Welcome, Guest. Please login or register.
November 22, 2024, 03:35:08 AM

Login with username, password and session length
* Home Help Arcade Login Register
.
+  Forum
|-+  **Reel Slots** Gaming Machines
| |-+  IGT S and S-plus Reel Games. (Moderator: knagl)
| | |-+  igt trouble triple diamond not working help "please read"		 0 Members and 2 Guests are viewing this topic. « previous next »
Pages: [1] Go Down Print
Author Topic: igt trouble triple diamond not working help "please read"  (Read 6450 times)
Droider
New NLG Member 1 to 100 Post
**

Total Karma Storms: 0
Offline Offline

Posts: 25
« on: July 27, 2013, 03:21:03 AM »
 I have a cousin that has a triple diamond igt I've seen two books with it one is an s2000n the other is s type. When I turn it on top glass and belly glass lights come on and bill changer cycles but reels don't spin and number lights don't worwk. I've checked fuses, all ok. Removed computer board tested battery 3.6 volts. Re installed board nothing. Pushed test button on back of power switch, nothing. I didn't go much further but to turn reset key.
Any suggestions would greatly be appreciated.
Thank you,
Droider

* 2013-06-08 16.21.53.jpg (1549.97 KB, 2560x1920 - viewed 356 times.)

* 2013-06-08 16.20.43.jpg (1368.46 KB, 2560x1920 - viewed 380 times.)
Logged
knagl
Global NLG Site Moderator
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 642
Offline Offline

Gender: Male
Posts: 5489


Kevin
« Reply #1 on: July 27, 2013, 03:39:57 AM »
You have an IGT S+ machine.  I have moved your thread from the S2000 section to the S+ section.

In addition, please read the following thread for the likely cause of your problem and the solution to it:

http://newlifegames.net/nlg/index.php?topic=14163.0
Logged
If you find this site helpful, please consider making a small donation to help defray the cost of hosting and bandwidth.

Please do not PM me for support or "how to" requests -- please post your request in the forum so that everyone may assist you and everyone can benefit from the answer to your question!  Thanks! Smiley
Slottex
Contributing Gold NLG Member
NLG Member 101 to 500 Post
*

Total Karma Storms: 120
Offline Offline

Gender: Male
Posts: 146
« Reply #2 on: July 27, 2013, 07:46:41 AM »
Check the wire harness going from power supply to mother board.
Logged
angryninjas
Contributing NLG Member
NLG Member 101 to 500 Post
*

Total Karma Storms: 147
Offline Offline

Posts: 355
« Reply #3 on: July 27, 2013, 01:11:51 PM »
Any error codes on the front of the machine, or sequence of light flashes from the candle?
Logged
Droider
New NLG Member 1 to 100 Post
**

Total Karma Storms: 0
Offline Offline

Posts: 25
« Reply #4 on: July 27, 2013, 02:33:02 PM »
Thank you for letting me know that the machine actually is and switching me to that topic.

The candlestick doesn't light and none of the numbers on the front of the machine are on. Only the general lighting is on.

Andrew
Logged
angryninjas
Contributing NLG Member
NLG Member 101 to 500 Post
*

Total Karma Storms: 147
Offline Offline

Posts: 355
« Reply #5 on: July 27, 2013, 02:37:15 PM »
Quote from: Slottex on July 27, 2013, 07:46:41 AM
Check the wire harness going from power supply to mother board.
^  Sounds likely.  It's definitely a power issue, or more specifically, power flowing to the right places.  It wouldn't be the power supply itself, since your lights are coming on.  Do you happen to have another machine to try swapping out the motherboard just to eliminate anything there that might be the culprit?  I doubt that it is, but creates peace of mind knowing what the the problem is not.  Also double check all of your wiring connections.
Logged
CVslots
Contributing Gold NLG Member
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 432
Offline Offline

Gender: Male
Posts: 2803



WWW
« Reply #6 on: July 27, 2013, 03:02:16 PM »
No displays and no reel spin indicate no power to the MPU.

Check the white molex plug coming out of the motherboard that knagl referred you to below. 95% chance that is the issue, as it is very common!  yes


Quote from: knagl on July 27, 2013, 03:39:57 AM

In addition, please read the following thread for the likely cause of your problem and the solution to it:

http://newlifegames.net/nlg/index.php?topic=14163.0
Logged

www.CentralValleySlots.com
Email: centralvalleyslots@yahoo.com
Buzz
Senior Full time Member.
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 1158
Offline Offline

Gender: Male
Posts: 4641
« Reply #7 on: July 27, 2013, 03:17:17 PM »
Here is a picture of the dirty dog, and the way I fix them. Solder and srink tube

* 001.JPG (439.31 KB, 1280x960 - viewed 430 times.)
Logged
NLGs Motto  " IF IT AIN'T BROKE GIVE ME TIME IT WILL BE "
Droider
New NLG Member 1 to 100 Post
**

Total Karma Storms: 0
Offline Offline

Posts: 25
« Reply #8 on: July 28, 2013, 02:03:05 PM »
Hello everyone, next time I get to visit I will check the plug for the board, that sounds like the most likely problem. I wish I has another machine that I could check the board with to eliminate it from being the possible issue. I will let you know next week when I get to the machine.

Thank you for all of your help,

Andrew
Logged
knagl
Global NLG Site Moderator
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 642
Offline Offline

Gender: Male
Posts: 5489


Kevin
« Reply #9 on: July 29, 2013, 01:41:37 AM »
To be clear, the board isn't the problem -- it's just the connector.  Removing and re-inserting the connector a number of times should clean it enough that it'll work for a while.
Logged
If you find this site helpful, please consider making a small donation to help defray the cost of hosting and bandwidth.

Please do not PM me for support or "how to" requests -- please post your request in the forum so that everyone may assist you and everyone can benefit from the answer to your question!  Thanks! Smiley
IamTek7
New NLG Member 1 to 100 Post
**

Total Karma Storms: 1
Offline Offline

Gender: Male
Posts: 35
« Reply #10 on: August 08, 2013, 07:18:24 PM »
Droider, sounds similar to where I am now with mine after replacing both the MPU & Motherboard going on here http://newlifegames.net/nlg/index.php?topic=25094.0

Unfortunately for me, removing and replacing the power connector a few times did get power to my reels, but not LCD.   When I get ffurther along in mine, I'll be sure to check here and help whwere I can.
Logged
Pages: [1] Go Up Print 
« previous next »
Jump to:  

SimplePortal Classic 2.0.5

If you find this site helpful, Please Consider Making a small donation to help defray the cost of hosting and bandwidth.



Newlifegames.com ™    Newlifegames.net ™    Newlifegames.org ™
   New Life Games ™    NewLifeGames ™  NLG ™ We Bring new Life to old Games ™    1-888-NLG-SLOTS ™
Are all Copyright and Trademarks of New Life Games LLC 1992 - 2021


FAIR USE NOTICE:

This site contains copyrighted material the use of which has not always been specifically authorized by the copyright owner.
We make such material available in an effort to advance awareness and understanding of the issues involved.
We believe this constitutes a fair use of any such copyrighted material as provided for in section 107 of the US Copyright Law.
In accordance with Title 17 U.S.C. Section 107, the material on this site is distributed without profit to those
who have expressed a prior interest in receiving the included information for research and educational purposes.

For more information please visit: http://www.law.cornell.edu/uscode/17/107.shtml.

If you wish to use copyrighted material from this site for purposes of your own that go beyond fair use,
you must obtain permission directly from the copyright owner.

NewLifeGames.net Web-Site is optimized for use with Fire-Fox and a minimum screen resolution of 1280x768 pixels.


Powered by SMF 1.1.20 | SMF © 2013, Simple Machines
Loon Designed by Mystica
Updated by Runic Warrior
Page created in 0.108 seconds with 20 queries.