Welcome, Guest. Please login or register.
November 24, 2024, 11:08:08 PM

Login with username, password and session length
* Home Help Arcade Login Register
.
+  Forum
|-+  **Reel Slots** Gaming Machines
| |-+  Other Reel Games
| | |-+  Jennings 400 blows 3rd fuse		 0 Members and 1 Guest are viewing this topic. « previous next »
Pages: [1] Go Down Print
Author Topic: Jennings 400 blows 3rd fuse  (Read 4383 times)
Barryt
Guest
« on: July 11, 2011, 09:15:57 PM »
I recently acquired a Jennings 400 3 pay nickel(5c) machine and it was working fine until it seems to blow the third fuse which I think is rated at 4amps (although the machne has 3 fuses in it rated at 5 amps)  When I hit the on switch after putting in a new fuse it immediately blows the new fuse.  I live remote from a ready repair facility, so I am soliciting your expertise.  Anyone have any ideas about the cause?  It seemed to have happened after my granddaughters hit a couple of big payouts while playing on the machine and there was a slight electrical odor afterwards.
Thanks if you can help a Non-EE
Barry T

* slotmachine.jpg (206.97 KB, 600x801 - viewed 321 times.)
Logged
reho33
Contributing NLG Member
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 146
Offline Offline

Gender: Male
Posts: 1594


Slot Losers of America / Tokie Owens
« Reply #1 on: July 11, 2011, 11:22:38 PM »
From the behavior you described it sounds like rust or corrosion that is creating a short somewhere. It is an Electro-Mechanical  so maybe a reel board or sensor is shorted. I will however defer to the real EM experts on here.
Logged
** NOTE: The information contained in any of my posts relating to slot machine ownership and use is information that I have gathered from publicly known sources correspondingly under the same protections of Free Speech governed under the Laws of the United States and Canada and is for informational use only. As is my Constitutional Right under United States and Canadian Laws the redistribution of said information is considered a form of free speech. Using this information in the United States or Canada to conduct illegal gambling in states/provinces where it is unlawful has been declared against the law in those states/jurisdictions and as such I do not advocate the illegal use of such information under both the United States and Canadian Laws. All references and examples of personal experiences are hypothetical in nature, and it is up to you to determine if the information presented is applicable to your situation or not**
StatFreak
rotaredoM etiS GLN labolG
Global NLG Site Moderator
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 756
Offline Offline

Gender: Male
Posts: 8549


Warning! Spammers will be eaten, with relish!
« Reply #2 on: July 12, 2011, 05:33:22 AM »
 Bump Do we have any members who know about these Jennings?

Stat garfield
Logged
I found myself at NLG garfield  ..but got lost again on the way home. Scratch Head 2
If found, please email me to myself. Thanks. yes
       Executive member in good standing of Rick's SMAA.                              Ehhh...What's Up Doc?
reho33
Contributing NLG Member
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 146
Offline Offline

Gender: Male
Posts: 1594


Slot Losers of America / Tokie Owens
« Reply #3 on: July 12, 2011, 12:40:42 PM »
I'm thinking Op-Bell??
Logged
** NOTE: The information contained in any of my posts relating to slot machine ownership and use is information that I have gathered from publicly known sources correspondingly under the same protections of Free Speech governed under the Laws of the United States and Canada and is for informational use only. As is my Constitutional Right under United States and Canadian Laws the redistribution of said information is considered a form of free speech. Using this information in the United States or Canada to conduct illegal gambling in states/provinces where it is unlawful has been declared against the law in those states/jurisdictions and as such I do not advocate the illegal use of such information under both the United States and Canadian Laws. All references and examples of personal experiences are hypothetical in nature, and it is up to you to determine if the information presented is applicable to your situation or not**
StatFreak
rotaredoM etiS GLN labolG
Global NLG Site Moderator
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 756
Offline Offline

Gender: Male
Posts: 8549


Warning! Spammers will be eaten, with relish!
« Reply #4 on: July 12, 2011, 05:50:47 PM »
He hasn't been on for over a month.

Barry, you might, however, want to send him a pm or an email.
Logged
I found myself at NLG garfield  ..but got lost again on the way home. Scratch Head 2
If found, please email me to myself. Thanks. yes
       Executive member in good standing of Rick's SMAA.                              Ehhh...What's Up Doc?
Neonkiss
Contributing Gold NLG Member
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 436
Offline Offline

Gender: Male
Posts: 2084
« Reply #5 on: July 12, 2011, 06:36:40 PM »
I would suggest pulling out the hopper and disconnecting components.
Then install a new fuse and power it back up. If the fuse doesn't blow, then start plugging things back in until it does.
At that point, the last item plugged in should be the issue.
Logged
Nothing brings people together better than a common enemy
343 / 60 brothers lost on that day.
Amachanic
Contributing NLG Member
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 308
Offline Offline

Gender: Male
Posts: 1392
« Reply #6 on: July 12, 2011, 11:20:25 PM »
I know one of the first things I do when I get an older machine in is to inspect the power cords. The way they are run in under the bottoms of these type of machines they get flattened and torn causing a direct short... I do agree with Neonkiss with the pulling the hopper and or reel assembly before you power it on the next time with a new fuse. If it still blows you know that they are not the problems, if it doesn't put one in at a time till you figure out where the problem is.. Look around inside once you have everything out, you could have a stray coin or two floating around in the machine causing your short.. Good luck and keep us posted..

Gary
Logged
If it's jammed, force it... If it breaks it needed to be replaced anyway...
Op-Bell
Contributing Gold NLG Member
Sr.NLG Member 501 to 1000 Post
*

Total Karma Storms: 326
Offline Offline

Gender: Male
Posts: 854
« Reply #7 on: July 30, 2011, 07:15:27 AM »
Ok, I'm back. I will have to pull out my 400 in the garage to see what that fuse is, but I will look and give you an opinion tomorrow.
Logged
Pages: [1] Go Up Print 
« previous next »
Jump to:  

SimplePortal Classic 2.0.5

If you find this site helpful, Please Consider Making a small donation to help defray the cost of hosting and bandwidth.



Newlifegames.com ™    Newlifegames.net ™    Newlifegames.org ™
   New Life Games ™    NewLifeGames ™  NLG ™ We Bring new Life to old Games ™    1-888-NLG-SLOTS ™
Are all Copyright and Trademarks of New Life Games LLC 1992 - 2021


FAIR USE NOTICE:

This site contains copyrighted material the use of which has not always been specifically authorized by the copyright owner.
We make such material available in an effort to advance awareness and understanding of the issues involved.
We believe this constitutes a fair use of any such copyrighted material as provided for in section 107 of the US Copyright Law.
In accordance with Title 17 U.S.C. Section 107, the material on this site is distributed without profit to those
who have expressed a prior interest in receiving the included information for research and educational purposes.

For more information please visit: http://www.law.cornell.edu/uscode/17/107.shtml.

If you wish to use copyrighted material from this site for purposes of your own that go beyond fair use,
you must obtain permission directly from the copyright owner.

NewLifeGames.net Web-Site is optimized for use with Fire-Fox and a minimum screen resolution of 1280x768 pixels.


Powered by SMF 1.1.20 | SMF © 2013, Simple Machines
Loon Designed by Mystica
Updated by Runic Warrior
Page created in 0.108 seconds with 19 queries.