Welcome, Guest. Please login or register.
November 26, 2024, 04:22:24 AM

Login with username, password and session length
* Home Help Arcade Login Register
.
+  Forum
|-+  **Reel Slots** Gaming Machines
| |-+  IGT S2000 and Vision Games.
| | |-+  Coin-In Jam Error s2000 Won't Clear		 0 Members and 1 Guest are viewing this topic. « previous next »
Pages: [1] Go Down Print
Author Topic: Coin-In Jam Error s2000 Won't Clear  (Read 7022 times)
JeffZ
Guest
« on: October 17, 2012, 08:32:24 PM »
Quick question for all you pros out there...have been trying to clear a coin-in jam (machine is coinless), and there were credits that were on the machine that never got paid out due to a printer malfunction.  The printer comm error cleared, but the coin-in jam started.  The deck buttons and credits displays are dark, and I can get into the configuration menu, but cannot navigate (stays on Accounting).  Boards and connections have been checked for proper seating.  At this point, should I try to clear RAM with a clear chip, or is there something else that I should try first?  Already did the open/close routine a bunch of times too.  Reels and netplex set up fine, but then goes to that hard stop right away.
Logged
mvco
Contributing NLG Member
NLG Member 101 to 500 Post
*

Total Karma Storms: 41
Offline Offline

Gender: Male
Posts: 412
« Reply #1 on: October 17, 2012, 10:03:21 PM »
In side the main door, look for the large molex connector that would be the connector to connect the coin comparitor mechanism if one was there.  There should be a jumper wire plug plugged in to that connector.  If it is just a bare molex connector, that is your problem, and you will need to locate your jumper plug.

When this jumper is missing, a coinless S2000 will not clear from the coin error.  Just had this happen to me yesterday, so fesh in my mind.  My plug had fallen out, and I could not clear the error no matter what I did until I figured out what had happened.
Logged
JeffZ
Guest
« Reply #2 on: October 17, 2012, 10:53:27 PM »
That jumper is intact (there is no coin comparitor).  Is there a chance that the door I/O board is bad and could be causing the error?  I didn't notice any lights on that board when installed, and the displays and buttons are dark.
Logged
leapyearguy
Contributing NLG Member
NLG Member 101 to 500 Post
*

Total Karma Storms: 21
Offline Offline

Gender: Male
Posts: 226
« Reply #3 on: October 17, 2012, 11:55:23 PM »
try reseating the I O board on the door or both for that matter.
Logged
20 bucks for simple repairs, 30 if you watch, and 50 if you open your mouth.
JeffZ
Guest
« Reply #4 on: October 18, 2012, 12:01:55 AM »
Did the reseating.  Ordered a new I/O board for the door just in case.  Noticed that my candle is out when the I/O board is plugged in and powered up, but when disconnected and powered up, my candle flashes.  Starting to really suspect a faulty board.  Either way, I will have that part by next week, so I will clear it first, then swap out the boards and see...any other ideas?
Logged
CVslots
Contributing Gold NLG Member
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 432
Offline Offline

Gender: Male
Posts: 2803



WWW
« Reply #5 on: October 18, 2012, 01:49:20 AM »
Absolutely...Coin error on a coinless machine...I/O is a good bet.  yes

Roslyn
Logged

www.CentralValleySlots.com
Email: centralvalleyslots@yahoo.com
FORDSBS
Contributing NLG Member
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 363
Offline Offline

Gender: Male
Posts: 4162


PET
« Reply #6 on: October 18, 2012, 09:22:01 AM »
I had one last night that that IO was problem.
Logged
JeffZ
Guest
« Reply #7 on: October 21, 2012, 12:25:35 AM »
OK.  Swapped the door I/O board, no luck in clearing the coin in jam.  Molex jumper has been checked and is intact.  Still no coin displays or deck button lights.  All other main components have been looked over and reseated.

At this point, should I try a RAM clear (97) to see if that can reset it?  I am running out of options...  Any other suggestions?   Scratch Head

Thanks to everyone for your help!   
Logged
leapyearguy
Contributing NLG Member
NLG Member 101 to 500 Post
*

Total Karma Storms: 21
Offline Offline

Gender: Male
Posts: 226
« Reply #8 on: October 21, 2012, 01:03:54 AM »
does it try to reset when you close the door? if so, try the clear, you really have nothing to lose
Logged
20 bucks for simple repairs, 30 if you watch, and 50 if you open your mouth.
JeffZ
Guest
« Reply #9 on: October 25, 2012, 10:23:45 PM »
Turned out to being a bad 7-seg display on the door.  Swapped it out, did a 97 / 17 clear and reset, reconfigured machine type and WAMM, and I'm back in business!

Thanks to everyone for getting me pointed in the right direction!
Logged
Pages: [1] Go Up Print 
« previous next »
Jump to:  

SimplePortal Classic 2.0.5

If you find this site helpful, Please Consider Making a small donation to help defray the cost of hosting and bandwidth.



Newlifegames.com ™    Newlifegames.net ™    Newlifegames.org ™
   New Life Games ™    NewLifeGames ™  NLG ™ We Bring new Life to old Games ™    1-888-NLG-SLOTS ™
Are all Copyright and Trademarks of New Life Games LLC 1992 - 2021


FAIR USE NOTICE:

This site contains copyrighted material the use of which has not always been specifically authorized by the copyright owner.
We make such material available in an effort to advance awareness and understanding of the issues involved.
We believe this constitutes a fair use of any such copyrighted material as provided for in section 107 of the US Copyright Law.
In accordance with Title 17 U.S.C. Section 107, the material on this site is distributed without profit to those
who have expressed a prior interest in receiving the included information for research and educational purposes.

For more information please visit: http://www.law.cornell.edu/uscode/17/107.shtml.

If you wish to use copyrighted material from this site for purposes of your own that go beyond fair use,
you must obtain permission directly from the copyright owner.

NewLifeGames.net Web-Site is optimized for use with Fire-Fox and a minimum screen resolution of 1280x768 pixels.


Powered by SMF 1.1.20 | SMF © 2013, Simple Machines
Loon Designed by Mystica
Updated by Runic Warrior
Page created in 0.078 seconds with 19 queries.