Welcome, Guest. Please login or register.
November 21, 2024, 03:00:36 PM

Login with username, password and session length
* Home Help Arcade Login Register
.
+  Forum
|-+  NLG Members who host their own Repair Logs of Various Games.
| |-+  Channelmaniac's Arcadecomponents' Old School Repair Logs (Moderator: channelmaniac)
| | |-+  Amstar Games		 0 Members and 3 Guests are viewing this topic. « previous next »
Pages: [1] Go Down Print
Author Topic: Amstar Games  (Read 6288 times)
channelmaniac
Surface mount soldering geek
Global NLG Site Moderator
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 568
Offline Offline

Gender: Male
Posts: 2126


Few things are better than fixing an old game...


WWW
« on: September 16, 2008, 02:02:48 AM »
Model: Phoenix
Symptom: No video. Whining sound from speakers

The board was stored someplace where it got wet & had what looked like leaf residue on it.

Cleaned the bottom board and replaced all 12 ROM sockets. Replaced the K1 and K2 EPROMs as they had pins that rusted off at the body.

No change. All ICs appeared dead. There was no clock signal. Replaced a bad 7404 IC to fix the clock. Game would boot but had garbage on the screen and would randomly reboot.

Replaced 1 74LS244 IC and 1 2114 SRAM ICs that had corroded legs. The rust on the 2114's legs went up the pin into the body of the IC.

Played a few games to test the system.
Logged
I have too many hobbies! Electronics, gunsmithing, Miatas, arcade games, metal detecting, etc...

http://www.arcadecomponents.com
channelmaniac
Surface mount soldering geek
Global NLG Site Moderator
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 568
Offline Offline

Gender: Male
Posts: 2126


Few things are better than fixing an old game...


WWW
« Reply #1 on: February 06, 2009, 01:17:59 AM »
Model: Phoenix
Symptom: Graphics glitch and bad audio

Replaced missing sound pot. Board was missing the shooting and explosion sounds. Replaced a bad 4006 IC at IC45. Replaced bad socket on ROM at location IC23 to fix an intermittent graphics glitch and tested board.
« Last Edit: February 07, 2009, 02:24:18 AM by channelmaniac » Logged
I have too many hobbies! Electronics, gunsmithing, Miatas, arcade games, metal detecting, etc...

http://www.arcadecomponents.com
channelmaniac
Surface mount soldering geek
Global NLG Site Moderator
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 568
Offline Offline

Gender: Male
Posts: 2126


Few things are better than fixing an old game...


WWW
« Reply #2 on: February 07, 2009, 02:24:45 AM »
Model: Phoenix
Symptom: Dead

Logic probe showed the clock signal and video sync signals were present. It also showed no activity on both the address and data busses. Replaced a bad 2114 SRAM IC to fix. Replaced broken sound pot to fix the audio output.
Logged
I have too many hobbies! Electronics, gunsmithing, Miatas, arcade games, metal detecting, etc...

http://www.arcadecomponents.com
channelmaniac
Surface mount soldering geek
Global NLG Site Moderator
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 568
Offline Offline

Gender: Male
Posts: 2126


Few things are better than fixing an old game...


WWW
« Reply #3 on: February 07, 2009, 02:26:12 AM »
Model: Phoenix
Symptom: Dead. Missing 3 chips and 17 capacitors. Has 2 pulled traces.

Obvious trace damage on board - 2 traces were sticking up from the board and there were 2 missing pads on IC17. IC17 was also missing. The CPU socket was partially melted from a soldering iron.

Replaced missing IC17. Patched 2 broken traces. Replaced bad CPU socket and replaced the missing 8085 CPU. Replaced broken IC48 on the video board.

Replaced 17 missing capacitors and 1 incorrect resistor to fix the sound subsystem.
Logged
I have too many hobbies! Electronics, gunsmithing, Miatas, arcade games, metal detecting, etc...

http://www.arcadecomponents.com
channelmaniac
Surface mount soldering geek
Global NLG Site Moderator
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 568
Offline Offline

Gender: Male
Posts: 2126


Few things are better than fixing an old game...


WWW
« Reply #4 on: February 07, 2009, 02:27:08 AM »
Model: Phoenix
Symptom: Board sync output is bad

Board had some kind of output on the sync pin but it was incorrect. Found that the board was modified. 1 trace was cut and 2 were jumpered. Reset the board back to factory, replaced the broken sound pot, and tested.
Logged
I have too many hobbies! Electronics, gunsmithing, Miatas, arcade games, metal detecting, etc...

http://www.arcadecomponents.com
Pages: [1] Go Up Print 
« previous next »
Jump to:  

SimplePortal Classic 2.0.5

If you find this site helpful, Please Consider Making a small donation to help defray the cost of hosting and bandwidth.



Newlifegames.com ™    Newlifegames.net ™    Newlifegames.org ™
   New Life Games ™    NewLifeGames ™  NLG ™ We Bring new Life to old Games ™    1-888-NLG-SLOTS ™
Are all Copyright and Trademarks of New Life Games LLC 1992 - 2021


FAIR USE NOTICE:

This site contains copyrighted material the use of which has not always been specifically authorized by the copyright owner.
We make such material available in an effort to advance awareness and understanding of the issues involved.
We believe this constitutes a fair use of any such copyrighted material as provided for in section 107 of the US Copyright Law.
In accordance with Title 17 U.S.C. Section 107, the material on this site is distributed without profit to those
who have expressed a prior interest in receiving the included information for research and educational purposes.

For more information please visit: http://www.law.cornell.edu/uscode/17/107.shtml.

If you wish to use copyrighted material from this site for purposes of your own that go beyond fair use,
you must obtain permission directly from the copyright owner.

NewLifeGames.net Web-Site is optimized for use with Fire-Fox and a minimum screen resolution of 1280x768 pixels.


Powered by SMF 1.1.20 | SMF © 2013, Simple Machines
Loon Designed by Mystica
Updated by Runic Warrior
Page created in 0.07 seconds with 20 queries.