Welcome, Guest. Please login or register.
December 03, 2024, 03:47:25 PM

Login with username, password and session length
* Home Help Arcade Login Register
.
+  Forum
|-+  Coin Comparitors and Other Coin acceptors
| |-+  Coin Comparitors and Other Coin acceptors. (Moderator: a69mopar)
| | |-+  need help with a blown resistor on a cc16		 0 Members and 1 Guest are viewing this topic. « previous next »
Pages: [1] Go Down Print
Author Topic: need help with a blown resistor on a cc16  (Read 9405 times)
Flyinryan26
New NLG Member 1 to 100 Post
**

Total Karma Storms: 0
Offline Offline

Posts: 22
« on: February 27, 2014, 12:59:27 AM »
any help or if you can supply me one the same as this would be greatly appreciated.. 

have blown a resistor and doesnt give a value on it and the color tape has blown off...

also need a loom from the 12pin molex to the cc16 cable and to the optics in the door etc...

* cc16.JPG (22.17 KB, 720x450 - viewed 1006 times.)
Logged
tkrozleski
Contributing NLG Member
NLG Member 101 to 500 Post
*

Total Karma Storms: 23
Offline Offline

Gender: Male
Posts: 308
« Reply #1 on: February 27, 2014, 11:41:41 AM »
Is it a 24 volt AC or DC? Is it for Bally or IGT?

What position is the resistor labeled/designated on the board label? R17 ? If so R17= 75 ohm

At the top of the home page is a "NLG File System Download" tab, in there is schematics for all the comparitors
Logged
Flyinryan26
New NLG Member 1 to 100 Post
**

Total Karma Storms: 0
Offline Offline

Posts: 22
« Reply #2 on: February 27, 2014, 01:28:22 PM »
Its a cc16 24v m8.. not sure if thats the only problem I'm having coz the loom attached to it has a lot of cuts and joins in it... thanks so much for ur help been stuck on this machine for nearly a year...  :-(   n im not that great with electronics so wat does r17 mean dummys version.... thanks m8
Logged
stayouttadabunker
Senior Full time Member.
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 1039
Offline Offline

Gender: Male
Posts: 13447
« Reply #3 on: February 27, 2014, 03:52:05 PM »
That resistor is a 100k at 5%
The color bands are gold, brown, black, brown where the gold band means 5%.
Logged
Foster
The S2000 GURU
Contributing NLG Member
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 345
Offline Offline

Gender: Male
Posts: 2872
« Reply #4 on: February 27, 2014, 04:32:14 PM »
The correct way to state resistor colors is first digit, second digit, multiplier, tolerance.

a 100K ohm 5% would be brown black yellow gold
a 100   ohm 5% would be brown black brown gold
Logged
A Slot Machine and Coca-Cola Addict!!
"If it is not broke do not fix it" I keep forgetting that!
stayouttadabunker
Senior Full time Member.
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 1039
Offline Offline

Gender: Male
Posts: 13447
« Reply #5 on: February 27, 2014, 04:50:33 PM »
Quote from: Foster on February 27, 2014, 04:32:14 PM
The correct way to state resistor colors is first digit, second digit, multiplier, tolerance.

a 100K ohm 5% would be brown black yellow gold
a 100   ohm 5% would be brown black brown gold

Thanks Foster!  applause

This particular resistor is brown/black/brown/gold then.
That makes it a 100 Ohm resistor at 5%?
Logged
Foster
The S2000 GURU
Contributing NLG Member
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 345
Offline Offline

Gender: Male
Posts: 2872
« Reply #6 on: February 27, 2014, 05:14:54 PM »
Then is it is 100ohm 5%
Logged
A Slot Machine and Coca-Cola Addict!!
"If it is not broke do not fix it" I keep forgetting that!
CommTech
Contributing Gold NLG Member
Sr.NLG Member 501 to 1000 Post
*

Total Karma Storms: 251
Offline Offline

Gender: Male
Posts: 503


Joe
« Reply #7 on: February 27, 2014, 10:32:15 PM »
Quote from: Flyinryan26 on February 27, 2014, 12:59:27 AM
any help or if you can supply me one the same as this would be greatly appreciated.. 

have blown a resistor and doesnt give a value on it and the color tape has blown off...

also need a loom from the 12pin molex to the cc16 cable and to the optics in the door etc...

The bad resistor is an effect, not a cause of a problem.  If you replace just the resistor, the new one will also burn up unless you find and correct what is shorted first.   Burning Resistor
Logged
Pages: [1] Go Up Print 
« previous next »
Jump to:  

SimplePortal Classic 2.0.5

If you find this site helpful, Please Consider Making a small donation to help defray the cost of hosting and bandwidth.



Newlifegames.com ™    Newlifegames.net ™    Newlifegames.org ™
   New Life Games ™    NewLifeGames ™  NLG ™ We Bring new Life to old Games ™    1-888-NLG-SLOTS ™
Are all Copyright and Trademarks of New Life Games LLC 1992 - 2021


FAIR USE NOTICE:

This site contains copyrighted material the use of which has not always been specifically authorized by the copyright owner.
We make such material available in an effort to advance awareness and understanding of the issues involved.
We believe this constitutes a fair use of any such copyrighted material as provided for in section 107 of the US Copyright Law.
In accordance with Title 17 U.S.C. Section 107, the material on this site is distributed without profit to those
who have expressed a prior interest in receiving the included information for research and educational purposes.

For more information please visit: http://www.law.cornell.edu/uscode/17/107.shtml.

If you wish to use copyrighted material from this site for purposes of your own that go beyond fair use,
you must obtain permission directly from the copyright owner.

NewLifeGames.net Web-Site is optimized for use with Fire-Fox and a minimum screen resolution of 1280x768 pixels.


Powered by SMF 1.1.20 | SMF © 2013, Simple Machines
Loon Designed by Mystica
Updated by Runic Warrior
Page created in 0.108 seconds with 19 queries.