Welcome, Guest. Please login or register.
November 25, 2024, 06:17:51 AM

Login with username, password and session length
* Home Help Arcade Login Register
.
+  Forum
|-+  Progressive Controllers, Displays and Slot Toppers
| |-+  Mikohn Progressive Systems.
| | |-+  Mikohn Progressive Controllers Displays and other info 		0 Members and 7 Guests are viewing this topic. « previous next »
Pages: 1 2 3 [4] 5 6 7 ... 36 Go Down Print
Author Topic: Mikohn Progressive Controllers Displays and other info  (Read 396324 times)
Thor777
Contributing Gold NLG Member
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 415
Offline Offline

Gender: Male
Posts: 1419


Slave to my CAT's !!!
« Reply #75 on: September 16, 2008, 11:35:29 PM »
Cactusjack
NLG Document and FAQ Writer
Sr.Tech NLG Member 1000+ Post


Members Rating: 311
[Good Karma] [Bad Karma]
 Offline

Posts: 2019



 

   Re: Mikohn Progressive Controllers Displays and other info
« Reply #88 on: January 10, 2006, 07:23:26 PM »   

--------------------------------------------------------------------------------
Not sure on exact part numbers for connectors.

The 2 pin power connector is standard 0.156" Molex inline.

The Header is standard 10 pin (2X5)  IDC type header 0.100" centers (neumerous makers).

The power going to a 12 cell Mini Chameleon is +5VDC regulated while the power going to the CHAMII+ control PCB is +10.5VDC but 12VDC works just fine since it is regulated down to 5 on the CHAMII+ board.

 
Logged
My CAT is smarter than your honor student  !!!
Thor777
Contributing Gold NLG Member
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 415
Offline Offline

Gender: Male
Posts: 1419


Slave to my CAT's !!!
« Reply #76 on: September 16, 2008, 11:36:15 PM »
ninja66
Guest


   Re: Mikohn Progressive Controllers Displays and other info
« Reply #89 on: January 17, 2006, 02:44:24 PM »   

--------------------------------------------------------------------------------
Purchased a Mikohn con1 from joey_lc on E-bay.  Now where do I get the other stuff to link up my 2 S+'s
 
Logged
My CAT is smarter than your honor student  !!!
Thor777
Contributing Gold NLG Member
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 415
Offline Offline

Gender: Male
Posts: 1419


Slave to my CAT's !!!
« Reply #77 on: September 16, 2008, 11:36:54 PM »
hotslot101
Guest


   Re: Mikohn Progressive Controllers Displays and other info
« Reply #90 on: January 17, 2006, 03:17:01 PM »   

--------------------------------------------------------------------------------
All you need to do is configure the harness to connect your machines, no hardware required. Common between machines are joined together, serial return is dito and the coin in signal is pinned out from each machine accordingly.

Cheers

Ozzy
Logged
My CAT is smarter than your honor student  !!!
Thor777
Contributing Gold NLG Member
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 415
Offline Offline

Gender: Male
Posts: 1419


Slave to my CAT's !!!
« Reply #78 on: September 16, 2008, 11:37:29 PM »
Cactusjack
NLG Document and FAQ Writer
Sr.Tech NLG Member 1000+ Post


Members Rating: 311
[Good Karma] [Bad Karma]
 Offline

Posts: 2019



 

   Re: Mikohn Progressive Controllers Displays and other info
« Reply #92 on: January 18, 2006, 09:54:43 AM »   

--------------------------------------------------------------------------------
Quote from: ninja66 on January 17, 2006, 06:06:28 PM
I don't have a display yet.  I wanted to obtain an external display.
When you say "external" display are you talking one of the Large Overhead Displays (often refered to as a meter)?

If so, they come in a bunch of different arrangements.  Basically, they are classified as 1 X 2, 2 X 3, 3 X 5 etc.  This refers to the number of LARGE panels used to make up the display.  There is currently a seller on Ebay which has the individual Panels. Minimum, you would need 2 panels to make a 1 X 2.  That would be one panel high and two panels wide (1X2).  You would then also require a power supply, a Controller board and all the necessary wiring. The CON1 is not the display controller but rather the progressive data controller.  The CON1 gathers the coin data and sends this out to the IN MACHINE DISPLAYS and the OVERHEAD DISPLAYS. 

The CON2 is basically the same as the CON1 but offers more features and has a more contemporary way of linking more units.  However, according to Joey, the CON2 is not compatible with the older hardware (LED5, CHAMII, Old Sign 1X2).  And therefore, the Newer CHAMII+ only speaks CON2 and not the older CON1.

The Overhead sign parts are usually contained in a gold display box which is then part of a larger sign (Those pretty Neon and Chase Light Displays above a bank of machines).  Of course, these can be quite costly unless they are game specific and the game is no longer on Casino's floors. Of course, buying all the individual parts, you might be able to put together a Generic Overhead and then build an enclosure for it.

IF you are talking the smaller displays which are normally found in a Machine itself behind the top pay glass they are usually 2" by 15" and of course, you could also mount those in a display box.  There are two basic versions of these.  One is often refered to as an LED5 which has intergrated drivers on the controller board for the LED display.  These LED5 displays are often smaller than the standard progressive window you find in most S+ Progressive top Pay Glasses.  The other type is from the CHAMII line (Chameleon 2).  There are CHAMII (no Plus sign) which as far as I know, are link only (not stand alone).  These require data sent to them by a link controller like the CON1.  There are also CHAMII+ which can be both link and stand alone.  Stand alone meaning it can sit in an individual machine and drive an LED display and tally coins in and progressive amounts in that machine.  The CHAMII line uses 12 cell mini chameleon displays which had an add on piggy back driver board as part of thier display board.

There is also a CHAMIII which intergrates a lot of these various boards and plugs directly on the back of the 12 Cell Mini Chameleon.  These are rather new and still used by the casinos so it is unlikely you will find these on the resale market.

I am not aware of what the actual board inside an Overhead sign are called.  But there is also a board made after the CHAMII+ which is called a SUPREME controller.  It can apparently be used for both an In machine Link or stand alone as well as controlling an overhead display.

Rumor has it, the Ebay seller with the Panels also has the various other MIKOHN components.  You might want to send him an email.  He also appears to be very knowlegable on the product.

One NLG member was trying to put togther a deal including everything necessary to link 3 S+ machines.  The cost for the Equipment was in Excess of $1000 with only a generic 1X2 sign.

Good Luck on your search and keep us posted if you get one up and running.  It seems that Progressive displays is a very desirable step after someone becomes and owner of a few slot machines.

CJ
 
« Last Edit: January 19, 2006, 11:28:34 AM by Cactusjack » 
 
Logged
My CAT is smarter than your honor student  !!!
Thor777
Contributing Gold NLG Member
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 415
Offline Offline

Gender: Male
Posts: 1419


Slave to my CAT's !!!
« Reply #79 on: September 16, 2008, 11:38:07 PM »
ninja66
Guest


   Re: Mikohn Progressive Controllers Displays and other info
« Reply #93 on: January 18, 2006, 12:03:18 PM »   

--------------------------------------------------------------------------------
I don't really want a MEGA display sign, there is a picture in the auction of a sign on a golden (appears metallic) box.  Jay also has a picture of his setup in the restoration thread where he set up a display in the tracking bracket.  The big sign that says Megabucks (on top of the tron game) is in the lines of what I'd like to have, is that a 1x2?  I have a couple of glasses with the progressive windows 2x15, but If I use those, then whenever I would make a game change, I'd loose my display, that's why I want to go external.  I've written the guy in e-bay (some guy in LV that was selling the displays with the display boards I assume) to see what he says.

Thanks for the help.
 
« Last Edit: January 18, 2006, 12:05:43 PM by ninja66 » 
 
Logged
My CAT is smarter than your honor student  !!!
Thor777
Contributing Gold NLG Member
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 415
Offline Offline

Gender: Male
Posts: 1419


Slave to my CAT's !!!
« Reply #80 on: September 16, 2008, 11:38:27 PM »
Cactusjack
NLG Document and FAQ Writer
Sr.Tech NLG Member 1000+ Post


Members Rating: 311
[Good Karma] [Bad Karma]
 Offline

Posts: 2019



 

   Re: Mikohn Progressive Controllers Displays and other info
« Reply #94 on: January 18, 2006, 12:12:58 PM »   

--------------------------------------------------------------------------------
Quote from: ninja66 on January 18, 2006, 12:03:18 PM
I don't really want a MEGA display sign, there is a picture in the auction of a sign on a golden (appears metallic) box.  Jay also has a picture of his setup in the restoration thread where he set up a display in the tracking bracket.  The big sign that says Megabucks (on top of the tron game) is in the lines of what I'd like to have, is that a 1x2?  I have a couple of glasses with the progressive windows 2x15, but If I use those, then whenever I would make a game change, I'd loose my display, that's why I want to go external.

Yes, Jay's Overhead is a 1X2.  Jay and Joey's photos are of the same exact hardware. The player tracking bracket is a custom modification he did on his own - Which I have to say was a great Idea!  This way, his display stays with the cabinet and he CAN change out games without them needing to be progressive glass titles.  His player tracking units are LED5's witht the smaller displays.  Keep in mind, he also had to modify the cabinet a bit to get the PCB to fit.

What you want to do is about the simplest form of Progressive.  The CON1 can connecto up to a number of machines and then drive the data to an overhead Meter.  I have to say, Jay's is the first one I have seen come up for auction on Ebay and it still took the handy work and resources of Joey to get it all together for him.  The Guy in Vegas selling panels has already stated he does not have any "signs".

As I recall, we found a few sign sellers by doing google searches of key words like Mikohn 1X2 and such.  However, I was affraid to ask about pricing after seeing a few sites that DID list prices.

CJ
Logged
My CAT is smarter than your honor student  !!!
Thor777
Contributing Gold NLG Member
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 415
Offline Offline

Gender: Male
Posts: 1419


Slave to my CAT's !!!
« Reply #81 on: September 16, 2008, 11:38:59 PM »
ninja66
Guest


   Re: Mikohn Progressive Controllers Displays and other info
« Reply #95 on: January 18, 2006, 12:16:36 PM »   

--------------------------------------------------------------------------------
so would it be easier to obtain a 2x15 led5 and chameleon and put that in a box (as far as cost and availability is concerned)?  I"m going to google to see what I can come up with.  I'm kind of a patient guy when it comes to saving money, so if it is way out of hand, I'll just keep my eye out on e-bay for parts.
Logged
My CAT is smarter than your honor student  !!!
Thor777
Contributing Gold NLG Member
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 415
Offline Offline

Gender: Male
Posts: 1419


Slave to my CAT's !!!
« Reply #82 on: September 16, 2008, 11:39:25 PM »
Cactusjack
NLG Document and FAQ Writer
Sr.Tech NLG Member 1000+ Post


Members Rating: 311
[Good Karma] [Bad Karma]
 Offline

Posts: 2019



 

   Re: Mikohn Progressive Controllers Displays and other info
« Reply #96 on: January 18, 2006, 12:23:54 PM »   

--------------------------------------------------------------------------------
Quote from: ninja66 on January 18, 2006, 12:16:36 PM
so would it be easier to obtain a 2x15 led5 and chameleon and put that in a box (as far as cost and availability is concerned)?  I"m going to google to see what I can come up with.  I'm kind of a patient guy when it comes to saving money, so if it is way out of hand, I'll just keep my eye out on e-bay for parts.

Yes, that would be a realistic route to take since you already own a CON1 now.  However, I think the 2"X15" display is actually rather rare for an LED5 setup.

Thanks to Joey, I have a number of CHAM2 boards I am going through for him.  However, I don't think we have any spare LED displays to go with them.  I also have some LED5 boards I am working on for Jay but again, we have no spare LEDs to go with them.

There was an ebay seller a while back that was selling the LED5 units.  He claimed to have 8 at the time.  But a few other NLGers have since purchased from him.  Hopefully, one of them can post some contact info if they want to "give up their source".  These were the smaller LEDs.

CJ
Logged
My CAT is smarter than your honor student  !!!
Thor777
Contributing Gold NLG Member
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 415
Offline Offline

Gender: Male
Posts: 1419


Slave to my CAT's !!!
« Reply #83 on: September 16, 2008, 11:39:52 PM »
ninja66
Guest


   Re: Mikohn Progressive Controllers Displays and other info
« Reply #97 on: January 18, 2006, 12:42:13 PM »   

--------------------------------------------------------------------------------
Just so I get my terminology correct, are the led5's the chameleons with the link chip or am I totally off.  From your post I gather that what you don't have is the physical LED board with the display driver on the back?

Also I thought that the 2x15 displays were used commonly with the chameleons for in-machine displays
Logged
My CAT is smarter than your honor student  !!!
Thor777
Contributing Gold NLG Member
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 415
Offline Offline

Gender: Male
Posts: 1419


Slave to my CAT's !!!
« Reply #84 on: September 16, 2008, 11:40:24 PM »
Cactusjack
NLG Document and FAQ Writer
Sr.Tech NLG Member 1000+ Post


Members Rating: 311
[Good Karma] [Bad Karma]
 Offline

Posts: 2019



 

   Re: Mikohn Progressive Controllers Displays and other info
« Reply #98 on: January 18, 2006, 01:27:01 PM »   

--------------------------------------------------------------------------------
Quote from: ninja66 on January 18, 2006, 12:42:13 PM
Just so I get my terminology correct, are the led5's the chameleons with the link chip or am I totally off.  From your post I gather that what you don't have is the physical LED board with the display driver on the back?

Also I thought that the 2x15 displays were used commonly with the chameleons for in-machine displays?

It is difficult to get the terminology correct as sometimes these things are called something different than what is actually screened or printed on the PCBs.  The Chameleon name is what Mikohn calls their Tri Color LED dot Displays.  They also make some displays I think they called Proton which are only really LARGE LED digits and can display the numbers only (no dots).  I am guessing these are the much older overhead stuff.

The LED5 board uses a special LED board since some of the drivers are on the actual controller board (no piggy back board).  It is connected with a 20 pin ribbon cable, no power harness.  As far as WE know, the LED5 board can only be used in a link system.

The 2"X15" LED board is silk screened as a "CHAM2 12 CELL Mini" and can be driven by both a CHAMII and a CHAMII+ (has piggy back driver PCB).  IT is connected with a 10 pin ribbon cable and uses a 2 pin power connector to feed +5 to the display electronics. This same Display can be driven with a CHAMIII (3) in place of the piggy back driver board.  The CHAMIII does not use a ribbon cable since it is plugged directly onto the display PCB.  As far as WE know, a CHAMII can only be used in a Link System.  A CHAMII+ can be used as both Link and Stand Alone.

And yes, the 2"X15" display would normally be what is found behind a progressive window.  However, I know of two different sizes of 12 cell displays which are both used with the LED5 controller board.  We don't actually know what game(s)/Platforms were designed to use the smaller display since most of the IGT and Bally Glass has a window which measures 2 inches by 15 inches.  The LED bricks on the smaller board measures 10 1/4" by 1 1/4"

I personally don't have it straight as to whether an LED5 is actually a  CHAM1.  The controller board that Joey calls an LED5 is silk screened as follows "2 inch Chameleon Slave Rev A"  It would be assumed that the first Chameleon controller board would not be refered to as a CHAM1 until the CHAM2 came along???

CJ
 
 
Logged
My CAT is smarter than your honor student  !!!
Thor777
Contributing Gold NLG Member
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 415
Offline Offline

Gender: Male
Posts: 1419


Slave to my CAT's !!!
« Reply #85 on: September 16, 2008, 11:40:53 PM »
ninja66
Guest


   Re: Mikohn Progressive Controllers Displays and other info
« Reply #99 on: January 18, 2006, 01:47:30 PM »   

--------------------------------------------------------------------------------
so In essence what I would need is a 2"x15" display LED, and CHAMII and a power supply for the CHAMII (As I already have a Con1), plus some box to put it in.   
Logged
My CAT is smarter than your honor student  !!!
Thor777
Contributing Gold NLG Member
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 415
Offline Offline

Gender: Male
Posts: 1419


Slave to my CAT's !!!
« Reply #86 on: September 16, 2008, 11:41:18 PM »
Cactusjack
NLG Document and FAQ Writer
Sr.Tech NLG Member 1000+ Post


Members Rating: 311
[Good Karma] [Bad Karma]
 Offline

Posts: 2019



 

   Re: Mikohn Progressive Controllers Displays and other info
« Reply #100 on: January 18, 2006, 01:54:59 PM »   

--------------------------------------------------------------------------------
Quote from: ninja66 on January 18, 2006, 01:47:30 PM
so In essence what I would need is a 2"x15" display LED, and CHAMII and a power supply for the CHAMII (As I already have a Con1), plus some box to put it in. 

Sounds about right to me.

 
Logged
My CAT is smarter than your honor student  !!!
Thor777
Contributing Gold NLG Member
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 415
Offline Offline

Gender: Male
Posts: 1419


Slave to my CAT's !!!
« Reply #87 on: September 16, 2008, 11:42:02 PM »
result1
Tech
New NLG Member 1 to 100 Post


Members Rating: 60
[Good Karma] [Bad Karma]
 Offline

Posts: 52


www.myslotnotes.com


   

   Re: Mikohn Progressive Controllers Displays and other info
« Reply #101 on: January 18, 2006, 04:43:20 PM »   

--------------------------------------------------------------------------------
Joey Here is what I have on the 9 pin con1/con 2 data cable (RS232 Cable)

* PSP RS232.pdf (307.12 KB - downloaded 508 times.)
Logged
My CAT is smarter than your honor student  !!!
Thor777
Contributing Gold NLG Member
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 415
Offline Offline

Gender: Male
Posts: 1419


Slave to my CAT's !!!
« Reply #88 on: September 16, 2008, 11:42:40 PM »
Jay
Coin-Op Links, Info and Web Sites Moderator.
Sr.Tech NLG Member 1000+ Post


Members Rating: 396
[Good Karma] [Bad Karma]
 Offline

Posts: 4183


If you cant afford to lose, you cant afford to win


   

   Re: Mikohn Progressive Controllers Displays and other info
« Reply #102 on: January 18, 2006, 09:01:34 PM »   

--------------------------------------------------------------------------------
CJ/Ninja,

I have two large manuals and I am not sure which one it is in. I think it is the Con1 manual but it might be the Chamii+ manual.
In either case one of them they have all the switch settings for each of the boards. The LED5 unit that CJ described in the earlier post matches up switch for switch with the Cham1. 
Logged
My CAT is smarter than your honor student  !!!
Thor777
Contributing Gold NLG Member
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 415
Offline Offline

Gender: Male
Posts: 1419


Slave to my CAT's !!!
« Reply #89 on: September 16, 2008, 11:43:16 PM »
Joeylc
OverWorked Admin
Site Administrator
Sr.NLG Member 501 to 1000 Post


Members Rating: 1406
[Good Karma] [Bad Karma]
 Offline

Posts: 785


NLG Shop. 928-754-4147 1-888-NLG-SLOTS


   

   Re: Mikohn Progressive Controllers Displays and other info
« Reply #104 on: January 19, 2006, 08:48:27 AM »   

--------------------------------------------------------------------------------
Sounds like you got a dam good deal at $75.00 each I was just about to list a led5 on NLG Auctions.... but no where near that cheap... 
way to go ......   
 
 Report to moderator    Logged 

--------------------------------------------------------------------------------
Hottest day in the United States recorded August 11, 1983 at 2:21 p.m. was 132 F. - recorded in the shade at the Bullhead City Fire Department.  BUT IT A DRY HEAT

I Have gone to find myself, and if I get back before I return, keep me here! 






e-Bay ID NewLifeGames_net
 
 
ninja66
Guest


   Re: Mikohn Progressive Controllers Displays and other info
« Reply #103 on: January 19, 2006, 08:29:27 AM »   

--------------------------------------------------------------------------------
WOOT WOOT!!!  Just found 2 sets of ChamII's with 2x15 displays for $75.00 each!! on their way!!!
 
 
 
 
Logged
My CAT is smarter than your honor student  !!!
Thor777
Contributing Gold NLG Member
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 415
Offline Offline

Gender: Male
Posts: 1419


Slave to my CAT's !!!
« Reply #90 on: September 16, 2008, 11:43:59 PM »
Joeylc
OverWorked Admin
Site Administrator
Sr.NLG Member 501 to 1000 Post


Members Rating: 1406
[Good Karma] [Bad Karma]
 Offline

Posts: 785


NLG Shop. 928-754-4147 1-888-NLG-SLOTS


   

   Re: Mikohn Progressive Controllers Displays and other info
« Reply #108 on: January 19, 2006, 09:23:45 AM »   

--------------------------------------------------------------------------------
Well kind of high priced but it's shoped out by me... and 100% guaranteed to work and comes with the link software "eprom" and we offer free tech support lol this site.....   

All proceeds go to support this site you know late nights of php coding.... Pizza, Soda, Etc.

SOLD
Logged
My CAT is smarter than your honor student  !!!
Thor777
Contributing Gold NLG Member
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 415
Offline Offline

Gender: Male
Posts: 1419


Slave to my CAT's !!!
« Reply #91 on: September 16, 2008, 11:44:25 PM »
ninja66
Guest


   Re: Mikohn Progressive Controllers Displays and other info
« Reply #109 on: January 19, 2006, 09:52:00 AM »   

--------------------------------------------------------------------------------
Can the ChamII's be changed to Stand Alones by replacing the eprom?
Logged
My CAT is smarter than your honor student  !!!
Thor777
Contributing Gold NLG Member
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 415
Offline Offline

Gender: Male
Posts: 1419


Slave to my CAT's !!!
« Reply #92 on: September 16, 2008, 11:44:57 PM »
Cactusjack
NLG Document and FAQ Writer
Sr.Tech NLG Member 1000+ Post


Members Rating: 311
[Good Karma] [Bad Karma]
 Offline

Posts: 2019



 

   Re: Mikohn Progressive Controllers Displays and other info
« Reply #110 on: January 19, 2006, 11:31:58 AM »   

--------------------------------------------------------------------------------
Quote from: ninja66 on January 19, 2006, 09:52:00 AM
Can the ChamII's be changed to Stand Alones by replacing the eprom?

To the best of "our" knowledge, no a CHAMII (CH2 not plus) cannot be anything but a link driver.  Therefore, you will need a CON1 to send the progressive data to it.

And the latest information I just learned is that the CHAMII+ cannot be used with a CON1.  It will only speak CON2.  This has not been totally verified but does come from a reliable source = Joey!.

CJ
Logged
My CAT is smarter than your honor student  !!!
Thor777
Contributing Gold NLG Member
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 415
Offline Offline

Gender: Male
Posts: 1419


Slave to my CAT's !!!
« Reply #93 on: September 16, 2008, 11:45:28 PM »
ninja66
Guest


   Re: Mikohn Progressive Controllers Displays and other info
« Reply #111 on: January 19, 2006, 11:51:47 AM »   

--------------------------------------------------------------------------------
oh well.  I got the Con1 from Joey anyway, so I'll just have to use it all the time then.  So my ChamII's with the con1 plus some creative wiring and I'm all done.  What is the difference between PSP 1.0 and PSP 2.0?

 
Logged
My CAT is smarter than your honor student  !!!
Thor777
Contributing Gold NLG Member
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 415
Offline Offline

Gender: Male
Posts: 1419


Slave to my CAT's !!!
« Reply #94 on: September 16, 2008, 11:45:51 PM »
Cactusjack
NLG Document and FAQ Writer
Sr.Tech NLG Member 1000+ Post


Members Rating: 311
[Good Karma] [Bad Karma]
 Offline

Posts: 2019



 

   Re: Mikohn Progressive Controllers Displays and other info
« Reply #112 on: January 19, 2006, 12:25:35 PM »   

--------------------------------------------------------------------------------
Quote from: ninja66 on January 19, 2006, 11:51:47 AM
oh well.  I got the Con1 from Joey anyway, so I'll just have to use it all the time then.  So my ChamII's with the con1 plus some creative wiring and I'm all done.  What is the difference between PSP 1.0 and PSP 2.0?



Actually, the wiring is not all that "Creative".  As I understand it, there will be two wires to feed the data from the CON1 to all the in machine displays.

Then, there will be two wires to feed the coin in signal from EACH machine you want to contribute to the progressive amount back to the CON1.

So, if your CHAMII are all self contained (power supply, display etc) Then you will have two sets of two wires going from each machine back to the CON1.

 
Logged
My CAT is smarter than your honor student  !!!
Thor777
Contributing Gold NLG Member
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 415
Offline Offline

Gender: Male
Posts: 1419


Slave to my CAT's !!!
« Reply #95 on: September 16, 2008, 11:46:34 PM »
Joeylc
OverWorked Admin
Site Administrator
Sr.NLG Member 501 to 1000 Post


Members Rating: 1406
[Good Karma] [Bad Karma]
 Offline

Posts: 785


NLG Shop. 928-754-4147 1-888-NLG-SLOTS


   

   Re: Mikohn Progressive Controllers Displays and other info
« Reply #113 on: January 19, 2006, 04:19:10 PM »   

--------------------------------------------------------------------------------
Found this on a post at http://slot-techs.com/ forum so i kind of borrowed it for reposting here...
 

* Mikohn_Cable.jpg (96.84 KB, 800x508 - viewed 669 times.)
Logged
My CAT is smarter than your honor student  !!!
Thor777
Contributing Gold NLG Member
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 415
Offline Offline

Gender: Male
Posts: 1419


Slave to my CAT's !!!
« Reply #96 on: September 16, 2008, 11:47:14 PM »
idesign
Site Administrator
Sr.Tech NLG Member 1000+ Post


Members Rating: 581
[Good Karma] [Bad Karma]
 Offline

Posts: 2520



 

   Re: Mikohn Progressive Controllers Displays and other info
« Reply #114 on: January 19, 2006, 04:23:10 PM »   

--------------------------------------------------------------------------------
Yeah, that was posted in response to a question I had regarding the RS-232 cable connection to a CHAMII+.  I ended up just jumping pins 1 and 5 on the pc side of the CHAMII+ with a little wire wrap wire and a touch of solder.  Works like a charm now.
Logged
My CAT is smarter than your honor student  !!!
Thor777
Contributing Gold NLG Member
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 415
Offline Offline

Gender: Male
Posts: 1419


Slave to my CAT's !!!
« Reply #97 on: September 16, 2008, 11:49:16 PM »
idesign
Site Administrator
Sr.Tech NLG Member 1000+ Post


Members Rating: 581
[Good Karma] [Bad Karma]
 Offline

Posts: 2520



 

   Re: Mikohn Progressive Controllers Displays and other info
« Reply #115 on: January 19, 2006, 04:25:00 PM »   

--------------------------------------------------------------------------------
Oh, I also did the same jumper thing to the pc side of the CON1.
Logged
My CAT is smarter than your honor student  !!!
Thor777
Contributing Gold NLG Member
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 415
Offline Offline

Gender: Male
Posts: 1419


Slave to my CAT's !!!
« Reply #98 on: September 16, 2008, 11:49:58 PM »
scratchee35
Contributing Gold NLG Member.
NLG Member 101 to 500 Post


Members Rating: 39
[Good Karma] [Bad Karma]
 Offline

Posts: 144



   

   Re: Mikohn Progressive Controllers Displays and other info
« Reply #117 on: January 20, 2006, 08:22:25 AM »   

--------------------------------------------------------------------------------
Ninja66.....does your contact have any displays?  I have 4 of the LED5's, just need the displays for the award glass.....

thanks!!

Scratchee35
Logged
My CAT is smarter than your honor student  !!!
Thor777
Contributing Gold NLG Member
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 415
Offline Offline

Gender: Male
Posts: 1419


Slave to my CAT's !!!
« Reply #99 on: September 16, 2008, 11:50:57 PM »
Joeylc
OverWorked Admin
Site Administrator
Sr.NLG Member 501 to 1000 Post


Members Rating: 1406
[Good Karma] [Bad Karma]
 Offline

Posts: 785


NLG Shop. 928-754-4147 1-888-NLG-SLOTS


   

   Re: Mikohn Progressive Controllers Displays and other info
« Reply #118 on: January 20, 2006, 04:58:38 PM »   

--------------------------------------------------------------------------------
THIS IS A WORK IN PROGRESS I AM DOING FOR A FRIEND.

CHAMII+ IN- MACHINE STAND ALONE PIN OUT......

WORKING IN THE GAME END OF IT NOW.
 

* stuff 001.jpg (190.33 KB, 800x600 - viewed 823 times.)
Logged
My CAT is smarter than your honor student  !!!
Pages: 1 2 3 [4] 5 6 7 ... 36 Go Up Print 
« previous next »
Jump to:  

SimplePortal Classic 2.0.5

If you find this site helpful, Please Consider Making a small donation to help defray the cost of hosting and bandwidth.



Newlifegames.com ™    Newlifegames.net ™    Newlifegames.org ™
   New Life Games ™    NewLifeGames ™  NLG ™ We Bring new Life to old Games ™    1-888-NLG-SLOTS ™
Are all Copyright and Trademarks of New Life Games LLC 1992 - 2021


FAIR USE NOTICE:

This site contains copyrighted material the use of which has not always been specifically authorized by the copyright owner.
We make such material available in an effort to advance awareness and understanding of the issues involved.
We believe this constitutes a fair use of any such copyrighted material as provided for in section 107 of the US Copyright Law.
In accordance with Title 17 U.S.C. Section 107, the material on this site is distributed without profit to those
who have expressed a prior interest in receiving the included information for research and educational purposes.

For more information please visit: http://www.law.cornell.edu/uscode/17/107.shtml.

If you wish to use copyrighted material from this site for purposes of your own that go beyond fair use,
you must obtain permission directly from the copyright owner.

NewLifeGames.net Web-Site is optimized for use with Fire-Fox and a minimum screen resolution of 1280x768 pixels.


Powered by SMF 1.1.20 | SMF © 2013, Simple Machines
Loon Designed by Mystica
Updated by Runic Warrior
Page created in 0.105 seconds with 20 queries.