Welcome, Guest. Please login or register.
November 21, 2024, 08:14:49 PM

Login with username, password and session length
* Home Help Arcade Login Register
.
+  Forum
|-+  **Reel Slots** Gaming Machines
| |-+  IGT S and S-plus Reel Games. (Moderator: knagl)
| | |-+  IGT S+ reels don't spin		 0 Members and 1 Guest are viewing this topic. « previous next »
Pages: [1] Go Down Print
Author Topic: IGT S+ reels don't spin  (Read 5600 times)
B-52BadByron
Contributing NLG Member
NLG Member 101 to 500 Post
*

Total Karma Storms: 12
Offline Offline

Gender: Male
Posts: 213
« on: May 24, 2010, 11:28:45 PM »
I have a couple of machines that power up, lights come on bill validator makes noise but the reels don't spin and the led lights don't come on.  The reset button and reset key have no effect.  Any ideas on where to start this trouble shoot.
Logged
coorslight115
Contributing NLG Member
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 79
Offline Offline

Gender: Male
Posts: 2602
« Reply #1 on: May 24, 2010, 11:46:51 PM »
Re-seat the MPU board a few times, make sure no bent pins, and check the connections to the mother board for burnt connectors. There is one that over heats and causes this problem a lot. It will be obvious when looking at the connector. also when powered up are the reels stiff to turn or not. I suspect not.
Logged
B-52BadByron
Contributing NLG Member
NLG Member 101 to 500 Post
*

Total Karma Storms: 12
Offline Offline

Gender: Male
Posts: 213
« Reply #2 on: May 24, 2010, 11:55:22 PM »
You are right , the reels are easy to spin even when powered up.  If I do find a burnt connector what do I do to fix the problem?

Thanks
Logged
reho33
Contributing NLG Member
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 146
Offline Offline

Gender: Male
Posts: 1594


Slot Losers of America / Tokie Owens
« Reply #3 on: May 24, 2010, 11:56:56 PM »
Stout had some posts on rewiring your own molex connectors, or you could just get it from one of the vendors above.....
Logged
** NOTE: The information contained in any of my posts relating to slot machine ownership and use is information that I have gathered from publicly known sources correspondingly under the same protections of Free Speech governed under the Laws of the United States and Canada and is for informational use only. As is my Constitutional Right under United States and Canadian Laws the redistribution of said information is considered a form of free speech. Using this information in the United States or Canada to conduct illegal gambling in states/provinces where it is unlawful has been declared against the law in those states/jurisdictions and as such I do not advocate the illegal use of such information under both the United States and Canadian Laws. All references and examples of personal experiences are hypothetical in nature, and it is up to you to determine if the information presented is applicable to your situation or not**
stayouttadabunker
Senior Full time Member.
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 1039
Offline Offline

Gender: Male
Posts: 13447
« Reply #4 on: May 25, 2010, 12:02:14 AM »
I'd remove the power supply harness going to the motherboard from the power supply box.
Spray some de-oxit into the molex receptor pins and a shot of it onto the motherboard pins.
Let dry for a few minutes and shove the molex back onto the the motherboard pins...you should be good to go!
If not, try working the molex upwards a bit and tilt it to the right...
What we're trying to establish here is - a new connection a little higher up upon the over-oxidized pins.
the display should light up and the reels should have that nice stiff feeling. yes
Logged
coorslight115
Contributing NLG Member
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 79
Offline Offline

Gender: Male
Posts: 2602
« Reply #5 on: May 25, 2010, 12:11:04 AM »
Yeah, What they said  Crazy
Logged
B-52BadByron
Contributing NLG Member
NLG Member 101 to 500 Post
*

Total Karma Storms: 12
Offline Offline

Gender: Male
Posts: 213
« Reply #6 on: May 25, 2010, 04:16:20 PM »
Power supply harness was the problem.  Replaced them with some spares that I had and works great now!  Thanks for all of the help.   applause Hail applause Hail applause Hail
Logged
stayouttadabunker
Senior Full time Member.
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 1039
Offline Offline

Gender: Male
Posts: 13447
« Reply #7 on: May 25, 2010, 06:29:50 PM »
Awessome!! I'm glad we were able to help ya!  yes
Logged
jdkmunch
Senior Full time Member.
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 624
Offline Offline

Gender: Male
Posts: 2640
« Reply #8 on: May 25, 2010, 06:47:59 PM »
 applause applause applause applause applause

Congrats!!!
Logged
Pages: [1] Go Up Print 
« previous next »
Jump to:  

SimplePortal Classic 2.0.5

If you find this site helpful, Please Consider Making a small donation to help defray the cost of hosting and bandwidth.



Newlifegames.com ™    Newlifegames.net ™    Newlifegames.org ™
   New Life Games ™    NewLifeGames ™  NLG ™ We Bring new Life to old Games ™    1-888-NLG-SLOTS ™
Are all Copyright and Trademarks of New Life Games LLC 1992 - 2021


FAIR USE NOTICE:

This site contains copyrighted material the use of which has not always been specifically authorized by the copyright owner.
We make such material available in an effort to advance awareness and understanding of the issues involved.
We believe this constitutes a fair use of any such copyrighted material as provided for in section 107 of the US Copyright Law.
In accordance with Title 17 U.S.C. Section 107, the material on this site is distributed without profit to those
who have expressed a prior interest in receiving the included information for research and educational purposes.

For more information please visit: http://www.law.cornell.edu/uscode/17/107.shtml.

If you wish to use copyrighted material from this site for purposes of your own that go beyond fair use,
you must obtain permission directly from the copyright owner.

NewLifeGames.net Web-Site is optimized for use with Fire-Fox and a minimum screen resolution of 1280x768 pixels.


Powered by SMF 1.1.20 | SMF © 2013, Simple Machines
Loon Designed by Mystica
Updated by Runic Warrior
Page created in 0.096 seconds with 19 queries.