motherboard then onto J-2 pin 6   don't have the schematic in front of me for the motherboard so I can't say what that means.

Jim 
Logged
MIDWEST SLOTS   Selling Quality Slot Machines since 1995.  We service and repair all types of slot machines. Mills, Jennings, Bally EM, 1000/2000 series, Proslot, 6000. IGT  M, M+ ,S,  S+, S-2000,  I-Game,  Universal,  Video Poker, Sigma.
stayouttadabunker
Senior Full time Member.
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 1039
Offline Offline

Gender: Male
Posts: 13447
« Reply #3 on: March 09, 2011, 05:00:13 PM »
Thanks Jim,
I just made a small Molex jumper and stuck it in the J2 header.
I configured the jumper as:  Pin #4 to Pin #5
and the error Code [63] went away!  

Dancing Party

Back in business!  Cheer Leader
Logged
knagl
Global NLG Site Moderator
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 642
Offline Offline

Gender: Male
Posts: 5489


Kevin
« Reply #4 on: March 09, 2011, 07:52:56 PM »
What software are you running in it that it's even looking for a card cage closure?  Duh, SP1213 like you said in the thread title and your first message.

That'd typically be reserved for the WAP games like Wheel of Fortune and Jeopardy and whatnot...  Very odd.
Logged
If you find this site helpful, please consider making a small donation to help defray the cost of hosting and bandwidth.

Please do not PM me for support or "how to" requests -- please post your request in the forum so that everyone may assist you and everyone can benefit from the answer to your question!  Thanks! Smiley
stayouttadabunker
Senior Full time Member.
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 1039
Offline Offline

Gender: Male
Posts: 13447
« Reply #5 on: March 09, 2011, 11:33:05 PM »
Wait til you check out the PSR for it! lol
It's chock load fulla stuff!  yummy

BTW

Works only with a 10MHz MPU board.
I tried it first with a 16MHz MPU and got crazy reels.... Tongue Out
Logged
futkorn
New NLG Member 1 to 100 Post
**

Total Karma Storms: 1
Offline Offline

Posts: 35
« Reply #6 on: July 06, 2012, 02:33:57 PM »
Good day for all,

this topic helped me a lot, thanks.
Logged
cmosdata
Guest
« Reply #7 on: December 30, 2012, 03:19:40 PM »
very good, thanks.
Logged
stayouttadabunker
Senior Full time Member.
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 1039
Offline Offline

Gender: Male
Posts: 13447
« Reply #8 on: December 31, 2012, 01:21:35 PM »
Hey! Thanks guys!  propeller
I'm glad an old S+ thread of mine helped ya!  yes
Logged
Pages: [1] Go Up Print 
« previous next »
Jump to:  

SimplePortal Classic 2.0.5

If you find this site helpful, Please Consider Making a small donation to help defray the cost of hosting and bandwidth.



Newlifegames.com ™    Newlifegames.net ™    Newlifegames.org ™
   New Life Games ™    NewLifeGames ™  NLG ™ We Bring new Life to old Games ™    1-888-NLG-SLOTS ™
Are all Copyright and Trademarks of New Life Games LLC 1992 - 2021


FAIR USE NOTICE:

This site contains copyrighted material the use of which has not always been specifically authorized by the copyright owner.
We make such material available in an effort to advance awareness and understanding of the issues involved.
We believe this constitutes a fair use of any such copyrighted material as provided for in section 107 of the US Copyright Law.
In accordance with Title 17 U.S.C. Section 107, the material on this site is distributed without profit to those
who have expressed a prior interest in receiving the included information for research and educational purposes.

For more information please visit: http://www.law.cornell.edu/uscode/17/107.shtml.

If you wish to use copyrighted material from this site for purposes of your own that go beyond fair use,
you must obtain permission directly from the copyright owner.

NewLifeGames.net Web-Site is optimized for use with Fire-Fox and a minimum screen resolution of 1280x768 pixels.


Powered by SMF 1.1.20 | SMF © 2013, Simple Machines
Loon Designed by Mystica
Updated by Runic Warrior
Page created in 0.104 seconds with 20 queries.