Welcome, Guest. Please login or register.
November 23, 2024, 05:34:32 PM

Login with username, password and session length
* Home Help Arcade Login Register
.
+  Forum
|-+  **Reel Slots** Gaming Machines
| |-+  Bally Electromechanical
| | |-+  How can I free up the air cylcinder?		 0 Members and 1 Guest are viewing this topic. « previous next »
Pages: [1] Go Down Print
Author Topic: How can I free up the air cylcinder?  (Read 4780 times)
rjpohl
Contributing Gold NLG Member
Sr.NLG Member 501 to 1000 Post
*

Total Karma Storms: 103
Offline Offline

Gender: Male
Posts: 726



WWW
« on: December 12, 2010, 10:04:11 PM »
Air cylinder is stuck and I can not get it to move at all.  Any suggestions on how to free it up?
Logged

http://samronslots.com/
slotdeals
Contributing NLG Member
NLG Member 101 to 500 Post
*

Total Karma Storms: 151
Offline Offline

Gender: Male
Posts: 296


CALL 937-836-5609 FOR DETAILS


WWW
« Reply #1 on: December 12, 2010, 10:21:34 PM »
take it off the side of the mech pull the metel rod out of the casing there will be rubber melted in the casing clean it up good and lube the piston up with a grease and it will work good after that.
Logged
TERRY DAY

http://www.slotmachinesltd.com/
cowboygames
Abbys Dad
Contributing Gold NLG Member
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 680
Offline Offline

Gender: Male
Posts: 3916


Happiness in life is a great dog
« Reply #2 on: December 12, 2010, 10:22:28 PM »
Wash it down and work it with electronics parts cleaner would be my guess
Logged
Amachanic
Contributing NLG Member
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 308
Offline Offline

Gender: Male
Posts: 1392
« Reply #3 on: December 13, 2010, 12:16:59 AM »
These are a very easy fix.. Pull out the reel assembly. Remove the 4 Phillips screws holding it to the reel assembly and the pin and e-clip. Now pull out the plunger and you will see whats left of the rubber seal. Push out the pin holding the piston to the linkage, DON'T LOOSE THE SPACERS INSIDE OF THE PISTON... I have used everything from rubbing alcohol to paint thinner to clean off the melted rubber. Clean the inside of the piston cylinder, making sure the vent hole in the bottom is clear. Now reassemble with a very light coating of a light weight grease. Don't use too much grease or you will have a mess out the vent hole. Then reassemble everything and it should work as good as new...

Good luck with your project...
Logged
If it's jammed, force it... If it breaks it needed to be replaced anyway...
Jim
MIDWEST SLOTS
Contributing Gold NLG Member
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 288
Offline Offline

Gender: Male
Posts: 1172


513-984-2201
« Reply #4 on: December 13, 2010, 01:44:56 AM »
Bob,

Use finger nail polish remover. its the only thing that will cut the rubber.

aslo wear rubber latex gloves, when this goo starts coming off it will stain you hands, it will eventually come off , but gloves help a lot

clean all the parts and the the inside of the cyclinder, keep the hole clean, reassemble , and it should work fine.

the handle will fly back a little faster, nothing that can be done about this.

Jim
Logged
MIDWEST SLOTS   Selling Quality Slot Machines since 1995.  We service and repair all types of slot machines. Mills, Jennings, Bally EM, 1000/2000 series, Proslot, 6000. IGT  M, M+ ,S,  S+, S-2000,  I-Game,  Universal,  Video Poker, Sigma.
Buzz
Senior Full time Member.
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 1158
Offline Offline

Gender: Male
Posts: 4641
« Reply #5 on: December 13, 2010, 04:11:39 AM »
Jim  I'm pretty sure acetone and finger nail polish remover are the same thing. I buy it by the quart at the hardware store. Plus it's a damn good fire starter in my fireplace!!!  ( Don't use very much unless you want to loose all the hair on your arm ) been there, done that  !!!!!!!!!!!!!!
Logged
NLGs Motto  " IF IT AIN'T BROKE GIVE ME TIME IT WILL BE "
wrkey
New NLG Member 1 to 100 Post
**

Total Karma Storms: 9
Offline Offline

Posts: 56
« Reply #6 on: March 09, 2011, 06:09:45 PM »
But what about when the rubber is completely disentagrated?   Mine was... I removed it completely.. but the handle now flys back to quick and many times bounces forward enough to prevent any more coins from being added until you push the handle back.

Anyone made a replacement "flap".  Know where I can buy a replacement "flap"?

Thanks!

Rusty
Logged
wrkey
New NLG Member 1 to 100 Post
**

Total Karma Storms: 9
Offline Offline

Posts: 56
« Reply #7 on: March 09, 2011, 06:15:53 PM »
OOps.. found my answer... sorry for the multi-post.

http://newlifegames.net/nlg/index.php?topic=4987.0
Logged
Pages: [1] Go Up Print 
« previous next »
Jump to:  

SimplePortal Classic 2.0.5

If you find this site helpful, Please Consider Making a small donation to help defray the cost of hosting and bandwidth.



Newlifegames.com ™    Newlifegames.net ™    Newlifegames.org ™
   New Life Games ™    NewLifeGames ™  NLG ™ We Bring new Life to old Games ™    1-888-NLG-SLOTS ™
Are all Copyright and Trademarks of New Life Games LLC 1992 - 2021


FAIR USE NOTICE:

This site contains copyrighted material the use of which has not always been specifically authorized by the copyright owner.
We make such material available in an effort to advance awareness and understanding of the issues involved.
We believe this constitutes a fair use of any such copyrighted material as provided for in section 107 of the US Copyright Law.
In accordance with Title 17 U.S.C. Section 107, the material on this site is distributed without profit to those
who have expressed a prior interest in receiving the included information for research and educational purposes.

For more information please visit: http://www.law.cornell.edu/uscode/17/107.shtml.

If you wish to use copyrighted material from this site for purposes of your own that go beyond fair use,
you must obtain permission directly from the copyright owner.

NewLifeGames.net Web-Site is optimized for use with Fire-Fox and a minimum screen resolution of 1280x768 pixels.


Powered by SMF 1.1.20 | SMF © 2013, Simple Machines
Loon Designed by Mystica
Updated by Runic Warrior
Page created in 0.112 seconds with 20 queries.