WTB optic board for williams 400 dot 4 sencer not 6

[paul]

Looking for coin cencer board with 4 optic on it not 6  or a complet coin mech from where coin enters and dumps in hopper for eather 4 or 6  this is for a wms 400 dot machine     thanks Paul

[rokgpsman]

The WMS 400/40X manual I have only lists 4 optic and a 6 optic boards, WMS board numbers A-18097-00 and A-18097-01. What is the number off the board you are looking for? Also, you might get more people to see your message if it was in the Classifieds area with a WTB heading.

[Neonkiss]

I do have the A-18097-01 optics

[paul]

Bob what i need is the 18097-00 if you look at the eyes on back there are only 4 of them and on the 18097-01 there are 6 for me to use the one with 6 on i will need the whole bracket from coin entry down      Paul

[Neonkiss]

Bob what i need is the 18097-00 if you look at the eyes on back there are only 4 of them and on the 18097-01 there are 6 for me to use the one with 6 on i will need the whole bracket from coin entry down      Paul

Yup,
That's what I have.

[paul]

Bob if you have the 4 optics what do you want for all        Paul

[Neonkiss]

Bob if you have the 4 optics what do you want for all        Paul

I do have the A-18097-01 optics

No. I have the one with 6 eyes and it includes the entire bracket that mounts to the door, with the solenoid for the diverter and the optics.

on the 18097-01 there are 6 for me to use the one with 6 on i will need the whole bracket from coin entry down      Paul

[paul]

Bob what is price and how many do you have Paul

[Neonkiss]

Bob what is price and how many do you have Paul

PM me your address and I'll send you one for free. Make sure it fits for the 40X machines because I thought the 6 eye sensors were for the 550's rokgpsman posted that these will fit the 40X, but I have never tried.

The WMS 400/40X manual I have only lists 4 optic and a 6 optic boards, WMS board numbers A-18097-00 and A-18097-01. What is the number off the board you are looking for?

[rokgpsman]

PM me your address and I'll send you one for free. Make sure it fits for the 40X machines because I thought the 6 eye sensors were for the 550's rokgpsman posted that these will fit the 40X, but I have never tried.

The WMS 400/40X manual I have only lists 4 optic and a 6 optic boards, WMS board numbers A-18097-00 and A-18097-01. What is the number off the board you are looking for?

I just double-checked, the WMS 400/40X manual, on page 3-5 toward the back, lists both the quad and the hex optic boards as part of the coin diverter assembly. They don't show any asterisks or notes indicating that the hex optic board is for a special model or situation. And the coin chute that the optic boards mount on only shows one part listed, so I guess it works ok with either the 4 or 6 optic boards. I figured the 6 optic boards were a product improvement, like maybe for better sensing when smaller coins are used? From what the manual indicates you can use either board in a WMS 400/40X machine.

On a different page (1-5) a chart showing all the circuit boards used in the machine shows that the quad optic boards are only used on the "Upright Slot" models (which I take to mean 400/40X), whereas the hex optic boards are used on all models in production at that time (Upright Slot, Bartop Video, Upright 17" & 19" Video, Slant Top 19" Video and Slant Top).


COIN DIVERTER

1 Chute, Receiver/Diverter .... ..........................................01-13527
2 Solenoid, Diverter..........................................................A-16683
3 Spring, .398” x 1.00” (10.1 x 25.4mm)–10T Comp ..............10-473
4 Chute, Diverter....................................... .....................01-13530
5 Pin ...............................................................................02-5093
6 Bearing, 1/8" (3mm) Nyliner ..........................................20-8790-9
7 Chute, Coin Return and Opto Mounting ...........................01-001613
8 Board, Quad Opto (Coin-in Optics) ..................................A-18097-00
   Board, Hex Opto (Coin-in Optics) ....................................A-18097-01
9 Cover, Opto Board Protector...........................................03-001612
10 E-Ring, 1/8" (3mm) Shaft .............................................20-8712-12

[Neonkiss]

Thanks for the info.
I'm sending Paul two of the for free and he'll test them in his machines.
I would do that here, but all my WMS machines are wrapped up and put away for now as I have moved off that platform and on to other machines.