Welcome, Guest. Please login or register.
October 31, 2024, 11:12:17 PM

Login with username, password and session length
* Home Help Arcade Login Register
.
+  Forum
|-+  **Video Slots** Gaming machines
| |-+  IGT PE and PE Plus Poker Games.
| | |-+  Search Help for igt PE+ 1991		 0 Members and 1 Guest are viewing this topic. « previous next »
Pages: [1] Go Down Print
Author Topic: Search Help for igt PE+ 1991  (Read 13038 times)
atahualpa
Guest
« on: February 23, 2009, 03:20:14 PM »
Hi everyone,

i'm new in this site (and in the world of video poker) and hope i post at the right place.
I have an IGT joker wild that i try to repair. When i put it on, it says on the screen bad cmos call the attendant.
I think the problem is in my mainboard (Serial 7570340 Rev D), because i see a component burn, and i haven't got the diagram to know the refernece to replace it, it's a component in place Q8.
Does anyone can help me or indicate me where i can find the schematics ?
Sorry for my bad english, i'm french.

Many thanks.

Pierre.
Logged
jay
Global NLG Site Moderator
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 483
Offline Offline

Gender: Male
Posts: 3178


if you cant afford to lose you cant afford to win
« Reply #1 on: February 23, 2009, 04:01:04 PM »
Bonsoir Pierre,

Bienvenue au NLG, pardonnez mon francais.
Je suis Canadien

Le mauvais CMOS ne signifie pas nécessairement la mauvaise partie.
Il signifie que le CMOS a perdu sa memoire.

Ouvrez la porte.
Appuyez sur le bouton d'autotest blanc
Tenez le bouton pendant 3 secondes
fermez la porte
Fonctionne-t-cela ?

Snon.....
Ouvrez la porte.
Tournez la JACKPOT-RESET Clef
Appuyez sur le bouton d'autotest blanc
Tenez le bouton pendant 3 secondes
fermez la porte

regardez dedans SUBMIT-A-NEW-FILE Pour le manuel

Dos de poteau....





Logged
The only way to beat the casino is to own it
stayouttadabunker
Senior Full time Member.
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 1039
Offline Offline

Gender: Male
Posts: 13447
« Reply #2 on: February 23, 2009, 04:11:40 PM »
Transalated to english>>

Hello Pierre,
Welcome to NLG, please excuse my french
I am Canadian

The "bad CMOS" message doesnt neccessarrily mean the CMOS is bad.
All it means is  that the CMOS has lost it's memory a bit.

Open the door.
Push on the white test button
Hold it for about 3 seconds.
Close the door.
Does it work now?

If not,
Open the door.
Turn the jackpot reset key.
Push the white test button.
Hold it for about 3 seconds.
Close the door.

Take a look for the manual in the "SUBMIT-A-NEW-FILE" section

There you'll see it!


Was I close enough for our english readers? Editing is welcome...
Please excuse my french.
I am Mohawk.... Tongue Out
-mark ("marc" in french)
Logged
jay
Global NLG Site Moderator
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 483
Offline Offline

Gender: Male
Posts: 3178


if you cant afford to lose you cant afford to win
« Reply #3 on: February 23, 2009, 04:24:11 PM »
It sounds like what I intended to say..... (thankfully !) ... I don't use much French working in Alberta for an Itallian company.
In my early days I used to bounce between Geneva and Paris fairly frequently.
When you are imerssed in the language it comes a lot easier than trying to translate on the spot.
I know just enough to get myself slapped......
Logged
The only way to beat the casino is to own it
atahualpa
Guest
« Reply #4 on: February 23, 2009, 04:34:46 PM »
Hello,

many thanks for this quick answer !!!
I try the test button, and now it 's written cmos data, call the attendant.
i'll have a look tonight at the manual you upload.
I give you news soon.
Regards.

Pierre.
Logged
Buzz
Senior Full time Member.
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 1158
Offline Offline

Gender: Male
Posts: 4641
« Reply #5 on: February 23, 2009, 05:04:06 PM »
 I will try again  after pressing test button untill you hear ding close door and then turn jackpot key one time   
Logged
NLGs Motto  " IF IT AIN'T BROKE GIVE ME TIME IT WILL BE "
atahualpa
Guest
« Reply #6 on: February 24, 2009, 10:57:54 AM »
hello,

Allways the same after manipulations,
the burn component is the L201E3, it's burn and broken ; so i buy it on internet, and it will arrive in 3 days.
I'll let you know the issue when i will put it right.

thanks again.

Pierre.
Logged
atahualpa
Guest
« Reply #7 on: February 26, 2009, 05:06:32 PM »
Hi everybody,

i receive today the component and change it, so it works now !!!
Many thanks to you all.  applause
I put some photos of my machine in work.
I just have to make the bill validator works and all will be ok.
Again thanks for your help.  wave

Pierre.

* tn_100_7244.JPG (52.98 KB, 450x600 - viewed 565 times.)

* tn_100_7245.JPG (79.95 KB, 800x600 - viewed 570 times.)
Logged
stayouttadabunker
Senior Full time Member.
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 1039
Offline Offline

Gender: Male
Posts: 13447
« Reply #8 on: February 26, 2009, 05:11:22 PM »
Glad to hear you got it going!!! Congratulations! The Wave Dancing Party Dancing Party
Logged
knagl
Global NLG Site Moderator
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 642
Offline Offline

Gender: Male
Posts: 5489


Kevin
« Reply #9 on: February 26, 2009, 06:07:27 PM »
Congratulations on getting your machine up and running!

You may need a SET chip in order to enable the bill validator.  Press the white test button and page through the menus -- you should see a screen that says "Bill Validator" (or is it "Bill Acceptor"?), and then an indication as to if it's "enabled" or "disabled."

If it is disabled, you will need a SET chip to enable it.
Logged
If you find this site helpful, please consider making a small donation to help defray the cost of hosting and bandwidth.

Please do not PM me for support or "how to" requests -- please post your request in the forum so that everyone may assist you and everyone can benefit from the answer to your question!  Thanks! Smiley
atahualpa
Guest
« Reply #10 on: February 26, 2009, 06:15:12 PM »
Hello again,

thanks knaql, effectively it's writen "the bill acceptor must be enabled by the denomination setup chip" and also bill acceptor...disabled.
The reference of the acceptor are IBA4 notes acceptor, igt part N° 62539990.
Can you, please, explain me what is a set chip ?

Regards.

Pierre.
Logged
knagl
Global NLG Site Moderator
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 642
Offline Offline

Gender: Male
Posts: 5489


Kevin
« Reply #11 on: February 26, 2009, 07:43:20 PM »
A set chip, or "denomination setup chip" is a chip that you temporarially install on the MPU circuit board to enable the bill validator.  It essentially gives permission to the machine to enable the bill validator.

You can purchase a set chip from any of the vendors listed at the top of this page, or likely from any machine vendor you know of in your area.

To enable the bill validator on a PE+:

- Turn the machine off.
- Remove the MPU board
- Remove the current chip in the "Program" socket
- Install the SET chip in the Program socket (make sure to install the chip with the notch in the same direction as the chip you removed)
- Put the MPU board back in the machine and turn the power on

You should now see a screen similar to this:



(Thanks to Stolistic for the screenshot from his blog!)

Follow the directions on the screen -- use the Jackpot Reset key to set the correct denomination ($0.05, $0.25, etc.), and use the Deal/Draw button to toggle the "Disabled/Enabled" option to "Enabled."

IMPORTANT!  Make sure to press the white "self test" button to save the settings, and wait until you see "Options Saved" on the screen (like in the picture above).  Once you've done that:

- Turn the machine off
- Remove the MPU board
- Remove the SET chip from the Program socket and put your game program back in its place
- Install the MPU board again
- Turn the machine on -- your bill validator should now work
Logged
If you find this site helpful, please consider making a small donation to help defray the cost of hosting and bandwidth.

Please do not PM me for support or "how to" requests -- please post your request in the forum so that everyone may assist you and everyone can benefit from the answer to your question!  Thanks! Smiley
atahualpa
Guest
« Reply #12 on: February 26, 2009, 08:15:05 PM »
Hi,

many thanks Knagl, i'll buy one.
I see it's 3 pm in the post but for me it's 11 pm LoL, i'll go to bed.
Thanks again at everybody. it's allways good to see people so helpful and sympathic.
 Hail

Pierre.
Logged
Rep
Mr. 5 of a kind
Contributing Gold NLG Member
NLG Member 101 to 500 Post
*

Total Karma Storms: 18
Offline Offline

Gender: Male
Posts: 124
« Reply #13 on: February 26, 2009, 08:53:29 PM »
Nice in depth setup guide there knagl! Glad to see that machine up and running properly, VERY nice! I love PE+'s. Looks VERY similar to mine, I have the same belly glass Smiley What exactly does the top say? I see the big 4000 coins but can't make the rest out. Reguardless glad you're back up and running! Smiley
Logged
StatFreak
rotaredoM etiS GLN labolG
Global NLG Site Moderator
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 756
Offline Offline

Gender: Male
Posts: 8549


Warning! Spammers will be eaten, with relish!
« Reply #14 on: February 26, 2009, 11:10:00 PM »
Congratulations on getting your machine up and running.  applause applause applause  and welcome to NewLifeGames atahualpa!!!  wave wave

Good job tracing that bad component. Hail
Logged
I found myself at NLG garfield  ..but got lost again on the way home. Scratch Head 2
If found, please email me to myself. Thanks. yes
       Executive member in good standing of Rick's SMAA.                              Ehhh...What's Up Doc?
atahualpa
Guest
« Reply #15 on: February 27, 2009, 05:54:02 AM »
Hello Rep,

this is another picture of the top.

 wave

* tn_100_7247.JPG (88.45 KB, 800x600 - viewed 526 times.)
Logged
Rep
Mr. 5 of a kind
Contributing Gold NLG Member
NLG Member 101 to 500 Post
*

Total Karma Storms: 18
Offline Offline

Gender: Male
Posts: 124
« Reply #16 on: February 27, 2009, 05:03:51 PM »
Wow! Neat! Never saw a top like that on the PE+'s around this area, looks more like a Game King to me. Great pic and K+ for sharing! Very nice machine! Glad she's all up and running again for ya! Smiley
Logged
Pages: [1] Go Up Print 
« previous next »
Jump to:  

SimplePortal Classic 2.0.5

If you find this site helpful, Please Consider Making a small donation to help defray the cost of hosting and bandwidth.



Newlifegames.com ™    Newlifegames.net ™    Newlifegames.org ™
   New Life Games ™    NewLifeGames ™  NLG ™ We Bring new Life to old Games ™    1-888-NLG-SLOTS ™
Are all Copyright and Trademarks of New Life Games LLC 1992 - 2021


FAIR USE NOTICE:

This site contains copyrighted material the use of which has not always been specifically authorized by the copyright owner.
We make such material available in an effort to advance awareness and understanding of the issues involved.
We believe this constitutes a fair use of any such copyrighted material as provided for in section 107 of the US Copyright Law.
In accordance with Title 17 U.S.C. Section 107, the material on this site is distributed without profit to those
who have expressed a prior interest in receiving the included information for research and educational purposes.

For more information please visit: http://www.law.cornell.edu/uscode/17/107.shtml.

If you wish to use copyrighted material from this site for purposes of your own that go beyond fair use,
you must obtain permission directly from the copyright owner.

NewLifeGames.net Web-Site is optimized for use with Fire-Fox and a minimum screen resolution of 1280x768 pixels.


Powered by SMF 1.1.20 | SMF © 2013, Simple Machines
Loon Designed by Mystica
Updated by Runic Warrior
Page created in 0.096 seconds with 20 queries.