Welcome, Guest. Please login or register.
November 07, 2024, 01:37:31 AM

Login with username, password and session length
* Home Help Arcade Login Register
.
+  Forum
|-+  NLG Members who host their own Repair Logs of Various Games.
| |-+  Channelmaniac's Arcadecomponents' Old School Repair Logs (Moderator: channelmaniac)
| | |-+  Multicade Boards - 48 in 1, 60 in 1, Etc.
0 Members and 1 Guest are viewing this topic. « previous next »
Pages: [1] Go Down Print
Author Topic: Multicade Boards - 48 in 1, 60 in 1, Etc.  (Read 24711 times)
channelmaniac
Surface mount soldering geek
Global NLG Site Moderator
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 568
Offline Offline

Gender: Male
Posts: 2126


Few things are better than fixing an old game...


WWW
« on: September 16, 2008, 01:58:36 AM »

Model: 48-in-1
Symptom: Dead. LEDs on the board flash in sequence.

Took the plastic top off the board to troubleshoot the CPU section. If the 74LV273 ICs and the audio DAC were tapped, the screen would go from blank to garbled and the audio would pop. Reflowed the solder on those SMT chips. Board would boot but had a "data error" on Arkanoid and would reboot if the board was tapped firmly.

Reflowed the solder on the SDRAM IC to fix the reboot. Entered the game's setup menu and turned off Arkanoid. This effectively turned the game into a 47-in-1.

The code for the games is kept in a surface mount flash ROM and is not easily fixed outside the factory. Turning off Arkanoid allowed the board to boot and the other 47 games to play.
Logged

I have too many hobbies! Electronics, gunsmithing, Miatas, arcade games, metal detecting, etc...

http://www.arcadecomponents.com
channelmaniac
Surface mount soldering geek
Global NLG Site Moderator
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 568
Offline Offline

Gender: Male
Posts: 2126


Few things are better than fixing an old game...


WWW
« Reply #1 on: September 16, 2008, 01:59:23 AM »

Layout and Troubleshooting notes for 48-in-1 and 60-in-1 boards

These boards are almost identical under the plastic cover. They use different FPGA chips since the 60-in-1 also has connections (on later boards) for trackball controllers.

U31: CPU - Intel XScale LUPXA255A0C200
U49: SDRAM - 64 Megabit (8 Megabyte) - mfg varies
U19: Flash ROM - 32 Megabit (4 Megabyte) - mfg varies (Contains boot code? and game code?)
U8: EPROM - 256k x 16 bit - mfg varies - (Contains FPGA code?)

----------------

Audio:

U39: CT6630CR (48 in 1) - 16 bit audio DAC
U39: M6335G (60 in 1) - 16 bit audio DAC

These DAC chips feed a volume control and a TDA2003 audio output IC.

U39 is under the plastic cover.

----------------

Video:

U37 and U38 are 74LV273 chips. These and the surrounding resistors form the RGB video output section of the board. The resistors form an inexpensive "DAC" function on the outputs of the 273 chips.

U26 is a 74LV245 chip. This chip drives the video sync output.

Check these chips and the resistors if the video output is incorrect. They are located under the plastic cover.

----------------

If there is a corrupt game on the board it will stop booting and give an error screen. The fix is to turn off that game. Flip DIP switch 4 to get into the Setup Menu. Once there, on the first screen is the overall setup for the game. Keep moving down on the player 1 joystick to step through the games. Turn off the problematic game to skip it and its error.

----------------

These games ARE repairable as long as the CPU is OK.  The CPU is BGA mount and difficult to replace without specialized tools/training.

Spare SDRAM ICs can be found on cheap 64Mb PC-133 SDRAM DIMMs. The 74LV family of chips are 3.3v chips. Be sure to replace them with the same family of chips for proper operation.

The biggest problem I've seen on these boards is poor soldering. Reflowing the SDRAM, Flash ROM, and the video/audio SMT chips will fix a lot of intermittent problems.
Logged

I have too many hobbies! Electronics, gunsmithing, Miatas, arcade games, metal detecting, etc...

http://www.arcadecomponents.com
channelmaniac
Surface mount soldering geek
Global NLG Site Moderator
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 568
Offline Offline

Gender: Male
Posts: 2126


Few things are better than fixing an old game...


WWW
« Reply #2 on: September 16, 2008, 02:01:55 AM »

Tip: Replacing that pesky cover...

When repairing the multicade boards that have the plastic cover over the CPU section of the board do NOT use RTV silicone. When RTV cures it leaches acetic acid which is a mild corrosive. Normally this wouldn't be a big deal except that there is no ventilation under the plastic cover so any fumes leached under it have no place to escape.

Use Rubber Cement or some other type of glue to hold it in place. Try not to use something that hardens as it will be difficult to clean up if you have to repair the board again in the future.
Logged

I have too many hobbies! Electronics, gunsmithing, Miatas, arcade games, metal detecting, etc...

http://www.arcadecomponents.com
Ken Layton
Contributing NLG Member
NLG Member 101 to 500 Post
*

Total Karma Storms: 88
Offline Offline

Gender: Male
Posts: 125



« Reply #3 on: January 12, 2009, 05:32:28 PM »

Several people have reported video sync problems on these boards. Most of the time I think they have the wiring in the cabinet wrong.
Logged
channelmaniac
Surface mount soldering geek
Global NLG Site Moderator
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 568
Offline Offline

Gender: Male
Posts: 2126


Few things are better than fixing an old game...


WWW
« Reply #4 on: January 12, 2009, 11:41:31 PM »

These boards are pretty fragile. The outputs for sync are a simple 74LV245 in a VERY small SMT package. It doesn't have a huge amount of heat dissipation and isn't very hard to damage.

What makes it harder to repair is that these boards have a silly little plastic cover over that section of the board. You have to cut the melted pegs and remove the cover to work on it.

RJ
Logged

I have too many hobbies! Electronics, gunsmithing, Miatas, arcade games, metal detecting, etc...

http://www.arcadecomponents.com
channelmaniac
Surface mount soldering geek
Global NLG Site Moderator
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 568
Offline Offline

Gender: Male
Posts: 2126


Few things are better than fixing an old game...


WWW
« Reply #5 on: January 30, 2010, 05:17:51 PM »

Model 48-in-1
Symptom: Runaway controls

The board would act like all the buttons for player 1 were randomly pressed. U29, a 74LS245, handles player 1 inputs and was shorted to ground on several inputs. RP26 tied 4 inputs high and the resistor on the Player 1 Start button was open. C64 was shorted. Replaced U29, RP26, and C64. Tested game.
Logged

I have too many hobbies! Electronics, gunsmithing, Miatas, arcade games, metal detecting, etc...

http://www.arcadecomponents.com
channelmaniac
Surface mount soldering geek
Global NLG Site Moderator
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 568
Offline Offline

Gender: Male
Posts: 2126


Few things are better than fixing an old game...


WWW
« Reply #6 on: October 02, 2010, 11:49:21 PM »

Model: 60-in-1
Symptom: No sync

Replaced bad IC at U26 and tested.

This IC is a 3.3v 74LV245A and is under the plastic cover in the very center of the board.

NOTE: A 74LVT245A will work as a replacement IC.
Logged

I have too many hobbies! Electronics, gunsmithing, Miatas, arcade games, metal detecting, etc...

http://www.arcadecomponents.com
channelmaniac
Surface mount soldering geek
Global NLG Site Moderator
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 568
Offline Offline

Gender: Male
Posts: 2126


Few things are better than fixing an old game...


WWW
« Reply #7 on: August 14, 2011, 05:07:01 AM »

Model: 60-in-1
Symptom: No blue on video

Replaced 6 blown resistors in the resistor ladder on the blue output. The 8.2k ohm resistor was still good. These are all VERY tiny surface mount resistors and are in this order for each of the color outputs:

102 (1k ohm)
241 (240 ohm)
471 (470 ohm)
102 (1k ohm)
202 (2k ohm)
392 (3.9k ohm)
822 (8.2k ohm)

Use a small chisel tip iron and liquid rosin flux when placing these resistors. It takes plenty of patience and a magnifying glass of some type.
Logged

I have too many hobbies! Electronics, gunsmithing, Miatas, arcade games, metal detecting, etc...

http://www.arcadecomponents.com
channelmaniac
Surface mount soldering geek
Global NLG Site Moderator
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 568
Offline Offline

Gender: Male
Posts: 2126


Few things are better than fixing an old game...


WWW
« Reply #8 on: January 05, 2012, 03:42:50 AM »

Model: 48-in-1
Symptom: No sync

Replaced blown LV245 IC at U26. Tested.

*NOTE*: If the board is hooked up without the video ground connection then the risk of blowing this chip is much higher.
Logged

I have too many hobbies! Electronics, gunsmithing, Miatas, arcade games, metal detecting, etc...

http://www.arcadecomponents.com
channelmaniac
Surface mount soldering geek
Global NLG Site Moderator
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 568
Offline Offline

Gender: Male
Posts: 2126


Few things are better than fixing an old game...


WWW
« Reply #9 on: January 23, 2012, 12:36:35 AM »

Model: 60-in-1
Symptom: No audio

Replaced a bad TDA2003 audio amp chip and a blown 240 ohm surface mount resistor. Tested board.
Logged

I have too many hobbies! Electronics, gunsmithing, Miatas, arcade games, metal detecting, etc...

http://www.arcadecomponents.com
channelmaniac
Surface mount soldering geek
Global NLG Site Moderator
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 568
Offline Offline

Gender: Male
Posts: 2126


Few things are better than fixing an old game...


WWW
« Reply #10 on: July 15, 2012, 07:23:41 PM »

Model: 36-in-1
Symptom: Will not move down

Board had a defective, missing solder joint on pin 3 of surface mount resistor pack RP26 from the factory. Resoldered connection and tested.
Logged

I have too many hobbies! Electronics, gunsmithing, Miatas, arcade games, metal detecting, etc...

http://www.arcadecomponents.com
Pages: [1] Go Up Print 
« previous next »
Jump to:  


If you find this site helpful, Please Consider Making a small donation to help defray the cost of hosting and bandwidth.



Newlifegames.com    Newlifegames.net    Newlifegames.org
   New Life Games    NewLifeGames  NLG  We Bring new Life to old Games    1-888-NLG-SLOTS
Are all Copyright and Trademarks of New Life Games LLC 1992 - 2021


FAIR USE NOTICE:

This site contains copyrighted material the use of which has not always been specifically authorized by the copyright owner.
We make such material available in an effort to advance awareness and understanding of the issues involved.
We believe this constitutes a fair use of any such copyrighted material as provided for in section 107 of the US Copyright Law.
In accordance with Title 17 U.S.C. Section 107, the material on this site is distributed without profit to those
who have expressed a prior interest in receiving the included information for research and educational purposes.

For more information please visit: http://www.law.cornell.edu/uscode/17/107.shtml.

If you wish to use copyrighted material from this site for purposes of your own that go beyond fair use,
you must obtain permission directly from the copyright owner.

NewLifeGames.net Web-Site is optimized for use with Fire-Fox and a minimum screen resolution of 1280x768 pixels.


Powered by SMF 1.1.20 | SMF © 2013, Simple Machines
Loon Designed by Mystica
Updated by Runic Warrior
Page created in 0.086 seconds with 21 queries.