Settiog % payout and credits per coin in

[David K]

I have an IGT S2000 multi denomination machine. It is a 3 coin 3 reel diamond 10 machine.
Here is what I would like to do.
1. Set the percent payout for each demonation to the highest possible.
2. Set the number of credits for each coin inserted ( 1 0.25 coin would equal 10 credits ), if I put in a quarter 10 credits would ring up on the machine.

I don't have a sheet showing all the options so any help would be greatly appreciated.

[Foster]

Do you have a Key Chip, usually a 17, 31, or 45?
A key chip is required to do the changes you want to do.
all the setting you want to change are in he key chip menu 7.1
Would help if you go into 7..1 and detail what your player denom, game denoms, and coin denom are currently (no key needed to look at them, only needed to change them)

Also go into 1 Accounting, Version Accounting and note what the Base, Game Chips, and Version Chip information
Base will be SB10xxxx, SB00xxxx
Game will be SG000xxx
Version will be VS0xxxxx

X is a number or letter.

Is the machine a multi-denom machine or only a single denom?
You can have the coin denom be any value you want, if not multi-denom and if you do not want to change from player denom of .25 you could change coin denom to $2.50 or even $25.00

if you need specifics let me know I will provide step by step instructions.

[David K]

PV1 Game  sg000362 5204
pv3 Base  sb100068 3bae
Version  vs011gx1 93b4

It is a mylti demonation quarter machine.

Step by step instructions would be very helpful as I do not have the menu structure.

[Foster]

Do you have a key chip?

IF you do you first have to enable the key chip menu.
No credits on the machine or the the following will fail!

Enable Key Chip Menu procedure:
1 open door
2 power off
3 remove mpu
4 locate the Base chip and remove it carefully.
5 install key chip make sure you align the notch on chip with socket properly
6 install mpu
7 power on, wait for 2 amber leds on the mpu
8 power off
9 remove key chip.
10 install base chip
11 install mpu
12 power on machine (DO NOT CLOSE THE DOOR)
13 Machine should come up with [7 Key Chip Menu]
14 Press Spin Reels

Max bet is the exit or go up a level, be careful when you press it while in the key menu (you press it one to many times) you have to enable the key chip menu again.


Spin Reels is go down or into that area, and will reset to the last previously stored value once in the option
Change, Cash out, bet one are your cursor and selection buttons
Note only the active buttons will be lit up for you.

Now you can not change your accounting denomination at all (if you also wanted change it, it requires a clear then a key chip)
Go into 7.1 denomination

first area you need to enter is 7.1.1.2 Coin Denomination
adjust with the change and cashout buttons until it is $2.50 (if your original denom was $0.25) if you are satisfied with it press max bet

do you want to change player denoms? then navigate to 7.1.1.3, I would leave as is unless you want to change it.
I am guesing your player denom is 0.25 as well or multi-denom.

Now we need to adjust your game percentages
Easy to do but the buttons only cycle one way in this area from highest percentage to lowest (about 5-7 preset values)
This is under 7.1.2 Game Selection
change button selects the player game, and cash out selects the paytable (percentage) highest is usually 97.9 to about 98.5 depending on what theme you have.

I am doing this with out enabling my menu

[David K]

Sorry, yes I have both the 97 clear and key 31 chips.
I have cleared the machine but I don't know how to set the percentages or the amount of credits per coin.

[coorslight115]

Sorry, yes I have both the 97 clear and key 31 chips.
I have cleared the machine but I don't know how to set the percentages or the amount of credits per coin.

read thru this attachment...it should help

[David K]

Thanks for the replies !!!!  The machine is now set up the way I want and I have enough information if I intend to change anything in the future.