Welcome, Guest. Please login or register.
November 23, 2024, 11:47:10 AM

Login with username, password and session length
* Home Help Arcade Login Register
.
+  Forum
|-+  **Reel Slots** Gaming Machines
| |-+  IGT S2000 and Vision Games.
| | |-+  IGT S2000 Triple stars Reel 5 Tilt error		 0 Members and 1 Guest are viewing this topic. « previous next »
Pages: [1] Go Down Print
Author Topic: IGT S2000 Triple stars Reel 5 Tilt error  (Read 5209 times)
eferry
Contributing NLG Member
New NLG Member 1 to 100 Post
*

Total Karma Storms: 10
Offline Offline

Posts: 31
« on: January 01, 2012, 04:03:02 PM »
I am having problems with my IGT Triple stars machine. after machine boots up I get Closure MB Reel 5 Tilt and call attendant. I have replaced the original CPU board. The old one would not boot up at all.  I have done a clear and key chip procedure. Machine boots up and initializes. The 5th wheel rotates about 1/2 inch and stops and rest of reels rotate properly. all wires and connectors are fine. Has anyone else had this problem?
Logged
cowboygames
Abbys Dad
Contributing Gold NLG Member
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 680
Offline Offline

Gender: Male
Posts: 3916


Happiness in life is a great dog
« Reply #1 on: January 01, 2012, 04:22:32 PM »
with the machine off, swap reel 5 with any other reel position and see if the problem follows the reel. If it stays with the #5 reel position you may have a door optics issue. If it follows the reel then you have a bad reel
Logged
Yoeddy1
The OCD kit hoarder
Contributing NLG Member
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 233
Offline Offline

Gender: Male
Posts: 3280



WWW
« Reply #2 on: January 01, 2012, 04:23:03 PM »
Put the problematic 5th reel into the 4th reel slot and the 4th reel into the 5th reel slot.  Does the problem follow the reel or does the 5th reel still exhibit the problem no matter what reel is in slot 5?

Thanks
Jason
Logged

Yoeddy's IGT Slot Machine Videos
http://www.youtube.com/user/Yoeddy1
eferry
Contributing NLG Member
New NLG Member 1 to 100 Post
*

Total Karma Storms: 10
Offline Offline

Posts: 31
« Reply #3 on: January 01, 2012, 04:26:05 PM »
I have already done that. Same condition exists. I have swapped out power supply in addition.
Logged
cowboygames
Abbys Dad
Contributing Gold NLG Member
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 680
Offline Offline

Gender: Male
Posts: 3916


Happiness in life is a great dog
« Reply #4 on: January 01, 2012, 04:32:08 PM »
I'm gonna bet on a door optis issue if you've moved reels and the issue stays with the 5th reel position. If you open and close the door do the reels try to reset?
Logged
eferry
Contributing NLG Member
New NLG Member 1 to 100 Post
*

Total Karma Storms: 10
Offline Offline

Posts: 31
« Reply #5 on: January 01, 2012, 05:08:15 PM »
yes the reels reset except 5th reel does not move. I have also changed out the door optiss.  Back in september the machine fell off the stand and the cpu board came out. I did reset all boards and connectors and machine ran fine untill now.
Logged
cowboygames
Abbys Dad
Contributing Gold NLG Member
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 680
Offline Offline

Gender: Male
Posts: 3916


Happiness in life is a great dog
« Reply #6 on: January 01, 2012, 05:24:07 PM »
Other than an issue with the motherboard I can't think of what the problem might be. If your optics are good and aligned properly which would seem to be the case as it tries to reset the reels when you close the door, your reel is good as moving the reel and the problem stayed with the position indicates, you've checked all plugs and changed the MPU. The only other thing I would look at would be the reel harness plug to the motherboard and the reel plug that the #5 reel plugs into to make sure you've got solid connections there. I think we've covered about everthing else
Logged
eferry
Contributing NLG Member
New NLG Member 1 to 100 Post
*

Total Karma Storms: 10
Offline Offline

Posts: 31
« Reply #7 on: January 24, 2012, 07:31:48 PM »
New up date on my triple stars. I have replaced the mother board and the machine now is working properly. You still have to do a clear and key chip it before booting. Thanks for your help.
Logged
stayouttadabunker
Senior Full time Member.
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 1039
Offline Offline

Gender: Male
Posts: 13447
« Reply #8 on: January 24, 2012, 07:41:30 PM »
That's good to hear eferry!
Next time, bolt the machine down to the stand!  Tongue Out
Logged
Pages: [1] Go Up Print 
« previous next »
Jump to:  

SimplePortal Classic 2.0.5

If you find this site helpful, Please Consider Making a small donation to help defray the cost of hosting and bandwidth.



Newlifegames.com ™    Newlifegames.net ™    Newlifegames.org ™
   New Life Games ™    NewLifeGames ™  NLG ™ We Bring new Life to old Games ™    1-888-NLG-SLOTS ™
Are all Copyright and Trademarks of New Life Games LLC 1992 - 2021


FAIR USE NOTICE:

This site contains copyrighted material the use of which has not always been specifically authorized by the copyright owner.
We make such material available in an effort to advance awareness and understanding of the issues involved.
We believe this constitutes a fair use of any such copyrighted material as provided for in section 107 of the US Copyright Law.
In accordance with Title 17 U.S.C. Section 107, the material on this site is distributed without profit to those
who have expressed a prior interest in receiving the included information for research and educational purposes.

For more information please visit: http://www.law.cornell.edu/uscode/17/107.shtml.

If you wish to use copyrighted material from this site for purposes of your own that go beyond fair use,
you must obtain permission directly from the copyright owner.

NewLifeGames.net Web-Site is optimized for use with Fire-Fox and a minimum screen resolution of 1280x768 pixels.


Powered by SMF 1.1.20 | SMF © 2013, Simple Machines
Loon Designed by Mystica
Updated by Runic Warrior
Page created in 0.103 seconds with 20 queries.