Welcome, Guest. Please login or register.
May 13, 2024, 09:05:28 PM

Login with username, password and session length
* Home Help Arcade Login Register
.
+  Forum
|-+  **Reel Slots** Gaming Machines
| |-+  IGT Reel Touch Games
| | |-+  Reel Touch Bill Validator Doesn't Light Up		 0 Members and 1 Guest are viewing this topic. « previous next »
Pages: 1 [2] Go Down Print
Author Topic: Reel Touch Bill Validator Doesn't Light Up  (Read 14209 times)
Buzz
Senior Full time Member.
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 1158
Offline Offline

Gender: Male
Posts: 4641
« Reply #25 on: April 24, 2011, 02:45:03 PM »
Quote from: Captain Hook on April 24, 2011, 02:04:49 PM
I decided to check the obvious things and took the board out to check the bulbs.

Both bulbs are bad.

What number are these bulbs and where can I get some????

Below are pictures of the board in question.

I checked for voltage on the wires and the Red wire has 12-13 volts on it to ground or the black wire.

So I guess I need bulbs.  Also this does not solve the issue with the digital display not working.

Thanks Much

Captain Hook


I won't say anything.     Duh! Duh! Duh!

If you decide to replace those bulbs with LEDs, your next post will be "where can I buy a BV board, I toasted mine"

You didn't have to remove the board to check the bulbs, rotate the holder CCW.  Most any auto parts store will have new ones. Make sure you get 12V.  ( I know should be 14V but 12V work just fine )
Logged
NLGs Motto  " IF IT AIN'T BROKE GIVE ME TIME IT WILL BE "
reho33
Contributing NLG Member
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 146
Offline Offline

Gender: Male
Posts: 1594


Slot Losers of America / Tokie Owens
« Reply #26 on: April 24, 2011, 04:48:01 PM »
Yea, what Buzz said.... fried mine the same way, stick with bulbs.
Logged
** NOTE: The information contained in any of my posts relating to slot machine ownership and use is information that I have gathered from publicly known sources correspondingly under the same protections of Free Speech governed under the Laws of the United States and Canada and is for informational use only. As is my Constitutional Right under United States and Canadian Laws the redistribution of said information is considered a form of free speech. Using this information in the United States or Canada to conduct illegal gambling in states/provinces where it is unlawful has been declared against the law in those states/jurisdictions and as such I do not advocate the illegal use of such information under both the United States and Canadian Laws. All references and examples of personal experiences are hypothetical in nature, and it is up to you to determine if the information presented is applicable to your situation or not**
OhioGaming
Contributing Gold NLG Member
Sr.NLG Member 501 to 1000 Post
*

Total Karma Storms: 297
Offline Offline

Posts: 834



WWW
« Reply #27 on: April 24, 2011, 08:03:32 PM »
Quote from: Captain Hook on April 24, 2011, 02:04:49 PM
I decided to check the obvious things and took the board out to check the bulbs.

Both bulbs are bad.

What number are these bulbs and where can I get some????

Below are pictures of the board in question.

I checked for voltage on the wires and the Red wire has 12-13 volts on it to ground or the black wire.

So I guess I need bulbs.  Also this does not solve the issue with the digital display not working.

Thanks Much

Captain Hook


The board pictured is not used when using a Sentry unit.
Logged
Foster
The S2000 GURU
Contributing NLG Member
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 345
Offline Offline

Gender: Male
Posts: 2872
« Reply #28 on: April 24, 2011, 08:35:26 PM »
Quote from: OhioGaming on April 24, 2011, 08:03:32 PM
Quote from: Captain Hook on April 24, 2011, 02:04:49 PM
I decided to check the obvious things and took the board out to check the bulbs.

Both bulbs are bad.

What number are these bulbs and where can I get some????

Below are pictures of the board in question.

I checked for voltage on the wires and the Red wire has 12-13 volts on it to ground or the black wire.

So I guess I need bulbs.  Also this does not solve the issue with the digital display not working.

Thanks Much

Captain Hook


The board pictured is not used when using a Sentry unit.

I have the lamp board and Sentry Installed in the S2000, It lights up the Bill Entry. the Sentry can not do that.
The bill path piece is fluorescent green and the board has cutouts at the bottom to allow the lamps or LED's to cast light into the bill entry
It looks better than the dark bill entry on the S+.
I do have LED's installed in the board.
See picture I have attached.



Is the Sentry looking like it has power?
When you first turn on the machine the Sentry will show some signs of being powered, LED's will flash, etc.

* IMAG0046.jpg (1649.72 KB, 3264x1952 - viewed 258 times.)
« Last Edit: April 24, 2011, 08:48:40 PM by Foster » Logged
A Slot Machine and Coca-Cola Addict!!
"If it is not broke do not fix it" I keep forgetting that!
OhioGaming
Contributing Gold NLG Member
Sr.NLG Member 501 to 1000 Post
*

Total Karma Storms: 297
Offline Offline

Posts: 834



WWW
« Reply #29 on: April 24, 2011, 08:52:05 PM »
Quote from: Foster on April 24, 2011, 08:35:26 PM
I have the lamp board and Sentry Installed in the S2000, It lights up the Bill Entry. the Sentry can not do that.
The bill path piece is fluorescent green and the board has cutouts at the bottom to allow the lamps or LED's to cast light into the bill entry
It looks better than the dark bill entry on the S+.
I do have LED's installed in the board.

You are correct. I wasn't thinking about the Vision or S2000. Since his has the yellow guide it would light up (with working bulbs).
Logged
Captain Hook
Contributing NLG Member
NLG Member 101 to 500 Post
*

Total Karma Storms: 26
Offline Offline

Posts: 136
« Reply #30 on: April 24, 2011, 10:02:42 PM »
Here are some pictures of the board I have.

Also here are some pictures of the wire harness that goes to it.

The little white plug goes into the display board and the other and has 2 plugs that come out behind the BV put are NOT plugged into anything.

Any idea where it goes???

* SANY2397.JPG (255.29 KB, 1280x720 - viewed 253 times.)

* SANY2398.JPG (248.63 KB, 1280x720 - viewed 238 times.)
Logged
Captain Hook
Contributing NLG Member
NLG Member 101 to 500 Post
*

Total Karma Storms: 26
Offline Offline

Posts: 136
« Reply #31 on: April 24, 2011, 10:03:45 PM »
Here's the other 2 pictures

* SANY2399.JPG (253.38 KB, 1280x720 - viewed 260 times.)

* SANY2400.JPG (252.89 KB, 1280x720 - viewed 256 times.)
Logged
Foster
The S2000 GURU
Contributing NLG Member
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 345
Offline Offline

Gender: Male
Posts: 2872
« Reply #32 on: April 24, 2011, 10:19:09 PM »
The white plug goes to the board.
Find the 5 pin going to BV, the one in your picture goes inline with the existing 5 pin connection or in series with it.

* IMAG0045.jpg (1514.84 KB, 3264x1952 - viewed 271 times.)
« Last Edit: April 24, 2011, 10:28:53 PM by Foster » Logged
A Slot Machine and Coca-Cola Addict!!
"If it is not broke do not fix it" I keep forgetting that!
Captain Hook
Contributing NLG Member
NLG Member 101 to 500 Post
*

Total Karma Storms: 26
Offline Offline

Posts: 136
« Reply #33 on: April 25, 2011, 12:47:24 AM »
Well guys I got the display to work. It was never plugged in behind the BV.

Now it lights up and displays the Denomination of the bill inserted into the machine.

Now I just need to pick up some #73 bulbs to light up the Bezel.

Thanks again for everyones help.

Captain Hook
Logged
Pages: 1 [2] Go Up Print 
« previous next »
Jump to:  

SimplePortal Classic 2.0.5

If you find this site helpful, Please Consider Making a small donation to help defray the cost of hosting and bandwidth.



Newlifegames.com ™    Newlifegames.net ™    Newlifegames.org ™
   New Life Games ™    NewLifeGames ™  NLG ™ We Bring new Life to old Games ™    1-888-NLG-SLOTS ™
Are all Copyright and Trademarks of New Life Games LLC 1992 - 2021


FAIR USE NOTICE:

This site contains copyrighted material the use of which has not always been specifically authorized by the copyright owner.
We make such material available in an effort to advance awareness and understanding of the issues involved.
We believe this constitutes a fair use of any such copyrighted material as provided for in section 107 of the US Copyright Law.
In accordance with Title 17 U.S.C. Section 107, the material on this site is distributed without profit to those
who have expressed a prior interest in receiving the included information for research and educational purposes.

For more information please visit: http://www.law.cornell.edu/uscode/17/107.shtml.

If you wish to use copyrighted material from this site for purposes of your own that go beyond fair use,
you must obtain permission directly from the copyright owner.

NewLifeGames.net Web-Site is optimized for use with Fire-Fox and a minimum screen resolution of 1280x768 pixels.


Powered by SMF 1.1.20 | SMF © 2013, Simple Machines
Loon Designed by Mystica
Updated by Runic Warrior
Page created in 0.09 seconds with 20 queries.