Welcome, Guest. Please login or register.
October 05, 2024, 12:21:15 PM

Login with username, password and session length
* Home Help Arcade Login Register
.
+  Forum
|-+  Bill Validators and Currency acceptors
| |-+  JCM WBA 10, 11, 12, 13, 14, 20, 21, 22, and 23 Bill Validators
| | |-+  ID003 BASIC DRIVER SOFTWARE		 0 Members and 1 Guest are viewing this topic. « previous next »
Pages: [1] Go Down Print
Author Topic: ID003 BASIC DRIVER SOFTWARE  (Read 8169 times)
SLOTMAN
Contributing NLG Member
NLG Member 101 to 500 Post
*

Total Karma Storms: 34
Offline Offline

Gender: Male
Posts: 351
« on: September 18, 2011, 08:21:45 PM »
For the life of me I cant seem to get the ID003 basic driver software to work.  I keep getting "frame error" I am using a WBA13 of course with ID003.  This is a known good working unit as it works in the host and passes all the diagnostic tests.  I have tried the DP#8 on then off after power up and tried it without.  I am using a Unidesa harness which has a DB9 connector on the end (makes it convenient).  It seems like the pin #'s match.
With the attachments I have added you will see that I am using a RS232 to TTL adapter (im cheap and dont want to buy a JCM unit).  This TTL adapter uses pins 2,3,5.  As you can tell from the Unidesa harness the pins 2,3,5 coincide.

I am feeding the unit a direct 12V which I know is sufficent because it will allow me to go through all the self diagnostic tests and they pass.

If I put a jumper on the TTL pins 2,3 and use Hyper terminal I get a loopback or echo so I know that I am good up to that point. 

I am at wits end, anyone have any advice?
* xxx0200_23-002E_R1.pdf (46.7 KB - downloaded 863 times.)
* TTL-232-5P.pdf (126.82 KB - downloaded 827 times.)
Logged
Op-Bell
Contributing Gold NLG Member
Sr.NLG Member 501 to 1000 Post
*

Total Karma Storms: 326
Offline Offline

Gender: Male
Posts: 854
« Reply #1 on: September 19, 2011, 03:01:30 PM »
Parity. The WBA uses even parity. If the PC is set up for no parity, whenever the WBA sends a byte with a parity bit of zero the PC will see it as a framing error, because it expects a '1' stop bit in that position.
Logged
SLOTMAN
Contributing NLG Member
NLG Member 101 to 500 Post
*

Total Karma Storms: 34
Offline Offline

Gender: Male
Posts: 351
« Reply #2 on: September 19, 2011, 03:44:08 PM »
Op-Bell, something told me that you would have the answer.  I will try it later and report back.

Thank you
Logged
SLOTMAN
Contributing NLG Member
NLG Member 101 to 500 Post
*

Total Karma Storms: 34
Offline Offline

Gender: Male
Posts: 351
« Reply #3 on: September 19, 2011, 08:40:09 PM »
Using the following 9600,8,E,1,N I still get framing error with accload and waiting for communication with ID003 driver
Logged
Op-Bell
Contributing Gold NLG Member
Sr.NLG Member 501 to 1000 Post
*

Total Karma Storms: 326
Offline Offline

Gender: Male
Posts: 854
« Reply #4 on: September 19, 2011, 09:14:07 PM »
'Fraid I don't have the software so I can't check your setup, but the conventional way to write it would be "9600 E 8 1" - I don't think you can have an 'E' and an 'N' in the same setup.
Logged
SLOTMAN
Contributing NLG Member
NLG Member 101 to 500 Post
*

Total Karma Storms: 34
Offline Offline

Gender: Male
Posts: 351
« Reply #5 on: September 19, 2011, 09:30:52 PM »
Sorry, using the N for flow control N=Flow Control (NONE)
Logged
Op-Bell
Contributing Gold NLG Member
Sr.NLG Member 501 to 1000 Post
*

Total Karma Storms: 326
Offline Offline

Gender: Male
Posts: 854
« Reply #6 on: September 19, 2011, 09:41:05 PM »
AHA! What is this "ACCLOAD" of which you speak? You need the ID003 simulator to run the validator (free download from JCM). Accload is an accounting tool for reading out logged data, and needs some DIP switches set to work - also it's not supported in all of the WBA firmware..
Logged
SLOTMAN
Contributing NLG Member
NLG Member 101 to 500 Post
*

Total Karma Storms: 34
Offline Offline

Gender: Male
Posts: 351
« Reply #7 on: September 19, 2011, 10:02:03 PM »
I have mostly tried the basic driver and it hangs at waiting for comunication
Logged
Pages: [1] Go Up Print 
« previous next »
Jump to:  

SimplePortal Classic 2.0.5

If you find this site helpful, Please Consider Making a small donation to help defray the cost of hosting and bandwidth.



Newlifegames.com ™    Newlifegames.net ™    Newlifegames.org ™
   New Life Games ™    NewLifeGames ™  NLG ™ We Bring new Life to old Games ™    1-888-NLG-SLOTS ™
Are all Copyright and Trademarks of New Life Games LLC 1992 - 2021


FAIR USE NOTICE:

This site contains copyrighted material the use of which has not always been specifically authorized by the copyright owner.
We make such material available in an effort to advance awareness and understanding of the issues involved.
We believe this constitutes a fair use of any such copyrighted material as provided for in section 107 of the US Copyright Law.
In accordance with Title 17 U.S.C. Section 107, the material on this site is distributed without profit to those
who have expressed a prior interest in receiving the included information for research and educational purposes.

For more information please visit: http://www.law.cornell.edu/uscode/17/107.shtml.

If you wish to use copyrighted material from this site for purposes of your own that go beyond fair use,
you must obtain permission directly from the copyright owner.

NewLifeGames.net Web-Site is optimized for use with Fire-Fox and a minimum screen resolution of 1280x768 pixels.


Powered by SMF 1.1.20 | SMF © 2013, Simple Machines
Loon Designed by Mystica
Updated by Runic Warrior
Page created in 0.079 seconds with 19 queries.