Welcome, Guest. Please login or register.
November 25, 2024, 12:14:53 AM

Login with username, password and session length
* Home Help Arcade Login Register
.
+  Forum
|-+  General NLG Chat
| |-+  The Slot Shop **Tech Talk**
| | |-+  Can an opto isolator have degraded performance?		 0 Members and 2 Guests are viewing this topic. « previous next »
Pages: [1] Go Down Print
Author Topic: Can an opto isolator have degraded performance?  (Read 7662 times)
jbshocks
NLG Member 101 to 500 Post
***

Total Karma Storms: 21
Offline Offline

Gender: Male
Posts: 463
« on: September 27, 2011, 06:28:57 PM »
is an opto isolator simply good or bad or can they be intermittent or pass an inaccurate signal? 
Logged
ChizzleMonkey
New NLG Member 1 to 100 Post
**

Total Karma Storms: 4
Offline Offline

Gender: Male
Posts: 89
« Reply #1 on: September 28, 2011, 01:25:03 PM »
It depends on what testers and why you are testing it? Circuit boards have no end these days...
Logged
Keep it simple.
stayouttadabunker
Senior Full time Member.
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 1039
Offline Offline

Gender: Male
Posts: 13447
« Reply #2 on: September 28, 2011, 01:54:33 PM »
JB,
Where specifically is this optic isolator located and on what kind of machine?
Maybe we can help you more.

A general answer to your question would be "yes, they can go bad"...but
that would be my same reply to any other machine part too... rotflmao
Logged
cowboygames
Abbys Dad
Contributing Gold NLG Member
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 680
Offline Offline

Gender: Male
Posts: 3916


Happiness in life is a great dog
« Reply #3 on: September 28, 2011, 08:16:07 PM »
In all my years working on TVs I never came across anything but good or bad ones. Never saw one that was damaged but partially working. The ones I dealt with were in the power supply section. What are you dealing with and why do you suspect it's faulty?
Logged
jbshocks
NLG Member 101 to 500 Post
***

Total Karma Storms: 21
Offline Offline

Gender: Male
Posts: 463
« Reply #4 on: September 28, 2011, 08:44:26 PM »
this is on my cei slot.  The reel speed and position is detected by an optical sensor that feeds into an opt isolator.  The manual was  saying to replace the opto isolator but I did not believe it could be intermitent.   I have it working again and probably caused the issue myself.  Between adjusting the optical sensor air gap and forcing a reel calibration its back in action.
Logged
cowboygames
Abbys Dad
Contributing Gold NLG Member
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 680
Offline Offline

Gender: Male
Posts: 3916


Happiness in life is a great dog
« Reply #5 on: September 28, 2011, 08:46:46 PM »
Good job! Clap I figured you were working on a monitor
Logged
stayouttadabunker
Senior Full time Member.
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 1039
Offline Offline

Gender: Male
Posts: 13447
« Reply #6 on: September 28, 2011, 09:06:19 PM »
Quote from: jbshocks on September 28, 2011, 08:44:26 PM
this is on my cei slot.  The reel speed and position is detected by an optical sensor that feeds into an opt isolator.  The manual was  saying to replace the opto isolator but I did not believe it could be intermitent.   I have it working again and probably caused the issue myself.  Between adjusting the optical sensor air gap and forcing a reel calibration its back in action.
Quote from: cowboygames on September 28, 2011, 08:46:46 PM
Good job! Clap I figured you were working on a monitor

Sure sounds more like he's working with physical slot stepper reels?
I could be wrong...lol
It won't be the 1st time... rotflmao
Logged
jbshocks
NLG Member 101 to 500 Post
***

Total Karma Storms: 21
Offline Offline

Gender: Male
Posts: 463
« Reply #7 on: September 28, 2011, 10:28:53 PM »
What are physical slot steppers?  Hall affect switch with a slot in the reel?    These have a sensor with an led that shines against a series of wide and narrow reflective strips on the reel edge.  The reflection is picked up by an optical transistor that transmits back to the main board and the first step is an opto isolator.
Logged
stayouttadabunker
Senior Full time Member.
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 1039
Offline Offline

Gender: Male
Posts: 13447
« Reply #8 on: September 28, 2011, 10:34:44 PM »
Quote from: jbshocks on September 28, 2011, 10:28:53 PM
What are physical slot steppers?  

In the slot machine world...these are otherwise called...uh... "reels"...
Another term is>> "Stepper Reels"
They are controlled by the notches on an internal wheel passing through optics.
The wide/narrow reflective strips on yours is an upgrade (somewhat) to the older "notches"
for controlling the reels.
Logged
knagl
Global NLG Site Moderator
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 642
Offline Offline

Gender: Male
Posts: 5489


Kevin
« Reply #9 on: September 29, 2011, 08:46:31 PM »
His machine doesn't use stepper motors, I don't think.   no

Check out this post and the ones below it.  propeller
Logged
If you find this site helpful, please consider making a small donation to help defray the cost of hosting and bandwidth.

Please do not PM me for support or "how to" requests -- please post your request in the forum so that everyone may assist you and everyone can benefit from the answer to your question!  Thanks! Smiley
jbshocks
NLG Member 101 to 500 Post
***

Total Karma Storms: 21
Offline Offline

Gender: Male
Posts: 463
« Reply #10 on: September 29, 2011, 08:53:49 PM »
right no steppers.  tiny DC motors
Logged
stayouttadabunker
Senior Full time Member.
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 1039
Offline Offline

Gender: Male
Posts: 13447
« Reply #11 on: September 30, 2011, 01:49:05 AM »
Wow! That is one strange machine huh?
I've NEVER seen one before...!!!
Pretty cool link Knagl!  applause
I can honestly say that I know nothing about these CEI's...nothing! lol
I'd love to get my hands on one of those puppies just for the pure heck of it!
Logged
nightmaretony
In Remembrance of our lost NLG Members
New NLG Member 1 to 100 Post
*

Total Karma Storms: 100
Offline Offline

Posts: 54
« Reply #12 on: March 31, 2012, 02:10:13 PM »
Optos do indeed degrade. Had that issue with centipede and Tempest and back when we were designing Arkanoid all the time. they degrade, get less sensitive and need replaceent. Regapping doesnt help out., Maybe the emitting LED dims like LEDs do after time...
Logged
Pages: [1] Go Up Print 
« previous next »
Jump to:  

SimplePortal Classic 2.0.5

If you find this site helpful, Please Consider Making a small donation to help defray the cost of hosting and bandwidth.



Newlifegames.com ™    Newlifegames.net ™    Newlifegames.org ™
   New Life Games ™    NewLifeGames ™  NLG ™ We Bring new Life to old Games ™    1-888-NLG-SLOTS ™
Are all Copyright and Trademarks of New Life Games LLC 1992 - 2021


FAIR USE NOTICE:

This site contains copyrighted material the use of which has not always been specifically authorized by the copyright owner.
We make such material available in an effort to advance awareness and understanding of the issues involved.
We believe this constitutes a fair use of any such copyrighted material as provided for in section 107 of the US Copyright Law.
In accordance with Title 17 U.S.C. Section 107, the material on this site is distributed without profit to those
who have expressed a prior interest in receiving the included information for research and educational purposes.

For more information please visit: http://www.law.cornell.edu/uscode/17/107.shtml.

If you wish to use copyrighted material from this site for purposes of your own that go beyond fair use,
you must obtain permission directly from the copyright owner.

NewLifeGames.net Web-Site is optimized for use with Fire-Fox and a minimum screen resolution of 1280x768 pixels.


Powered by SMF 1.1.20 | SMF © 2013, Simple Machines
Loon Designed by Mystica
Updated by Runic Warrior
Page created in 0.103 seconds with 20 queries.