Welcome, Guest. Please login or register.
October 31, 2024, 11:29:13 PM

Login with username, password and session length
* Home Help Arcade Login Register
.
+  Forum
|-+  **Reel Slots** Gaming Machines
| |-+  Bally Electromechanical
| | |-+  bally 809 hopper help please		 0 Members and 2 Guests are viewing this topic. « previous next »
Pages: [1] Go Down Print
Author Topic: bally 809 hopper help please  (Read 2986 times)
junkman
NLG Member 101 to 500 Post
***

Total Karma Storms: 2
Offline Offline

Gender: Male
Posts: 220
« on: August 28, 2011, 11:55:02 PM »
I have a bally 809 that I just bought the other day. Its a nickle machine and the problem I'm having is when I hit it pays out nothing. So I swaped out the hopper from my other 809 and it pays out. So I'm getting power to the hopper. What should I look for to fix the hopper I can't test it in the machine with power on it no room and if I pull it out no power to test. What normaly goes out. Like I said it does nothing to payout. Is there a fuse ? Thanks Terry
Logged
Always remember when you leave the house keep your eye's open.
junkman
NLG Member 101 to 500 Post
***

Total Karma Storms: 2
Offline Offline

Gender: Male
Posts: 220
« Reply #1 on: September 01, 2011, 03:41:57 PM »
Got it to payout one time last night. But don't know how I done it. I turned the wheel on the side of the hoPper and put it back in the machine and align the reels for a pay out and it did but not the right amount. Got to looking at the zero switch if your look at it is it suppose to be open or close when it resets. And the wheel with the contacts on the hopper mine is plastic and the part that sets it back to zero is broke. And can anyone tell me where the contacts are sitting on the board when it returns to zero. Mine is missing the stop on the wheel. Thanks 
Logged
Always remember when you leave the house keep your eye's open.
junkman
NLG Member 101 to 500 Post
***

Total Karma Storms: 2
Offline Offline

Gender: Male
Posts: 220
« Reply #2 on: September 11, 2011, 02:04:40 PM »
The hopper is working now and pays out but pays out the wrong amount. It under pays about half of what it should. Any suggestions thanks
Logged
Always remember when you leave the house keep your eye's open.
shortrackskater
NLG Site Administrator
Sr.NLG Member 501 to 1000 Post
*

Total Karma Storms: 192
Offline Offline

Gender: Male
Posts: 845


Insert Coin
« Reply #3 on: September 20, 2011, 11:39:46 PM »
When you put in your good hopper, does it pay out correctly? If so, I'd start checking contacts on the bad hopper. Don't use any sandpaper or ANYTHING abrasive. I use just a piece of clean card stock in between contacts and gently run it through. Before doing any contact cleaning though, check the beau plug in the back of the hopper and make sure the pins are not shoved back or damaged. If they look really corroded - hold off on cleaning those with anything abrasive either since they may be silver coated. I'm having the same problem and I'm still quite new to working on EM's so I'm still waiting answers on cleaning those pins. Hope this helps for now.
Logged
Amachanic
Contributing NLG Member
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 308
Offline Offline

Gender: Male
Posts: 1392
« Reply #4 on: September 20, 2011, 11:59:49 PM »
I've cleaned those with a small wire brush wheel on my Dremel before... I've also used a 500 and 600 grit wet/dry sand paper and rubbing alcohol to clean/poliish them with good results...
Logged
If it's jammed, force it... If it breaks it needed to be replaced anyway...
Pages: [1] Go Up Print 
« previous next »
Jump to:  

SimplePortal Classic 2.0.5

If you find this site helpful, Please Consider Making a small donation to help defray the cost of hosting and bandwidth.



Newlifegames.com ™    Newlifegames.net ™    Newlifegames.org ™
   New Life Games ™    NewLifeGames ™  NLG ™ We Bring new Life to old Games ™    1-888-NLG-SLOTS ™
Are all Copyright and Trademarks of New Life Games LLC 1992 - 2021


FAIR USE NOTICE:

This site contains copyrighted material the use of which has not always been specifically authorized by the copyright owner.
We make such material available in an effort to advance awareness and understanding of the issues involved.
We believe this constitutes a fair use of any such copyrighted material as provided for in section 107 of the US Copyright Law.
In accordance with Title 17 U.S.C. Section 107, the material on this site is distributed without profit to those
who have expressed a prior interest in receiving the included information for research and educational purposes.

For more information please visit: http://www.law.cornell.edu/uscode/17/107.shtml.

If you wish to use copyrighted material from this site for purposes of your own that go beyond fair use,
you must obtain permission directly from the copyright owner.

NewLifeGames.net Web-Site is optimized for use with Fire-Fox and a minimum screen resolution of 1280x768 pixels.


Powered by SMF 1.1.20 | SMF © 2013, Simple Machines
Loon Designed by Mystica
Updated by Runic Warrior
Page created in 0.081 seconds with 20 queries.