Welcome, Guest. Please login or register.
November 22, 2024, 07:16:30 PM

Login with username, password and session length
* Home Help Arcade Login Register
.
+  Forum
|-+  **Reel Slots** Gaming Machines
| |-+  IGT S2000 and Vision Games.
| | |-+  S2000 EEPROM error		 0 Members and 1 Guest are viewing this topic. « previous next »
Pages: [1] Go Down Print
Author Topic: S2000 EEPROM error  (Read 4280 times)
eddarby
Guest
« on: May 13, 2012, 09:40:05 PM »
I have a Triple Stars S2000 that has stopped working and displays "call attendant". I opened the door, alarm went off. I turned reset key and display then read "eeprom error". I am new to this slot machine thing so any help would greatly be appreciated. I have owned it for about 6 months and after changing to the correct chip (also with help from this site), has worked great until now. Thanks in advance, Ed.
Logged
cowboygames
Abbys Dad
Contributing Gold NLG Member
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 680
Offline Offline

Gender: Male
Posts: 3916


Happiness in life is a great dog
« Reply #1 on: May 13, 2012, 09:50:00 PM »
With the door open keep turning reset key till it asks you to hold reset button on the mpu for 3 seconds then and do that then close the door. If it recurs and persists you may have battery or connection issues
Logged
eddarby
Guest
« Reply #2 on: May 13, 2012, 09:59:39 PM »
Thanks, Cowboy. I tried that and yes, it does repeat "call attendant". About the battery issue, I have made sure and left the machine on at all times so as to not let the battery run down. I did turn the game off and re-seat the main board but with same results. Any other ideas?
Logged
cowboygames
Abbys Dad
Contributing Gold NLG Member
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 680
Offline Offline

Gender: Male
Posts: 3916


Happiness in life is a great dog
« Reply #3 on: May 13, 2012, 10:30:15 PM »
Was the game working and started dping this or is it a new game that's been doing it since you got it?
Logged
eddarby
Guest
« Reply #4 on: May 13, 2012, 10:35:28 PM »
It has been working fine since I received it (about 6 months ago), until earlier today when it developed this problem.
Logged
cowboygames
Abbys Dad
Contributing Gold NLG Member
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 680
Offline Offline

Gender: Male
Posts: 3916


Happiness in life is a great dog
« Reply #5 on: May 13, 2012, 11:01:40 PM »
Ok, it's seems your familiar at least with removing the mpu board which may need to be done. When you get the error and open the door and turn the rest key a few times, what does it do then?
Logged
eddarby
Guest
« Reply #6 on: May 13, 2012, 11:20:56 PM »
It turns off the alarm, reads eeprom error, then reads wait, checking memory, then goes back to call attendant.
Logged
cowboygames
Abbys Dad
Contributing Gold NLG Member
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 680
Offline Offline

Gender: Male
Posts: 3916


Happiness in life is a great dog
« Reply #7 on: May 13, 2012, 11:42:33 PM »
Do you then turn the reset key again? Keeping in mind the door should remain open through this process
Logged
eddarby
Guest
« Reply #8 on: May 14, 2012, 12:16:12 AM »
Ok, this is what it reads each time I turn the key: 1)eeprom senet control failure -0XC102   2)some critical data may be lost   3)close the main door    4)please wait - testing memor,    then,   call attendant.  Any ideas? Thanks again, for your time, Ed.
Logged
cowboygames
Abbys Dad
Contributing Gold NLG Member
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 680
Offline Offline

Gender: Male
Posts: 3916


Happiness in life is a great dog
« Reply #9 on: May 14, 2012, 12:29:26 AM »
And if you open the door and turn the reset key again it does the same exact thing all over?

If so, the first thing I would try would be to turn the machine off, remove the MPU board and check your SB, SG, Version and Ram chips to make sure they are seated tightly by giving each one a good press with your thumb. Also look at them to make sure all the legs of the chips went completely into the sockets and there are no bent legs. After that, replace the MPU in the machine and turn it on. You may have to go through the reset process again, but only once if it works
Logged
Pages: [1] Go Up Print 
« previous next »
Jump to:  

SimplePortal Classic 2.0.5

If you find this site helpful, Please Consider Making a small donation to help defray the cost of hosting and bandwidth.



Newlifegames.com ™    Newlifegames.net ™    Newlifegames.org ™
   New Life Games ™    NewLifeGames ™  NLG ™ We Bring new Life to old Games ™    1-888-NLG-SLOTS ™
Are all Copyright and Trademarks of New Life Games LLC 1992 - 2021


FAIR USE NOTICE:

This site contains copyrighted material the use of which has not always been specifically authorized by the copyright owner.
We make such material available in an effort to advance awareness and understanding of the issues involved.
We believe this constitutes a fair use of any such copyrighted material as provided for in section 107 of the US Copyright Law.
In accordance with Title 17 U.S.C. Section 107, the material on this site is distributed without profit to those
who have expressed a prior interest in receiving the included information for research and educational purposes.

For more information please visit: http://www.law.cornell.edu/uscode/17/107.shtml.

If you wish to use copyrighted material from this site for purposes of your own that go beyond fair use,
you must obtain permission directly from the copyright owner.

NewLifeGames.net Web-Site is optimized for use with Fire-Fox and a minimum screen resolution of 1280x768 pixels.


Powered by SMF 1.1.20 | SMF © 2013, Simple Machines
Loon Designed by Mystica
Updated by Runic Warrior
Page created in 0.082 seconds with 20 queries.