Welcome, Guest. Please login or register.
October 14, 2024, 11:16:44 PM

Login with username, password and session length
* Home Help Arcade Login Register
.
+  Forum
|-+  NLG Members who host their own Repair Logs of Various Games.
| |-+  Channelmaniac's Arcadecomponents' Old School Repair Logs (Moderator: channelmaniac)
| | |-+  Sega Games (Other Arcade)
0 Members and 4 Guests are viewing this topic. « previous next »
Pages: 1 [2] Go Down Print
Author Topic: Sega Games (Other Arcade)  (Read 48474 times)
channelmaniac
Surface mount soldering geek
Global NLG Site Moderator
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 568
Offline Offline

Gender: Male
Posts: 2126


Few things are better than fixing an old game...


WWW
« Reply #25 on: July 06, 2012, 12:53:43 AM »

Model: Naomi
Symptom: Missing audio on right channel

Replaced burnt 510 ohm surface mount resistor at R333S and tested.
Logged

I have too many hobbies! Electronics, gunsmithing, Miatas, arcade games, metal detecting, etc...

http://www.arcadecomponents.com
channelmaniac
Surface mount soldering geek
Global NLG Site Moderator
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 568
Offline Offline

Gender: Male
Posts: 2126


Few things are better than fixing an old game...


WWW
« Reply #26 on: January 05, 2013, 08:34:22 PM »

Model: Pengo
Symptom: Dead

Board was in a bulk buy and had been scavenged for parts.

Replaced missing 74LS04 and 74LS138 ICs. Board had no clock. Replaced 74LS368 at IC6. No change. Examined clock circuitry closely and saw a hairline crack in R17. Replaced R17 and board tried to boot. Cleaned EPROM legs and board booted, but had graphics problems.

Moving graphics were jerky in nature and backgrounds and text were flipped from the direction the player sprites were playing, similar to a flipped screen in cocktail mode, until after the first round of attract mode finished then were correctly oriented. Repaired 2 gouged traces, one going to an input to a 7489 Bipolar RAM, to fix the jerking graphics. The FLIP signal coming from the 74LS259 at IC 27 was improper on power up and corrected after the first round of attract mode. Replaced the IC and tested.
Logged

I have too many hobbies! Electronics, gunsmithing, Miatas, arcade games, metal detecting, etc...

http://www.arcadecomponents.com
channelmaniac
Surface mount soldering geek
Global NLG Site Moderator
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 568
Offline Offline

Gender: Male
Posts: 2126


Few things are better than fixing an old game...


WWW
« Reply #27 on: January 13, 2013, 02:17:11 AM »

Model: Chihiro (House of the Dead III)
Symptom: Error 2: Mainboard Error

This system is a Microsoft XBox system with a Sega adapter board attached and a standard Naomi Network DIMM board and GD-ROM plugged in. The Sega adapter board had the same type of leaking .1F supercap that the Naomi 1 systems have. (Unsure on Naomi 2 as I haven't had one on the bench yet.)

Also, the Xbox system it's based off of has a 2.5v 1F supercap over on the front edge of the board. It leaks too and will corrode traces.

You MUST remove the caps, clean up the electrolyte leakage, and replace the caps. Check ANY and ALL traces around the .1F cap on the Naomi adapter board. Patch any damaged traces. Be careful as there is one trace that goes under a tiny 8 pin chip to a pin on the opposite corner and not straight up the side of that chip like it looks.

Patched 1 trace, replaced the supercaps, and tested.
Logged

I have too many hobbies! Electronics, gunsmithing, Miatas, arcade games, metal detecting, etc...

http://www.arcadecomponents.com
channelmaniac
Surface mount soldering geek
Global NLG Site Moderator
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 568
Offline Offline

Gender: Male
Posts: 2126


Few things are better than fixing an old game...


WWW
« Reply #28 on: January 14, 2013, 01:38:33 AM »

Model: Naomi GD-ROM
Symptom: Will not read discs

Controller board had a smoked IC chip. Replaced the Toshiba TC9450AF IC with one from a donor board. Tested.
Logged

I have too many hobbies! Electronics, gunsmithing, Miatas, arcade games, metal detecting, etc...

http://www.arcadecomponents.com
channelmaniac
Surface mount soldering geek
Global NLG Site Moderator
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 568
Offline Offline

Gender: Male
Posts: 2126


Few things are better than fixing an old game...


WWW
« Reply #29 on: January 14, 2013, 01:39:51 AM »

Model: Naomi GD-ROM
Symptom: Very noisy when seeking

Replaced laser head motor/gear and tested. Gear had cracked and spread far enough apart that it was causing the gears to click.
Logged

I have too many hobbies! Electronics, gunsmithing, Miatas, arcade games, metal detecting, etc...

http://www.arcadecomponents.com
channelmaniac
Surface mount soldering geek
Global NLG Site Moderator
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 568
Offline Offline

Gender: Male
Posts: 2126


Few things are better than fixing an old game...


WWW
« Reply #30 on: January 14, 2013, 01:40:42 AM »

Model: Naomi GD-ROM
Symptom: Will not read discs

Replaced laser assembly with one from a physically damaged donor drive. Tested.
Logged

I have too many hobbies! Electronics, gunsmithing, Miatas, arcade games, metal detecting, etc...

http://www.arcadecomponents.com
channelmaniac
Surface mount soldering geek
Global NLG Site Moderator
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 568
Offline Offline

Gender: Male
Posts: 2126


Few things are better than fixing an old game...


WWW
« Reply #31 on: March 03, 2013, 01:39:29 AM »

Model: Sega Naomi
Symptom: RAM Error

RAM Error: U29 bad

Removed leaking supercap, the 8 pin EEPROM, and the 42 pin BIOS and socket. Cleaned electrolyte from the board and jumpered 2 traces damaged by the leaking supercap. Replaced the 8 pin socket for the EEPROM and reinstalled the IC. Reinstalled the 42 pin socket and the BIOS chip. Reset the Backup RAM and tested.
Logged

I have too many hobbies! Electronics, gunsmithing, Miatas, arcade games, metal detecting, etc...

http://www.arcadecomponents.com
channelmaniac
Surface mount soldering geek
Global NLG Site Moderator
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 568
Offline Offline

Gender: Male
Posts: 2126


Few things are better than fixing an old game...


WWW
« Reply #32 on: March 30, 2013, 05:22:27 AM »

Model: NAOMI
Symptom: Dead

Both the GPU and case fan were seized. Replaced both fans and tested. Replaced leaking memory supercap and re-tested.

NOTE: The NAOMI will NOT boot if the GPU fan is turning slow or not at all.
Logged

I have too many hobbies! Electronics, gunsmithing, Miatas, arcade games, metal detecting, etc...

http://www.arcadecomponents.com
channelmaniac
Surface mount soldering geek
Global NLG Site Moderator
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 568
Offline Offline

Gender: Male
Posts: 2126


Few things are better than fixing an old game...


WWW
« Reply #33 on: September 01, 2013, 07:39:41 PM »

Model: Laser Ghost (System 18)
Symptom: No sync, Crackled sound

Cleaned board, cleaned edge connector with a fiberglass pencil, and replaced 2 physically damaged caps. Tested.
Logged

I have too many hobbies! Electronics, gunsmithing, Miatas, arcade games, metal detecting, etc...

http://www.arcadecomponents.com
channelmaniac
Surface mount soldering geek
Global NLG Site Moderator
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 568
Offline Offline

Gender: Male
Posts: 2126


Few things are better than fixing an old game...


WWW
« Reply #34 on: September 14, 2013, 05:40:11 PM »

Model: ST-V
Symptom: Dead

Built a replacement shorting plug to go into connector CN5. Game then booted with a cartridge error. Ran Factory Tests on Slave CPU and it passed. Disassembled the Die Hard cartridge, cleaned the edge connector, reassembled, and tested.
Logged

I have too many hobbies! Electronics, gunsmithing, Miatas, arcade games, metal detecting, etc...

http://www.arcadecomponents.com
channelmaniac
Surface mount soldering geek
Global NLG Site Moderator
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 568
Offline Offline

Gender: Male
Posts: 2126


Few things are better than fixing an old game...


WWW
« Reply #35 on: September 14, 2013, 05:40:40 PM »

Model: ST-V
Symptom: Dead

Resoldered the 2 SH-2 CPUs. Tested.
Logged

I have too many hobbies! Electronics, gunsmithing, Miatas, arcade games, metal detecting, etc...

http://www.arcadecomponents.com
channelmaniac
Surface mount soldering geek
Global NLG Site Moderator
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 568
Offline Offline

Gender: Male
Posts: 2126


Few things are better than fixing an old game...


WWW
« Reply #36 on: September 14, 2013, 05:45:27 PM »

Model: ST-V
Tip: Building a shorting connector for CN5

The board will not boot without this shorting connector or a daughterboard plugged into CN5. Take a female jack that fits the connector (Same kind as on a Playchoice-10 motherboard) and built is as follows:

Cut and remove all soldertail pins from row C
Cut and remove pins A1 through A5
Cut and remove pins B1 through B5
Cut and remove pins A27 and B27
Bend pin A6 to touch B6, A7 to touch B7, A8 to touch A8, and so on for all the remaining pins on rows A and B.
Solder pin A6 to B6, A7 to B7, A8 to B8, and so on for all the remaining pins on rows A and B.
Logged

I have too many hobbies! Electronics, gunsmithing, Miatas, arcade games, metal detecting, etc...

http://www.arcadecomponents.com
Pages: 1 [2] Go Up Print 
« previous next »
Jump to:  


If you find this site helpful, Please Consider Making a small donation to help defray the cost of hosting and bandwidth.



Newlifegames.com    Newlifegames.net    Newlifegames.org
   New Life Games    NewLifeGames  NLG  We Bring new Life to old Games    1-888-NLG-SLOTS
Are all Copyright and Trademarks of New Life Games LLC 1992 - 2021


FAIR USE NOTICE:

This site contains copyrighted material the use of which has not always been specifically authorized by the copyright owner.
We make such material available in an effort to advance awareness and understanding of the issues involved.
We believe this constitutes a fair use of any such copyrighted material as provided for in section 107 of the US Copyright Law.
In accordance with Title 17 U.S.C. Section 107, the material on this site is distributed without profit to those
who have expressed a prior interest in receiving the included information for research and educational purposes.

For more information please visit: http://www.law.cornell.edu/uscode/17/107.shtml.

If you wish to use copyrighted material from this site for purposes of your own that go beyond fair use,
you must obtain permission directly from the copyright owner.

NewLifeGames.net Web-Site is optimized for use with Fire-Fox and a minimum screen resolution of 1280x768 pixels.


Powered by SMF 1.1.20 | SMF © 2013, Simple Machines
Loon Designed by Mystica
Updated by Runic Warrior
Page created in 0.083 seconds with 20 queries.