Reel Strip Tape, 3m 465

[IFFV68]

I have a sample of 3m #465 transfer tape. Not real easy to get. They didn't want to give me a sample but changed their mind. They thought it was gold. The sample was 3/4 so I had to cut it laying on a piece of tile. I have 1/8 roll coming tomorrow.,from a different company.
I wanted to give the tape a test drive before making a purchase.
This stuff really works well. It's clear & thin.
When you use it be very careful where you put it on the reel end. You only get one try & it gets all messed up.
Very sticky but not permanent.
With my discount I don't think it costs that much. I'll know tomorrow.
 I believe someone on the site said that is what I.G.T. uses. I don't really know.
Just a thought.
I would like to thank everyone for all their help, past , present, & future,
I.F.F.V.

[stayouttadabunker]

I'd stay away from Gorilla tape though...

[IFFV68]

That sounds like good advice.
Maybe Gorilla tape is for those really big slot machines.
Big Bertha.

[stayouttadabunker]

The stuff is SO sticky that I used it to cover the bolts on my above ground pool...
7 years ago!!!

[Yoeddy1]

Staples work well. 

Jason

[poppo]

Very sticky but not permanent.

I was googling it and I kept seeing 'permanent bond' in the desciption. 

[a69mopar]

Staples work well. 

Jason

Staples?  I think you jest.

W

[edison]

I found that this works the best for me.
Edison

http://www.officedepot.com/a/products/508218/Scotch-Wallsaver-Removable-Poster-Tape-34/

[poppo]

I found that this works the best for me.

Yeah, that is pretty much the 'standard' tape most folks use. I've never really needed anything stronger.

[brichter]

+1 for the poster tape

[Yoeddy1]

Staples work well.  
Jason

Staples?  I think you jest.

W

Now Wayne, woud I do that?  My bad...I actually meant pop rivets.  

Jason

[stayouttadabunker]

Heck! For a real strong bond so the strips never come off again...
pour an entire tube of Crazy Glue or Plumber's Silicone Adhesive into the basket slits
and jam the strips in there!  

Try to get the clear liquid, real drippy glues so you can see
the symbols after you've slobbered it all over the place!

Hey! Why not kill two birds with one stone!
Make sure a little drips  down onto the reel shaft in the motor
( I've  heard this stops the noisy reels...stops the reels too!   )
If the reels actually spin  when you power up the machine - you've done a fantastic job!  

oh! I almost forgot to add that before everything dries,
make sure the jackpot symbols are on the payline.

That way afterwards - you can make pretend...









warning...do not actually try this at home...lol

[knagl]

I use Office Max double-sided tape.  I just removed some reel strips that I installed a couple of years ago in my S+, and the tape was still very sticky (but with some gentle pulling I was able to coax the strip apart without damaging it).

[IFFV68]

Tape,
I've tried the Double sided Scotch Tape. Red Label, Yellow,etc.
I have a couple sets of not so new strips & those mentioned tapes always come apart in  some places on the strip after a few spins.
If those work for others that is great. If it works why change, it's only tape.
I like a very tight seal & neat looking seams when I can get them.
The #465 transfer tape is less than a dollar a roll difference.
I only mentioned this to maybe help others who are looking for a different alternative.

[IFFV68]

Bunker,
Now I know why no one will buy reel strips from you.
That much glue may make you a little foggy.
Only kidding,
I'm sure you don't use a whole tube?

[knagl]

I only mentioned this to maybe help others who are looking for a different alternative.

No offense intended at all, IFFV, and K+ to you for posting the info as it very well may help someone.  I just was adding in the source I use for "reel strip tape" that has worked for me. 

[stayouttadabunker]

Bunker,
Now I know why no one will buy reel strips from you.
That much glue may make you a little foggy.
Only kidding,
I'm sure you don't use a whole tube?

lol...I was only joking in that post...
Blame it on Eddy!
He started it!!!    

[Yoeddy1]

By using a whole tube do you mean on the strips or that Bunker would sniff a whole tube? 

I didn't start it Bunker!  I really do use pop rivets!!  LOL!

Jason

[Foster]

IFFV68 where did you get it?

[stayouttadabunker]

Hey! I gave up glue a long time ago...
I snort paint cans now!!  

[Yoeddy1]

Hey! I gave up glue a long time ago...
I snort paint cans now!! 

At least you've moved on from spray paint and paper bags.  I'm proud of ya my friend.

Jason

[stayouttadabunker]

Hey! I gave up glue a long time ago...
I snort paint cans now!! 

At least you've moved on from spray paint and paper bags.  I'm proud of ya my friend.

Jason

Yeah...Thanks?  only problem is that I'm starting to look like your avatar!  

[Yoeddy1]

But at least you're among friends that will help you beat this.  Lol!

Jason

[StatFreak]

IFFV68 where did you get it?

I second that question.  And how much was it?

Stat


For those interested, idesign posted that this is the tape IGT uses for new strips when IFFV68 asked about eight months ago.

[PLUNGER BOY]

pour an entire tube of Crazy Glue or Plumber's Silicone Adhesive AND BREATH DEEPLY. I DIDNT INHALE
ITS JUST A JOB PERK . GROWING UP IN THE 70S BUZZZZZZZZZZZZZZZZZZZZZZZZZZZZ










...