IGT S2000 Triple Double Diamond

[jacker]

Bought this machine with the in tensions of him supplying the parts that were missing. Well 5 months later I'm still fighting the problems. I have since purchased: hopper, Printer, coin shoot, comparator, etc. Have use clear key and the key 17. Thought I was getting close, but as of now I have 3 (minimum) issues that I need help with. Yes my first time and my bad for trusting this guy. Problem #1 The 9 pay lines has the LED's in, but are not lit up. #2 Players keys do not light up and #3 is error " MACHINE TYPE MISMATCHED". I did replace the coin-op relieving the (Coin-in jam error) and a cable was added (Coins / Bet LED's) ....after I used the clear key. I am trying to get this slot to accept coins as well as bills. It came to me as bills only. Been told the closure MB will go away when played. I suspect I also have a sound issue also. HELP

[cowboygames]

You won't get a whole lot further till you go into the key chip menu and set the game type to upright. Once that's done your 9 line display will probably work. I assume you've already set your accounting denom? And if you haven't already, while you're in the key chip menu be sure and check that coin less mode is disabled

[jacker]

Thanks so much for a fast response. Using the change button, all I get is accounting I/o test and that's it. I have used the jackpot ket to get this far but that's it. How do I start?

[CVslots]

You will need to Key chip it again. Machine type is in menu 7.1.6 

[jacker]

Ok will try in the morning. THANK YOU

[jacker]

have proceeded to the [ 7 key chip config. Should be able to use spin button to enter menu, but nothing???

[cowboygames]

Any credits on the machine? Did the key chip register when installed? You can't adjust those settings without the key chip and it won't key with credits on the machine

[jacker]

no credits on machine. Both top two lights are amber. Is this the way the chip registers?

[cowboygames]

Yep, both amber lights then you swap your sb chip back in, turn machine on with door open and you should be able to make the necessary adjustments

[brianfink]

You might want to check your spin reels button to make shure the button is pushed all the way into the socket and also make shure the micro switch isn't loose from the assembly. Also if you push the small button on the circuit board it will give you access to all the operator menues. The jackpot key only gives you access to a couple of the menues. And also after doing a clear you should be able to set the machine type and accounting and or coin denomination without doing another key chip but that's all it will let you change without a key chip.     

[jacker]

Thanks see what I can do with this info in the morning. Right now it's 105 in my shop

[jacker]

Finally got thru, to the 7 key chip. Have machine set to upright. In trying to set the denomination, I have it stuck on $2000 in accounting, coin denotations and player. can not change it. ??

[cowboygames]

Rekey it. Your bet one credit button should advance the amount and your cash out button should lower it one step at a time or vice versa

[qbert]

You will not be able to change the accounting denomination without a clear key.
Don't forget to set the machine type again (along with all the other settings) after you clear it.
You can change any other denomination with a key chip but if you want to change the accounting denomination you will need to use your clear chip.

Rich

[jacker]

Have proceeded through the 7 key set up, but have come across 7.1.4 WAMM-IPC setup.  Asking for which one and it gives me VERSION UNKNOWN... don't know where to turn now...?

[cowboygames]

What are the options for that?

[qbert]

It must have sg362 chips
set the ipc to wamm

[jacker]

guess I don't know how to do that. I tried in 7.1.4 , but all it will do or tell me is "version unknown" Must be a different way to set this but how? Thanks

[qbert]

It has been a while since I had one with IPC
when you get to 7.1.4 if you hit the spin reels button you should be able to choose the ipc type with the cash out button or service button.
You want to choose WAMM then save with the play max credit button.
If you can't get into the 7.1.4 menu you might have to use your key chip again to be able to open that menu. What I can't remember is will the key chip do it or will you have to use the clear chip.
remember if you use the clear chip you must set denominations etc before you exit out of the key chip config section. You only get one shot or you have to go through the process again.

Rich

[qbert]

I'm pretty sure you need  just the key chip to get into the 7.1.4

[jacker]

Got into it ! Now I get reel 4 tilt (this is a 3 reel machine ) and "Primary SAS Down" Wonder if it will ever run !!

[cowboygames]

For the SAS error you need to go into menu 7 and see what your SAS setting is. Should be set to Standard. The 4th reel tilt is a whole different issue. You either have a 5 reel harness installed or a jumper plug missing in the main wire harness near the motherboard. Check the SAS settings and get back to us. It's the easiest of the 2 as we'll probably need pictures to solve the other.

Who sold you this machine and how much did he charge you? I assume because he said he'd supply parts that it was some kind of dealer, correct?

[jacker]

SAS is on enhanced.  Don't know if I can get it changed to standard. Have tried a few things with no success. What to do?
Bought from a guy in Lancaster TX. Wayne. He is a wheeler dealer. My fault for trusting him.

[cowboygames]

With your key chip you should be able to change it to standard the same way you adjust other stings in those menus. Scroll to it, hit spin reels to enter, use bet one and cashout to set it to standard then hit max bet to exit

[jacker]

Can not reset SAS enhanced to standard In 7.2.1
7.2.1.1 Validation type - Enhanced mode. Just can not change it
7.2.1.2 Validation security mode - Enabled
Another place to change it?